Printable View
Quote:
Originally Posted by Spinal
What is your voltage you set in BIOS? CPU-z is very off. I get 1.36 in software when I'm really at 1.41 or something... yea... Does your Sandy prefer 11x or 10x multipliers? Just wondering cuz I got an 0522 like you too
I have the same stepping but I haven't had time to test it yet. Let me know your results when u get them :)Quote:
Originally Posted by afireinside
2.75 3d stable "ghettotek watercooled" ;) Water is probably around 35C since 30C ambiant and its after my x800 in loop.
just picked one of these up to tide me over. the stepping is 0518WPAW CABHE just got it in my phase and started messing with it. not sure if its going to be a good one or not? seems that the chip doesnt like the 11x multi over 230 1:1 wich seems odd cause 10x i can get 280 and hope to get atleast 300x10 before its starts taping out on me.... looking at the oc section these 3700's are getting some sick oc's! i was praying i got one like those guys have but i may have gotten a lemon? too early to say ill i gues seeings how ive only had it going 20 mins tops!
peace perc,
is there only one fx57 (939) the san diego to buy?
Just got my 3700+ SD...anybody knows if this is a good stepping...CABHE 0525UPMW?...I`m not home at the moment and I can`t wait...;
Regards,
Primoz
I saw today an FX57 0520MPMW 0021 but it cost +1.1k€ so that's it :cord:
How about these 4000+ SD, any good with new steping?
What's the newest stepping on 4000+ SD 05**?
Is it worth to try :D
...the SD 3700+ metnioned above is not so good...i can hit 2,75ghz but with 1,6V :slapass: not much faster than my Venice at 300*9...I`m thinking of returning it and go for an X2 3800+ :rolleyes:
Regards,
Primoz
This is my FX57 on air just surf stable but anyway on air bech stable at 3189mhz on air
http://valid.x86-secret.com/show_oc.php?id=32645
http://upl.silentwhisper.net/uplfold...4/PICT1119.jpg
have this monster cooler with a tornado 80mm on , seems to look good for OC with DI on next friday:)
sorry forgott the stepping on it CABCE 0516WPMW
Quote:
Originally Posted by chefnr1
nice and i like that setup in your rig. this cpu will fly when you freeze its ass off. yikes the noise of an 80mm screamer! :D
HAHA yes that tornado on att over 6000rpm you need earplugs the noise from it goes through walls :)
the temps on it in idle is 34-35c and on full load load cpu stresstest 42-43c at vcore 1,52v
My 0524XPMW is very bad. 2250Mhz with 1.4v is the highest stable setting :( Is the UPAW or UPMW 0525 better?
I have left it burning over the night and now started Prime...will see if it is stable when come home from work...hope it is :rolleyes: For now I can get 250*11 at 1.6V...Water cooling is under construction and when it will be done I will rise the voltage to 1.7V and hope I can get further.... :rolleyes:Quote:
Originally Posted by Riverna
Regards,
Primoz
It looks like you might be able to mount 2 - 25mm x 80mm fans front and back. It should be quieter. I'm curious how it would compare moving air over the radiator fins.
I have a SD 3700+ and it is not a good OC-er...I can get to 250*11 but stable with 1,64V...after burn in (and it get to about 62°C in full load at 1,64V)...so I`m indecided to take it or just buy it (I have a buyer) and go for an X2 3800+ E6...any suggestions?
Regards,
Primoz
My new 4000+ SD 0524XPBW 2603MHz @ 1.39Vcore AIR Prime95 Large now for 21h30min
Will try 2650MHz @ 1.39V ;)
Just keep burning it in. I am sure it will oc more in time.Quote:
Originally Posted by Primoz78
Quote:
Originally Posted by Crazykooter
Ok mate...I`ll try to burn-in for another 10 days...and wait for better results :rolleyes: But if I try to get 255*11 at any voltage CPU burn-in run just for a few minutes than reset the comp... :confused:
Regards,
Primoz
2702MHz @ 1.39V Prime95 LARGE for +15h with ZM7700CU ;)Quote:
Originally Posted by Dani
Gonna try if 2.8GHz will Prime @ 1.39V :eek:
I put my IHS back onto my 3700 SD and gained back my oc. I was stuck at 2800 mhz max with it naked and now with it back on I can do 2904 mhz again. Go figure. Some get lucky without IHS and some like me dont. The reason I put it back on tho was due to the resistors on the cpu were touching the water block which wasnt good at all imo. I will post some screen shots once I get it tested out more. I play BF2 for 2 hrs and if it doesnt crash then its stable as a rock. Prime95 is a joke Imo. Fails when it shouldnt.
Run OCCT then for 30min. ;)Quote:
Originally Posted by Crazykooter
OCCT
Goddness I've had the worst time with my computer the past few days. OCZ wound up replacing my ram (terrible RMA experience). Got replaced with some of the new TCC5 (i assume it is, since it says v1.1 on the sticker). My memory overclock still pretty much sucks. Can't go over 240 or so. But on to what this thread is all about. I've got a 3700+ CABGE 0522XPMW stable at 270x10 1.55v. I think it will still be stable at lower volts, too (or higher clock for that matter). Running a 166 mem divider so memory is only at 225. 20 hour prime stable. Haven't done too much tinkering cause I just got the system back up yesterday and managed to kill the bios today (that was fun to fix). I'm sure I'll get more into it this weekend. Oh, it's with an XP90 and panaflo fan.
yup
charlie
I have 3700+ SD like Primoz78 and this stepping sucks! (CABHE 0525UPMW) I can hit only 2750MHZ on 1.58V... :(
Well im waiting on an RMA for my GPU...
before i can set up my new rig... :(
Here is the stepping CABGE 0524XPAW
Anyone running this stepping...?
It passes occt every time but fails prime. Never had much luck with prime. I think its way to sensitive for my liking.Quote:
Originally Posted by Dani