DFI 965-S is here! For sale @ ewiz

Printable View

Show 100 post(s) from this thread on one page

05-21-2007, 08:11 PM
Bail_w

Quote:

Originally Posted by nealh

3420 8x380..stock + 175mv L47G431..not a great chip.. bios reads 1.5v...DMM idle is 1.5v, load is 1.48v
NB,SB,Vtt default...initially ran all defaults on ram..only change was cpu vcore and fsb(last night it ram P95 for about hr..this am..it would have an immed reboot....

so....

well I have issues with my ram

Ram vdd..default is 1.9v..DMM reads 1.83v
set 2.0 v and DMM reads 1.9v
set 2.1v and DMM reads 2.08/2.09 idle..load is 2.04/2.05

I am using Crucial Ballistix DDR1000..when running at 2.0v(dmm reads 1.9v) at 3400..380x8...4-4-4 I get immed reboot in P95.....set to 2.1v, still 380 1:1 4-4-4 reboots after a few min

380x8 1:1..5-5-5-15 @2.1v....P95 is running 45min

I am surprised this ram is not able to do DDR760 at 4-4-4 at 2.1v

you should read the previous pages regarding about the DDR configuration settings.
05-21-2007, 10:58 PM
awhir

ok guys thanks the ram now passed 475:D

1 more thing core temp does not work with my pc .when i load it it up it just stays at 18C and doesnt more.

anyone know anything about this.
05-21-2007, 11:58 PM
Bail_w

Quote:

Originally Posted by awhir

ok guys thanks the ram now passed 475:D

1 more thing core temp does not work with my pc .when i load it it up it just stays at 18C and doesnt more.

anyone know anything about this.

you should download the latest version of speedfan, it is the same reading as core temp.
05-22-2007, 04:19 AM
nealh

Quote:

Originally Posted by Bail_w

you should read the previous pages regarding about the DDR configuration settings.

I have looked at numerous pages but the settings are all over the place..also I have not seen any crucial ballistix ddr1000 in the thread
05-22-2007, 10:27 AM
Bail_w

Quote:

Originally Posted by nealh

I have looked at numerous pages but the settings are all over the place..also I have not seen any crucial ballistix ddr1000 in the thread

ya but if you read the previous couple pages, many people having success if you put your settings like this:

DDR Configuration = Mode 3
GTL+ Driving Strength = Mode 2
Enhanced Data Transmitting = auto
Enhanced Addressing = auto
DQ Calibration: Auto
Channel 1/2 CLK Fine Delay = Auto/Auto

and increase VTT to 1.36v
05-22-2007, 10:41 AM
hausner

hi!

Someone can post here his PC2-6400 FirestixFSX800D2C-K2G settings ?
05-22-2007, 10:46 AM
Bail_w

Quote:

Originally Posted by hausner

hi!

Someone can post here his PC2-6400 FirestixFSX800D2C-K2G settings ?

Try the settings above your post.
05-22-2007, 10:55 AM
The Nemesis

Quote:

Originally Posted by nealh

3420 8x380..stock + 175mv L47G431..not a great chip.. bios reads 1.5v...DMM idle is 1.5v, load is 1.48v
NB,SB,Vtt default...initially ran all defaults on ram..only change was cpu vcore and fsb(last night it ram P95 for about hr..this am..it would have an immed reboot....

so....

well I have issues with my ram

Ram vdd..default is 1.9v..DMM reads 1.83v
set 2.0 v and DMM reads 1.9v
set 2.1v and DMM reads 2.08/2.09 idle..load is 2.04/2.05

I am using Crucial Ballistix DDR1000..when running at 2.0v(dmm reads 1.9v) at 3400..380x8...4-4-4 I get immed reboot in P95.....set to 2.1v, still 380 1:1 4-4-4 reboots after a few min

380x8 1:1..5-5-5-15 @2.1v....P95 is running 45min

I am surprised this ram is not able to do DDR760 at 4-4-4 at 2.1v

My cpu did 3.820 on RD600(winter assisted) 3720 on evga, BFG, & 3631 on p5B Deluxe. So far I've only gotten 3730 to pass 12 hours orthos on this board. To eliminate my memory as the reason prime fails in 2 -3 hours, I ran memtest for a few hours. After an 8 hour pass @ the same settings that failed prime, I've decided either the board needs more tweaking or the cpu too hot. I'm thinking its the cpu heat. Anyway, have you tested your memory with memtest to see if you get errors? If it doesn't chances are u either need to tweak the board some more or you've reached the limit of your cpu.
05-22-2007, 12:21 PM
yenclas

Quote:

Originally Posted by The Nemesis

My cpu did 3.820 on RD600(winter assisted) 3720 on evga, BFG, & 3631 on p5B Deluxe. So far I've only gotten 3730 to pass 12 hours orthos on this board. To eliminate my memory as the reason prime fails in 2 -3 hours, I ran memtest for a few hours. After an 8 hour pass @ the same settings that failed prime, I've decided either the board needs more tweaking or the cpu too hot. I'm thinking its the cpu heat. Anyway, have you tested your memory with memtest to see if you get errors? If it doesn't chances are u either need to tweak the board some more or you've reached the limit of your cpu.

I have the same problem and I RMA the board because, with default settings in bios but with 2,0 or 2,1 vdimm in my GSKILL DDR800 HZ my systems reboot in Orthos at one or two minutes.

The technician is testing my system and he told me that he test the system with other memory (TeamXtreem) and the system runs fine. I don't think that the problem is RAM because I'm sure that it runs in other motheboard very well ( ASUS P5W DH Deluxe ). I think the probelm is that motheboard.

I'm thinking seriously to buy a Gigabyte P35 DS4.

sorry by my bad English.
05-22-2007, 12:30 PM
doom_st

it's not the board...
i am finally stable @ 525x8
1.48vcore
2.22vdimm 4 4 4 9 4 30 2 10 10 2 8 6 5 5 4 4
1.5vtt
without reboots.
05-22-2007, 01:00 PM
The Nemesis

Quote:

Originally Posted by doom_st

it's not the board...
i am finally stable @ 525x8
1.48vcore
2.22vdimm 4 4 4 9 4 30 2 10 10 2 8 6 5 5 4 4
1.5vtt
without reboots.

I don't think its the board either. I think its just picky with certain micron d9's trying to determine which now. Micron D9GKX (B6-25E) seem to be most successful, followed by Micron D9GMH (B6-3). I'm wondering if its the PCB used. Doom what were the rest of the memory settings? auto auto Fast Fast auto auto?
05-22-2007, 01:48 PM
yenclas

Quote:

Originally Posted by The Nemesis

I don't think its the board either. I think its just picky with certain micron d9's trying to determine which now. Micron D9GKX (B6-25E) seem to be most successful, followed by Micron D9GMH (B6-3). I'm wondering if its the PCB used. Doom what were the rest of the memory settings? auto auto Fast Fast auto auto?

Thanks,

but I tested the system with other memory and fail too. Do you think that I cannot do anything to stabilize my system with my configuration ?

Have I to sell my memory or my board if technician return to me ?
05-22-2007, 01:56 PM
Bail_w

Quote:

Originally Posted by yenclas

Thanks,

but I tested the system with other memory and fail too. Do you think that I cannot do anything to stabilize my system with my configuration ?

Have I to sell my memory or my board if technician return to me ?

what are your settings man, because i have GSkill HZ and my system are 100% stable.
05-22-2007, 02:02 PM
yenclas

Quote:

Originally Posted by Bail_w

what are your settings man, because i have GSkill HZ and my system are 100% stable.

I tested with very changes in the bios that I saw in this post.

What is your settings ?
05-22-2007, 02:06 PM
Bail_w

Quote:

Originally Posted by yenclas

I tested with very changes in the bios that I saw in this post.

What is your settings ?

my settings were posted in the previous page.
05-22-2007, 02:17 PM
yenclas

Quote:

Originally Posted by Bail_w

my settings were posted in the previous page.

Thanks, but with your settings my system hangs too.
05-22-2007, 02:23 PM
The Nemesis

Quote:

Originally Posted by yenclas

Thanks,

but I tested the system with other memory and fail too. Do you think that I cannot do anything to stabilize my system with my configuration ?

Have I to sell my memory or my board if technician return to me ?

Okay but did you test with memtest or run prime again? A failed prime blend can be a problem with memory settings, voltage, or cpu. I always run memtest to rule out memory issues or run FTT's instead of blend. If your system will loop memtest #5 for 8 hours or so, then chances are your cpu need more volts or has reached its ceiling. Secondly you could simply need additional voltage in other areas such as cpu-vtt or nb core.
05-22-2007, 02:32 PM
burningrave101

Well my DFI P965-S Dark is uninstalled and my new Asus P5k Deluxe is up and installing XP64. If anyone wants a DFI P965 let me know cause it's hitting eBay soon.
05-22-2007, 02:40 PM
The Nemesis

burningrave101 what ram did u try with your board?
05-22-2007, 03:38 PM
Bail_w

Quote:

Originally Posted by yenclas

Thanks, but with your settings my system hangs too.

Why dont you just post your settings and i will take a look at it.
05-22-2007, 04:13 PM
nealh

Quote:

Originally Posted by The Nemesis

I don't think its the board either. I think its just picky with certain micron d9's trying to determine which now. Micron D9GKX (B6-25E) seem to be most successful, followed by Micron D9GMH (B6-3). I'm wondering if its the PCB used. Doom what were the rest of the memory settings? auto auto Fast Fast auto auto?

I am sorry..I was not real concerned on the cpu overclock..the chips is not great..best maybe 3500..

I was just perplexed at ram (Crucial Ballistix DDR1000).....I expected at 380 fsb it would easily be stable at 2.0v....but with auto settings it sets to 4-4-4 at 2.0v this is a no go...

in fact I am still testing but 380 1:1 5-5-5 looks to need 2.05-2.1 v

Now I have not tweaked the settings...but I did not think 380 fsb at 1:1 would be a tight enough latency to cause issues

I am not blaming the mobo or my cpu...just really surprised..I guess I expected too much based on my ignorance
05-22-2007, 04:25 PM
The Nemesis

What I remember of my crucials compared to my g. Skills was their default voltage is 2.2 for their entire Ballistix line. I would not think that under 2.1 would be possibe @ any frequency above PC2-5300. You are simply undervolting your ram, thus it's failing.
05-22-2007, 04:53 PM
nealh

Quote:

Originally Posted by The Nemesis

What I remember of my crucials compared to my g. Skills was their default voltage is 2.2 for their entire Ballistix line. I would not think that under 2.1 would be possibe @ any frequency above PC2-5300. You are simply undervolting your ram, thus it's failing.

I am comming to that conclusion

My 10th anniv runs DDR780 4-4-4-12 at 2.0v..so I had hoped the Ballistix would undervolt at DDR760....but it appears I am asking too much of the ram

I just tried DDR 952 5-5-5-15-30 at 2.2v(mobo delivers only 2.2v by DMM)
..man these stick get real hot at 2.2v...with Prime running
05-22-2007, 05:19 PM
doom_st

Quote:

Originally Posted by The Nemesis

I don't think its the board either. I think its just picky with certain micron d9's trying to determine which now. Micron D9GKX (B6-25E) seem to be most successful, followed by Micron D9GMH (B6-3). I'm wondering if its the PCB used. Doom what were the rest of the memory settings? auto auto Fast Fast auto auto?

ddr mode3
gtl mode2
fast
fast
dq 5
auto
auto
05-22-2007, 05:38 PM
The Nemesis

Quote:

Originally Posted by doom_st

ddr mode3
gtl mode2
fast
fast
dq 5
auto
auto

Your chips must be based on Micron D9GKX (B6-25E)

Show 100 post(s) from this thread on one page