Printable View
I've had no issues with this chip and board combo. One of the first things I did was change the multi from 11 to 12 for a 3.2 over clock. I've taken it as high as 13 and as low as 9 to play around with different settings. Using the 1305 Bios too.Quote:
Originally Posted by goreblast
That's precisely what I'm using. The file I have on disk is 1103KB.Quote:
Originally Posted by revenant
-phil
I was being very stupid - all I needed to do was hit the delete key and type the new multiplier in! I was trying enter and the arrow keys.
Hi,
I need your help.
My computer is
Conroe 6700
ASIS P5W DH DELUXE
Seagate 250 GB (SATA connected on SATA1 with the red cable)
DVD-RW (as Master on the PRI_IDE - the blue port)
CD-ROM (as Slave on PRI_IDE - the blue port)
All is working fine till today.
Today I connected an IDE HD on JMicron IDE (PRE_EIDE - the black port) and now, after POST and the first Windows screen (this one with the logo) the computer hangs up.
The HD is set up as Master and is correct recognized by the BIOS.
After the POST, the Windows starts but after the LOGO-Screen it hangs up.
Any ideas?
Thanks in advance
Check in the BIOS to make sure that this drive is not at the top of the boot order. Perhaps, your machine is trying to boot from this drive.Quote:
Originally Posted by mortanon
-phil
I'm priming 390x9 and it runs around 40~43
then all the sudden, PC probe2 CPU sounds alarm and temp jumps to 256c ???
goes back down to normal when I turn it off...
i'm guessing there is something wrong with the probe
is there latest version I can download?
Quote:
Originally Posted by importpsycho
mine does the same thing.. not sure why.. must be a bug!
Yeah, this is stated on the first page of this thread :). Try using a different program.Quote:
Originally Posted by revenant
Mortanon,
I take it that ya DO have the Jmicron IDE enabled? and that if you want to boot off of this HD, you do have Jmicron boot enabled?
If above are true, and this is the only device ya have on that ribbon, try to pull the jumper (master set on the drive) all together. That's what worked for me on my WD drive..
Rick
How can i flash my BIOS on P5W DH Deluxe without Floppy Drive (in windows) because i don't have one???
From MB driver CD install AsusUpdate, that will let u flash bios in windows.
FDD are cheap i got 5x FDD for US$17 2nd hand hehe
flashing in dos much safe than windows
your choice grab a FDD for a few bucks or screw up a motherboard :D
FDD may be cheap but imo the disks are slow, fragile and unreliable, I use a thumbdrive instead.
I got a USB floppy so I can use it when I need to.. works great for the occational bios flash . . . for any of my machines. :)
So, question for you all: when you started with OCing, did you set your FSB termination and MCH Chipset voltage to 1.50 (the highest available value) ??
No mate i got my MCH runinng on Auto and doing FSB400 now stable ;) I guess it depends on the mobo.. but till about 360FSB all auto should be just fine.Quote:
Originally Posted by revenant
ok - thx for the info. Slowly getting used to this bios.. it's quite a change from the DFI bioses I am used to.
5 conroe boards from Asus - A Top To Bottom Comparison : http://www.gamepc.com/labs/view_cont...ookie%5Ftest=1
:)
Was running my new P5W (first two died, 2nd one mysteriously), testing my various memory to see if it performs better on this board (all but one stick did--my old board was crap with memory clocking).
So I go to push that one lame-duck stick (worst clocking of the 5 sticks I have too....), 470 4-4-4-8 is its usual 1M max, which it does fine. I push to 471 and run again....~6th instance it freezes (notice the freeze, not the typical error--and it didn't hard-off after a few seconds like a CPU error usually does), and this was ~450MHz short of my CPU's max 1M speed....system never comes back up, giving memory error post code (1 long, 3 short) with any of my 5 sticks of memory, in any of the slots. Tried a battery pull, still didn't come up after with the same testing techniques....:(
Anybody got a fix for a fubard board? :rolleyes:
Hi guys/gals...
Could some kind soul host the 1401 bios for XS??
I am having issues trying to download it from one of the links provided here...
Just wondering, is there an issue with that bios & Asus have banned it??
Every time I try to open that page for bos d/load, I just get an error..
Any help appreciated...
P5W BIOS 1401
this is being hosted on my free angelfire account lol
have fun
Hiyas...
Ummm.. when I click on that link, it gives me a "do not direct link" response??
nvm... copy/paste trick works with it at least... Unlike the other one that was posted around the web...
Thanks again everyone for the quick responses!!
Well my P5W DH mysteriously desided to die/not work anymore today whilst running @ default everything after doing a reinstall of XP Pro
I am tossing up whether to try out the P5B Dlx ???
Look here. <lots of BIOS'sQuote:
Originally Posted by m0da
It's german, but you can work it out :)
so what's the general concensus on 'performance mode' being on turbo? safe to do?
split - it's hard to type with your avatar bouncing around. lol.
I use turbo always..