Hmmmm :( I have a 3200 0520 BPMW that so far have only been able to get 2400 default Vcore (1.344 in CPU-Z) :mad: , still early days thoughQuote:
Originally Posted by Leverpospade
Printable View
Hmmmm :( I have a 3200 0520 BPMW that so far have only been able to get 2400 default Vcore (1.344 in CPU-Z) :mad: , still early days thoughQuote:
Originally Posted by Leverpospade
Quote:
Originally Posted by burningrave101
Yes, week 15 seem to have a very weak mem controller. Didn't allow my BH-5 run with 2T timing @ over 245 2-2-2-5. Is there any BIOS can fix this problem ? ?
There are two things that can help you to solve this problem:
- Disable Bank Interleave
- Sell the processor :stick:
Good luck
My venice week 15 can run my Tccd at 290 and my single stick ch-5 at 260 1.5-2-2-5 with 3.4vQuote:
Originally Posted by vozbidder
My tccd at a claw hammer cpu was able to run at 315 at 2.8 volt....but now with this venice i was able for 290 at 3.1 v and 2.5-3-3-5 (always memtest stable)
Here with my week 15 I can run 300 FSB 1:1.
E aeeeee Higher!!! :)
Hi guys,
I was wondering how much voltage is safe to run 24/7 on a Venice 3200? 1.6v? 1.7v?
Thanks!!
AleX
E ae Alex.. hehe.. blz? :) :***
I think 1.65v would be a safe bet! In the air I wouldn't go for more.
Good luck!
I would stick to no more than 1.6V for every day usage.
Depending on coolingQuote:
Originally Posted by higherøx
If you have air cooling i think that 1.55 its ok
For water 1.65
And on dd 1.75
Quote:
Originally Posted by OverClocker_gr
Have you tried to run tight timing @ 250 2-2-2-5 ? Really disappointed about my 3200 week 15, althought it has impressive OC result :(
Do you guy have any BIOS to fix the mem controller problem ? PLzz show me 1 :toast:
Quote:
Originally Posted by vozbidder
So.. yes i tried 260 at 1/1 at 1.5-2-2-5Quote:
Originally Posted by OverClocker_gr
sry bro , i wanted to know about dual , not single stick :D
I think that there will be no difference if the controler cant handle it...
btw with my tccd at 2-3-3-5 i am able to run at 255
I had my vapo SE installede last nigth, but I had a lot of problems getting the 939-kit to fit. After 2 hours I managed to get it to fit, so it could keep an okay temp.
Right now I'm running around 5-10 C idle, but in load it sometimes jumpes up to around 35 C :confused:
But here is what I have been able to do so far:
http://photobucket.com/albums/a120/L...zsuperPI1m.jpg
Anyone know how to bring down the PWMIC temp, cause it's seams quite high..
My mobo won't clock over 350 FSB, so have anyone got suggestion to how i can get higher??
Hope you understand my bad english
ok here what i have done ... i changed my 3500+ (CH) to 3500+ ( Venice )
and iam very happy with until i reached with it to 2.65Ghz @1.43V.
the problem is .. During Prime95 CPU Torture TEST to see the Stability .everything seems OK. ( no Errors for over 2 hours)..but when i reach 2.7Ghz Prime95 does not give me any errors..no.. instead the comp hangs without any warnings..
so i think my PSU is the Problem ..right? i have 18A in 12+ Rail.
help plz
It could be, 18A on the +12V rail is kind of low, as i've said before, it's recommended to have 26 or more amps on the +12V rail for AMD64 Xtreme OCing. I have dual 18A rails and they kind of suck, instead of prime95 erroring i get voltage droops under load and reboots. A more powerful PSU would be a good idea.
Reboots or prime95 hanging is caused by low voltage, give it more and it should be fine... but again, i think the low voltage is associated with teh voltage drop under load, my voltage goes down by ~.016 under load, which doesn't sound like much but *perhaps* that's the difference between fully stable and not fully stable.
so what Psu do you recommand me to buy??Quote:
Originally Posted by Absolute_0
i need the Psu to be fully stabilty at very high overclocking.
thank you
I'm not sure, antec550 and powerstream 520 are pretty popular. Can't go wrong with PC Power and Cooling or a high end Zippy though ;)
will antec550 do the job perfectly??
Look my 3200 has a new friend :banana: I got it earlier today but about 15 mins in I had to step out. Should have some results later tonight! :toast:
http://img214.imageshack.us/img214/4...wfriend8xl.jpg
What PSU you use to get that high of Oc'ing??
Your +12v rail must have more than 25amps for stable o/c
can you guys tell me which is the Best PSU for high overclocking for around 170$ ??
and Btw iam running Q&C = Default, the 12+=11.84v and @ 2.65Ghz ,12+ = 11.56v Idle and 11.36v @ load then boom restart :mad:
I picked up the Ocz modstream 520watt yesterday it has 28amps on the 12volt and a 12volt peak of 40amps, so far so good, I haven't had chance to test it fully yet but yesterday I tried 1.75vcore in corecenter and it didn't shutdown. So mayne soon When the a/c is on max I'll try some higher vcore, does this board undervolt or what? If i set 1.60 in corecenter i get 1.52 in cpu-z whos right and where can i test with Multimeter?
I just noticed that Now with 1.6 in corecenter I get hihger vcores :D 1.55 now lol sweet so I can probably low it abit and still be stable, I had 18amps on my old psu looks like it really was a problem.
i found Vantec VAN-520A.. it got 28A on 12+ rail , 52A on +5 Rail and 26A on 3.3V ,,,what do you think?
other than that they got Enermax 600 and 550 watts PSU's and thos is really bad on 12+ rail ,, i know that they got 2x12+ but i dont need it cause they carry out 18A on both of them.