Printable View
Way to go! :up:Quote:
Originally Posted by billdavis
Did you take a screenshot of the 03 score?
You don't need to have a legit Futuremark link, it's only needed for Global Top 20.
36k in Vantage is the team's highest score, well done! :)
And pleeeeeeeeeeeeeeeeeeeeeeease run some AM3 this time....
will am3 run in win764?
Try to run it just after a regular install, if it doesn't work try this patch. Just overwrite the files.Quote:
Originally Posted by billdavis
345,154
Making fun of my pitiful C2D run... :shakes: :ROTF:Quote:
Originally Posted by Don_Dan
There was a lot more in that card, I barely OCed it. :(
The CPU also had much more in it, just didn't have enough time! It got shipped already....
On another note, my 5870 came in! I can use and be ready for the new single card ranking that the HWBot change will incur.... ;)
GO FOR IT CHEW*!!! :up:
Edit: Sounds like you have a killer setup running billdavis! :up:
I'm going to have to grab a core i7 system and two 5970s SOON.................... :rolleyes:
I'm not making fun... The only thing I'm making fun of is your RAM... :D
Did you read my comment, I think MCH ref voltage is to blame.
On a serious note, you got a decent score and you made it into top 20 of 03 globally, nothing to sneeze at. :yepp:
Oh you guys are having all the fun, I wish I had some time to OC again ( and some money to burn on a new VGA... :rolleyes: ).
To guys running crossfired 5870's - how do you get them to scale in Vantage? I always get the same score with single, two, three and four cards :( tried different drivers, no luck.
That must have something to do with how your installing the drivers...use 9.10 for nowQuote:
Originally Posted by xoqolatl
you have the lcd pluged in to your master card?
Yes, monitor to the first card, I'm installing the drivers on a freshly installed OS with one card plugged in, then reboot, plug other cards and CF bridges, enable Crossfire, reboot, vantage, fail. I'm gonna try again on a Classified (this was on P6T7 WS).
I did run the ram really loose...Quote:
Originally Posted by Don_Dan
I was letting it automatically control the timings just to check and see if the ram was messing up for some reason..
I was putting 2.2v into the ram.
I have this ram: http://www.newegg.com/Product/Produc...-256-_-Product
I haven't tested it past 1066mhz at 5-5-5-15 2T. I had the Dominator GT ram fans blowing on the modules by the way...
For some reason it just didn't want to run over 5.2ghz. It will boot and run good at 5.15 and run up to 5.2 sometimes but didn't go over that, even for a second with the Windows tuner.
Are you suggesting that the MCH core voltage at 1.8 might be tripping the motherboard?
I ran the same settings on another UD3P but I do understand that different mobos can need slightly different voltages to run the same clocks....
Thanks. :up:
I'm just teasing you with the RAM, memory is my addiction! ;)Quote:
Originally Posted by Linuxfan
No, I don't mean MCH voltage but MCH ref voltage, one step below MCH voltage in BIOS, it's usually set to 0.750 if I recall correctly. Try 0.770 and only change it in very small increments.
awesome run billdavis
what psu were you using?
Great score! What were your uncore and ram speeds?
Oh and I spy my AM3 tweak being used :lol: I always rename the shortcuts in case they make it to "official" screenshots :D
old pcp&c 1kw-srQuote:
Originally Posted by Hondacity
i really want to break 30k for cpu but something is holding me back and it aint voltage
wahhht??Quote:
Originally Posted by xoqolatl
where do i check what my uncore is
rams is 7-8-7-21 1t 9something
Under memory tab of CPU-Z?! You didn't know that?Quote:
Originally Posted by billdavis
So how high are you running your Uncore, maybe that's limiting you.
Please correct your AM3 screenshot, you need to have CPU-Z and GPU-Z in it and reload it to hwbot afterwards.
Mainly VTT.. on some chips Vdimm, and a little bit more Vcore can't hurt either ;)
Vtt if I recall correctly, that's the voltage that will not change in idle mode, correct? Then I'm right...
Yeah, right, VDIMM can help you to stabilize high uncore frequencies too.
Where did the question go? :D
http://i107.photobucket.com/albums/m...antagehigh.jpg
cool upped the vtt and got some 30kcpu action
Nice, but you can go higher I think. On SS right? Try for 4,6-4,8 uncore ;)
Great! :up:Quote:
Originally Posted by billdavis
Did you raise VDIMM too? Memory has a bit left I think.
seems to be my limit for vantage...i just need some help with the last 100 or so mhz's
i turnd it off so now i will submit all the scores
The CPU should be good for some serious clocks on DICE or LN2 if it keeps scaling like that, in case it doesn't have an early coldbug.
Please edit your AM3 screenshot, you need system info in it, in its current form it will get blocked sooner or later.
@bill
Great scores!!!:up:
I wanna see that system build...
i had better ones to submit...I have a problem getting a screen shot when in AM3's screen so i used the submit screen for all details and if somone crys then whateverQuote:
Originally Posted by Don_Dan
yeah i added some ram voltage but i added volts to everything!:up: