From DFI Street forums:Quote:
Originally Posted by _Eduard_
1. CABNE 05xx (excluding 0540) / CABYE 0540
2, CABNE 0540 / CABYE 05xx (excluding 0540)
3. CAB2E 05xx
4. CABGE 05xx
But then again its not certain...
Printable View
From DFI Street forums:Quote:
Originally Posted by _Eduard_
1. CABNE 05xx (excluding 0540) / CABYE 0540
2, CABNE 0540 / CABYE 05xx (excluding 0540)
3. CAB2E 05xx
4. CABGE 05xx
But then again its not certain...
Depends on how well you can OC and the individual chipQuote:
Originally Posted by _Eduard_
My CABGE was good for 2980MHz which was excellent but most ppl struggled for more than 2.8Gig with most CABGE steppings
Chipsetvoltage is maximum 1.8, LDT i havn´t touched, what can i set it on? Dividers is low so the ram is runnin in about 220 mhz can do 250
Anyone heard of a CABCE 0512? I may have a 150 with that stepping coming...
Whats the wattage of your chip in maxTcase?Quote:
Originally Posted by culex44
I got mine on 2.9ghz @ 1.5V(cpu-z) stable for now.Going to try loosen up the ramtimings.
What is your max async latency and read preamble
MaxTcase gives me 44.1 for the wattage.
My max async latency and read preamble are 8ns and 7ns respectively in my bios (1C3 TCCD modd by sideeffect)
Opteron 146 CABYE 0540 FPBW gives an high wattage !
http://img227.imageshack.us/img227/7...z14v9kq.th.png
Any feedback about CAB2E 0545 MPMW please-i might get one few days later?
So i got the same stepping as you and maxTcase so I should get the same results as you, but WC setup is borked atm. Need to fix or buy some new things.Quote:
Originally Posted by culex44
Did you write down the full cpu code down, if you do , plz post it.
@troman, check sig. Have it on 9 & 7 ns.
I don't remember the full cpu code but batch was 0338 I think. I'll post it when I'll get my DFI and so reinstall my cpu.
148 CABYE0543 FPMW
only been playing with it for a couple of days .....think i can push it further
i notice these opterons are very sensitive to mem timings especially RP,TREF & Drive strength taking me ahwile to get it nailed
http://img302.imageshack.us/img302/300/blah3ur.jpg
Just managed to join the infamous 3gz club on a crappy CAB2E. Week 40, 2005. here we go now:
do some beers too!
:toast:
:toast: :rotf:
http://www.xtremesystems.org/forums/...1&d=1133839221
http://www.xtremesystems.org/forums/...1&d=1133845067
http://www.xtremesystems.org/forums/...1&d=1133839221
http://www.xtremesystems.org/forums/...1&d=1133839221
Nice chip:toast:Quote:
Originally Posted by trans am
Can you pass 32Mb run on that vcore?
Any suggestions for those of us still in the trenches?? What do these opties seem to like for RP, TREF and Drive Strength??Quote:
Originally Posted by mouawad
:frag:
http://www.xtremesystems.org/forums/...1&d=1133843003Quote:
Originally Posted by [ r2 ]
awww wat. u can get it 3 on stock vcore?! lucky. mines can only get to 2.8 b4 i needa up it by .25. BAH!!!!
FWIW mine like tref of 3.9us 200 or 166 DS of 5/1 and preamble of 6/6.5Quote:
Originally Posted by dnottis
this is on some GSkill LE TCCD's 431
as soon as i throw my Ballistix back in it will be back to the drawing board :)
Nice trans am! :toast:
what cooling?
Im assuming using DFI board?
Looks like my sistem has a ram issue...cause I can pass Super_PI 32mb @ 210mhz and CPU 2950mhz...than changed to 250 2-2-2-5 v 3,2V and CPU @ 3ghz and can`t get more than 7 loops, S&M @90% CPU passed withouth any problems, but it gave me an error in ram test...so the CPU is stable but has some problems with rame divider or settings...cause OCCT fais within 3 minuets and prime in about 10 seconds at every VCORE and FSB I gave to the CPU (have tried only 280 and higher...)...
Regards,
Primoz
still playin with sweet spots. so far so good...Quote:
Originally Posted by [ r2 ]
this is air cooled using As5 and Hyper6 with 2 fans push and pull. temps load are around 36c
DFI bios 704-2BTA DFI ultra D nf4
saphire x1800xl cat. 5.11
ocz520w
mush reds
http://www.xtremesystems.org/forums/...1&d=1133850666
trans am - is that BH-5 your running with your opteron? UTT? BH-6.. its certainly not tccd @ 2-2-2 250mhz ;)
EvilCloudStrife,
Quote:
Originally Posted by trans am
Hows the 148 from ZZF doing?Quote:
Originally Posted by coop
Are there any CABNE 0544 EPMW results yet?
Haven't seen them..
67W :DQuote:
Originally Posted by Troman
Recieved mine today (opty 146), but got to work, maybe I instal it tonight.Quote:
Originally Posted by UTF Nightmare
so what is this maxTcase all about?
Nothing really, some lower maxTcase will go higher then an other do visa versa.Quote:
Originally Posted by wittekakker
Maybe look at the wattage instead because i see people getting higher clocks with higer wattage from maxTcase.
Yep I have the same issue, but for now i am at 2900mhz and ram synced with loosen up timings 3-4-3-7 prime stable.Quote:
Originally Posted by Primoz78
Quote:
Originally Posted by 187(V)URD@
...so you have the same issue with TCCD ram?...mhm...strange this...I was looking to sell my ram and go for TCCD but now...:confused:
Regards,
Primoz
Well i need to test more before i can confirm its my tccd but its more likely ram setting or memcontroller.Quote:
Originally Posted by Primoz78
I am still testing raw cpu speed and not so much ram/memcontroller.
Still my ramsticks are weird, I think one stick of ram doesn't like voltage above 2.6V and the other one needs more voltage to go higher. Still need to test them sepertly but from what i've seen in memtest i am quiet sure.
With my venice the maxed out at DDR620 3-4-3-7 @ 2.6V.
At the moment 2.9ghz stable at 1.525V real voltage.
http://img227.imageshack.us/img227/845/291472ur.jpg
http://img467.imageshack.us/img467/4...pugraph9ei.gif
http://img467.imageshack.us/img467/3...oltcore8uv.gif
well, tried my other 146 to see if my instability problems were caused by CPU, be that doesn't seem the case. It seems to have something to do with my m/b or memory. i still cannot run 270/280/290 x 10, but 300 x 7/8/9/10 is no problem! i wonder if you guys can still help me?
How good of an indicator is prime in real life usage as compared to say stability in spi32m and SnM? I have a proc that does ~2975 with 1.55v 32m stable, not sure about SnM. But it def does 2900 32m and SnM stable yet fails prime at 2900. To be fair though i think the prime issue may be related to memory/motherboard. Im using an epox 9nda3+ with gskill 2gb zx and i dont think the ram likes the motherboard. I really would like to know if anyone has played around with these processors on different mobos and seen large differences moving from one platform to another. At this point id like to say my mobo is the problem but i cant be sure.
Quote:
Originally Posted by 187(V)URD@
What are you using to read voltage and temps in occt? Does it read the DFI board automatically or do you need to configure it using something like speedfan? thanks.
I think he is using MBM...as I can see from the screenshot...
Regards,
Primoz
Quote:
Originally Posted by Primoz78
Duh. I feel like a dum dum. thanks man. :)
Well i am using speedfan for OCCT because OCCT takes my MBM dashboard away when mplented in OCCT:).
So i basicly use both.
Just wondering if 350x8 or 280x10 is better if the memory speed is the same for both.
@smartasian: performance should be the same.
htt link speeds may differ. try both and bench and compare results.Quote:
Originally Posted by smartasien
update: after tweaking ram settings with a64 tweaker it seems it has stabilized me at least somewhat, i'm now at 2950 with higher ram timings that, if i had tried booting at this speed with these settings without the a64tweaks it would have crashed immediately. So 2950 @ 1.55v seems at least somewhat stable, i really need to get this thing on a good oc'ing mobo with my new water cooling.
again my stepping is CAB2E 0545 CPBW
opteron 144 CABGE 0536 VPMW STOOkCOOLER
2844mhz@1.45v stable
http://img475.imageshack.us/img475/5...51455sy.th.jpg
the board its a asrock 939 dual stata2 but only can get 1,45vcore , when i make the VMODE i come back with more results. But for now i think 2844mz@1.45v stable its amasing :) .
:toast:
I'm keeping this one. 148 cabye 0543 fpmw. [IMG]http://img217.imageshack.us/img217/8...456v6gk.th.jpg[/IMG]
What settings exacty did you change to make the Opteron more stable?Quote:
Originally Posted by kemist
used gskill techs recommended settings for zx ram, some of which you cant edit in the 9nda3+ bios so a64 tweaker helped.
You would be correct about that. Please let us know the bios version you are running. I tried the 2nd beta bios at OCW and could get a little over 320HTT but had a cold boot issue wherein the HTT would not hold and kick back down on restart. Vcore had a nasty habit of resetting as well. Before I sold the Asrock I put the latest official bios on it and the HTT seemed to be capped at 272.Quote:
Originally Posted by mascaras
Thats a dirt cheap FX57 rig you have there :toast:Quote:
Originally Posted by mascaras
exactly like mine 146 CAB2E 0540FPMW 3ghz at 1.4v :)Quote:
Originally Posted by trans am
Tcase max 65c [IMG]http://img232.imageshack.us/img232/9...301456v6nx.jpg[/IMG] [IMG]http://img232.imageshack.us/img232/5...456v5yj.th.jpg[/IMG] 32m @3105 a couple post back.
coop: Nice clock and what cooling do you use?
Does my 144 0536 GPMW sucks? Can't get it prime stable over 2700 but it's 100 procent stable in games/windows and superpi @ 2843MHz. I guess my lack of cooling and contact between IHS and core may be a problem. Idle/Load temps are 36-38/55+ with a Thermaltake Venus 12. Have ordered a TT BT which should arrive til the weekend. My V-core is jumping from 1.55 to 1.62 all the time, not sure if my PSU give stable volts (Aspire 520W) Any suggestion how to get this a bit higher?
http://img224.imageshack.us/img224/9...ltat0vr.th.jpg
hi guys im stupid, my brother just bought a 144 CABGE 056 VPMW and a asorck939 dual sta2 and with stokcooler 2870MHZ@1.45v Pi8MB :slobber:
>>> http://img351.imageshack.us/img351/2...145v1ea.th.jpg
Yer saw it before, should be a law agin it :D :slobber:Quote:
Originally Posted by mascaras
Ok, nm about the stability from A64 tweaker, after looking into it more it seems it doesnt change my ram settings at all. The extra stability came from switching to 2T so i could get into windows properly. This is really annoying, i think this chip/ram have a lot more in them if i got them on a good system. I'll see eventually i guess.
Any Expert users with Opteron in here ? Want to know if there`s a better bios than defaultbios, e.g. 1117 or 1125. Anyone tried it and got better results ?
Got a 146 CACJE 0546 BPMW yesterday, not the best of clockers but a good enough replacement for my 2.7GHz Venice.
2850MHz @ 1.595v , won't do 3GHz but I have a 148 coming that hopefully will.
First time I saw a CACJE though.. anyone else?
szukalski,
Does your procs OPN end in DAA5BN... or perhaps DKA5CF?
hi guys , my brother already make the VMODE in asrock 939 dual sata2 and now he can get 1.55vcore , the 144 CABGE with the stokcooler and 1.55v can hit the 2950mhz STABLE and 3000Mhz for the pic , and note that the pics its with the OC from the bios its not a pic making OC in clokgen cause there isnt any program to OC in windows for this board .
Here the pics:
2950@1.55v STOOKCOOLER STABLE >> http://img365.imageshack.us/img365/181/21hk.th.jpg
3000MHz@1.55v STOOKCOOLER >>> http://img365.imageshack.us/img365/5489/30006if.th.jpg
:) :)
i think if the board have 1.6 vcore i can get 3ghz stable cause he can hit the 2950mhz stable with 1.55v
And also a litle thing its that the CPU dont have 24hours yet , with time maybe can go farther :) .
And for now its all , next step its past the CPU for the tower with WC and see if we can get a better board with more vcore.
BN.. What's the significance of that?Quote:
Originally Posted by largon
szukalski,
There's a new revision Opteron coming sometime soon. New DKA4CG "Venice" was spotted earlier and your strange 5-letter code made me suspicious.
Yes, I'm thankful for this cpu. Cooling, you've probably seen by now - in my sig I put a pic of it last night. Water with gallon milk jugs that are frozen. When the ice melts I can go get another one from the freezer. Return line runs into the top of the jug and it just flows into the cooler. Submerged pump. That is a 6002 clamped to my vid card. :eek:Quote:
Originally Posted by GUFY
largon, can you say any more about what you heard? Or link me to more info??? I've got this coming in the next several days:Quote:
Originally Posted by largon
http://img461.imageshack.us/img461/5007/150specs3hq.png
Very curious now. If this is Venice as in 512MB cache, there may be a return in my future...
Oh, got it from a reseller at ebay. Asked him where it came from he said:Quote:
couldn't really say. If you look at my "about me" page, it will
state that I'm generally clearing inventory for companies or
individuals who don't have resources to do so themselves. I've come
across some strange stuff: ancient Panasonic short wave radios not
sold in the open market since the 60's; large drives as big as a
phone with their own sound output controller; the original Intel 8086
"desktop" machines (I'd swear they were made out of recycled tank
parts) - even has a different Intel logo (slanted, Impact-type font,
no dropped "e"); etc.
Hey coop thats a nice ghetto rig you have there :clap: :D
Who needs FX-60?
Here is my Cabye 0540 on air:
Heres my week 43 CABYE :DQuote:
Originally Posted by joe2004
http://i16.photobucket.com/albums/b2...0ne/1M3133.jpg
Darn, this is the best I can do, still on air only:
Thanks, I thought someone would enjoy seeing it. :D Being able to keep fresh ice helps much.Quote:
Originally Posted by alpha0ne
anyone buy a 144 from monarch recently? (within the past 1-2 weeks, should of gotten it in the mail within the past couple days. there was a time it just got back in stock for $150then shot up to $200 where its at now) if so, what stepping/overclock are you getting
It looks like I didn't get it then, I got another Opteron, a 148, CABYE 0543 FPMW.Quote:
Originally Posted by largon
No results yet, cos I'm still looking at the box.
Interested to see the new ones though.
Your on a winner there, I wish I had/could have bought TEN of the same stepping :YIPPIE: :sonic:Quote:
Originally Posted by szukalski
I refered to the Venice just to point out that those new revision Venices are already out there. My point was that also the upcoming E6 Opterons will emerge soon(er or later). E6 Opteron will be an updated (into better or worse :confused: ) Venus core with 1MB L2 cache like E4 Venus. E6 San Diegos (closely related to E6 Venus) were already previewed on XS sometime ago.Quote:
Originally Posted by ixtapalapaquetl
But don't worry. Your Opteron is DAA5BN which means it's a current E4 Venus. :)
Edit: linky
Hello ... :)
Just put in a Opteron 146 -- Cab2e 0545 CPMW
running @ 2600 1.4V and stock (3000 venice cooler :eek: )
Have to go pick wife up i will have pics and hopefully the magical 3g later tonight :D :woot:
I think you'll max out at 2.8-2.9ghz. :stick:Quote:
Originally Posted by stestan
I just got a 148 CAB2E 0545 CPAW from ZZF for my brother-in-laws rig, gonna throw it in my Mach II and see how it does. I'll post back.
Mine is coming today!! I hope it does 5Ghz.
Just a little Super PI 1M @ 3088MHz with 1.70V :flame:
http://img415.imageshack.us/img415/7...30885zq.th.jpg
Here's that 148 CAB2E 0545 CPAW. Popped it into my old Neo2.
http://img265.imageshack.us/img265/5...cpaw0ox.th.jpg
How about 3.1 GHz on air, 32 MB SuperPi stable:
Here's my CABYE 0543 FPMW, SP2004 @ 3GHz @ 1.55v:
http://img474.imageshack.us/img474/9...t1pt55v2he.jpg
Pi1M @ 3.13GHz @ 1.65v:
http://img529.imageshack.us/img529/9...t1pt65v4se.jpg
seems like the newer week greater than 540 requires around 1.5v to 1.6v+ to hit 3ghz
This is driving me nuts. My CAB2E 0540 FPMW is rock solid 2.95 @ 1.45V.
http://img443.imageshack.us/img443/1...t2951455by.jpg
But nothing seems to be able to get it over the 3GHz mark. I've gone as high as 1.6v, removed the IHS, temps stay below 50C even at high volts -- nothing makes a damned difference. Never seen a MHz wall this sharp, or that kicked in at such a low voltage.
Give us a shot of a64 tweaker amp, maybe thats your problem.
LOL... 5ghz is really... ehrm well... optimistic, kind of :DQuote:
Originally Posted by yasoumalaka
Good luck with that cpu anyway, should do 3ghz :D
Opty 146 CABYE 0540 FPMW
2950 mhz @ 1,61 volts
I'm sure it can run at 2950 mhz with lower volts. It is currently running 2800 mhz @ 1,4 volts 24/7 with 100% load.
http://img390.imageshack.us/img390/963/29512905dy.jpg
Quote:
Originally Posted by FlyBoyGeo
i just got a 0545 CPAW as well from ZZF, glad to see it isnt a dog.
Ill test in my DFI expert perhaps.
Well I shot in the dark and got a CABYE from the egg, but like twenty pins were bent on it. They returned and another will be here tommorrow.
yeh you should run 2950mhz with 1.55vQuote:
Originally Posted by Orrefan
Yes! Some mem tweaks and I'm set at 3GHz even @ 1.55v.Quote:
Originally Posted by 187(V)URD@
http://img10.imageshack.us/img10/660...5vp23268fn.jpg
Just in case there are some more tweaks that might help:
http://img284.imageshack.us/img284/1...tweaker1qq.jpg
I'm running a piss-poor 2GB set, does 2-3-2-6 at 200, but tops out around 220 with 2.5-3-3-7. (My old 290MHz TCCD was nice for benching, but the real world started needing more address space.) Anything that might help with a 2GB setup?
So what did you change that got your clock from 2950 to 3000 MHz?Quote:
Originally Posted by aMp
We only have the "after" A64 shot.
what week has monarch been putting out for 148s?
With all the optys I have had nothing is a quicker stopper then memory settings. You need some different ram if you have to run those settings.Quote:
Originally Posted by aMp
Jus to let you all know I ordered from the egg and they sent me a CABYE WEEK 43
week 43 is a decent one
i haven't seen to many poor clockers in this group ....mine included - you're looking 2.85ghz+ prime stable stock volts
good luck
New Egg sent me a 144 CABNE 0544, the rest of my stuff will be ordered this weekend, so hopefully by next weekend I will be set up and ready to rock.
For those interested (looking for a specific stepping) I received a 148 CABYE 0543 FPMW from Newegg today.....I ordered the "retail" (boxed) version last Saturday. Hope it works as well as some of the posts are indicating.
:eleph: :cheer: :party: :YIPPIE:
The most replied to thread was the neo2 939. In 1 year, 2 months and
6 days it has had 3740 replies.
This thread in 74 days has had 3740 replies. It just goes to show that if you build a great oc'ing cpu for a good price, they will sell like hot cakes. The opty is a great shot in the arm for single core oc'ing.
I can answer that tomorrow...:toast:Quote:
Originally Posted by ZX7891
Quote:
Originally Posted by FlyBoyGeo
This is what I got today.
Generally, how good is week Cabye 0540 FPMW?
Week 40s are good. You should have a good cpu there.Quote:
Originally Posted by EboNova
I'm about to buy a new one, my old one were a 0536GPMW that wouldn't go over 2750 so I hope this one get's me over 3.0
Check out my results with that stepping in my log.Quote:
Originally Posted by EboNova
They're pretty sweet :)