guys, please keep silent.
Here (US) still under NDA :toast:
1.488v 3196mhz with Chilly 1 mod Mach II
1gb(2x512mb) 1t DDR620 /2.5-3-3-7
Printable View
guys, please keep silent.
Here (US) still under NDA :toast:
1.488v 3196mhz with Chilly 1 mod Mach II
1gb(2x512mb) 1t DDR620 /2.5-3-3-7
Onepagebook, hi, there is a 12V molex plug besides the chipsets, and a floppy power plug just besides the 4X PCI-E slot, I don't know what they are for, I plugged everything when testing. :D
I think one is for SLI power, just like Asus, but what is the other...? :D
Quote:
Originally Posted by TinTin
I never plug them in...:D
Oskar told me that just for enhance the power juice mombo "might" need.
It really doesn't matter. I don't BS. :D
OPB
whats is the black connections between the 2 PCI-X (16x) for?
They are sets of jumper to set SLI mode for SLI version,Quote:
Originally Posted by blass
1-2 PCI SLOTs PCI-E 4=X2 PCI-E 3=X1, PCI-E 1=X16, PCI-E 2= X1 CPU side
2-3 PCI SLOTs PCI-E 4=X8 PCI-E 3=NC, PCI-E 1=X8, PCI-E 2= X4 CPU side
:)
Plugged for more Overclocking..? :DQuote:
Originally Posted by Onepagebook
Quote:
Originally Posted by TinTin
I don't think so...:D :toast:
toss in a set of the illusive PC4800 sticks and a FX55? :stick: huh? huh? huh?...very nice example of things to come, any release date mentioned?Quote:
Originally Posted by Onepagebook
:banana: Give us some results, better than NEO4 ???
:toast:
With this board I wont be needing booster right? I'm tired of resetting cmos and tunning booster all the time
benchs now!!! ;)
I think the additional 4pin connector is when ya go over 4Ghz@2.1V :D
when will NDA ends?! :rolleyes:
2.6?Quote:
Originally Posted by Onepagebook
The first post on this page! ;)Quote:
Originally Posted by HARDCORECLOCKER
I am still doing test.
:D Hey OPB - found it - looking good and I know You're buisy but please,
please do a test on single phase.
Will be an importand decision for many people if to buy NEO4 or DFI NF4 and unfortunately there are not so many on cascades (including myself).
But I'm counting on You and as far as I can see You have nothing else to do but testing the whole day long :lol: - so I'm optimistic You'll do it also on single phase.
:toast:
I thought review boards were released on the 10th. Shouldn't NDA be up by now?
Ditto! :)Quote:
Originally Posted by naelq
Quote:
Originally Posted by HARDCORECLOCKER
that's single phase..
my cascade is at Chilly's lab for fix..
Chilly 1 mod's Mach II here
Cascade is not back yet..
http://img135.exs.cx/img135/5471/nf4dreniv7xt.jpg
Just looking at DFI LANPARTY UT nF4 Ultra-D it also has 2x16 PCI slots, so can you use SLI mode?
I think the only difference is the SLI Bridge is not included.
:D Very nice picture OPB - am I wrong or are You using only neopren for insulation? Or sealstring and neopren?
:toast:
afaik the difference is that the sli has 2 8x pegQuote:
Originally Posted by [ r2 ]
and the ultra has 1 2x and one 16x peg
Nope nVidia i putting astop to that with the next driver release =/Quote:
Originally Posted by [ r2 ]
Från anandtech:
"MSI confirmed with us that they are canceling their plans for an "SLI"-like motherboard based on the nForce4 Ultra chipset after pressure from nVidia to drop the project. But apparently, the newest NVIDIA drivers prevent this SLI hack from working. EPoX and DFI are both introducing boards using a very similar principle to MSI's DBS solution, but they both also face the threat of NVIDIA pulling the plug with next generation drivers."
:(
I think you neeed to plug the 4 pin Molex for going over 3.3v mem
There is a set of jumper if you want to use 5V rail for Vdimm, switching from 3.3V rail, then you can set as high as 4.0V Vdimm. ;)Quote:
Originally Posted by Zaffa
Beware of excessive heat of MOSFET when using 5V Rail for Vdimm.