Printable View
so basically its not worth the upgrade, unless u have a crap cpu so one that wont go as high.Quote:
Originally posted by [N8]
2040MHz was the max for 3DMark stable. I was hopin for more, but o well :)
My first impressions are that the chips runs about 10c+ hotter than the Palomino...and it costs about $20 more than the 1600+ pallie...OC's similarly, maybe a bit higher...but it comes factory unlocked up to 12.5X.
Its certainly worth the upgrade. N8's XP1600 processor is one of a kind, the two results shown so far indicate that 1950 - 2050 is the norm for these processors. Sys has ordered two for me, he'll post his results here too :)
I haven't determinted the absolute stable points for my chip but so far it looks like this.
def 1.50 - 1600mhz
max unmodded 1.75 1800mhz
modded 1.95 1940's
modded at my max balls 2.15vcore 2.0ghz
I'll post up a screenshot when i find the max stable point. So far temps are mid 40's. (prime95ing)
I finally put this chip into my 8K3A+. My max. Prime95 stable was 2060MHz at 2.1v. I didn't have any luck with 2.2v... I dunno if it's my cooling breaking down or just that this chip gets very warm at this voltage but it actually hurt my o/c.
I still don't think this is a bad deal for $75 delivered. I probably wouldn't replace a fleet of AGOIA or AROIA CPUs, but I would buy this one over those if it were a new purchase.
What cooling Jeff?
I kinda agree w/ Sinnah. Its a toss-up really. Cuz the Tbred costs more...but by the looks of it, u'll get right around 2GHz w/ good cooling.....which is not so guaranteed w/ the 1600+ Pallies. It took me 4 1600+'s to find one that would do over 2GHz :)
OK, got me one 1700+ TBred too here in Austria. :)
stepping is:
AXDA1700DLT3C 41xxxxxxxxx
AIRGA 0230MPM
tonight I will post results on watercooling. :)
(I have a good Palo in my rig now - so the TBred won't be much better IMO, but we'll see...)
Swiftech MCX462+T (air-TEC) and Vantec Tornado with some ducted cold air.Quote:
Originally posted by Sinnah
What cooling Jeff?
Goldlocke,
Let us know your results...mine were also on a water setup....mild one tho..no chilling :)
Just an update ... something died last night! no boot this morning :(.
It could be the kx7, could be the tbred, i dunno didn't have time to fiddle before work. Though with temps mid 40's i shoulda been fine right? :(
What voltage were ya runnin into the Tbred?
Mine's been taking 2.2v fine so far....and my temps were in the mid 50's....like I said, this chip runnin alot hotter than my Palomino(mind you...my temps are coming from the internal diode).
From your picture the chip does not have the L1's connected... how are these chips unlocked?
Quote:
Originally posted by [N8]
The best part is...these chips come unlocked from the factory :)
I'm not positive if _all_ mults are available...we will see ;)
Thanks for the quick results on the new 1700+ t-breds. Does anyone know if they are t-bred 'A' or t-bred 'B'?
The L1's are connected underneath the surface....hence why the L1's are "burned" on the Palomino's.
I'm 90% sure these are A revision Tbred's.
I'd be inclined to think these are rev a's.
I was only running 2.1v and the temps were reading low 40's. Prine 95 was stable for an hour before i went to bed.
Then ... dead. I really hope it's not the chip... But i doubt i can get another $60 refurb kx7 so that's a shame too. maybey i'll try an epox? :)
Quote:
Originally posted by docah
I'd be inclined to think these are rev a's.
I was only running 2.1v and the temps were reading low 40's. Prine 95 was stable for an hour before i went to bed.
Then ... dead. I really hope it's not the chip... But i doubt i can get another $60 refurb kx7 so that's a shame too. maybey i'll try an epox? :)
http://www.newegg.com/app/ViewProduc...tby=14&order=1
KX7-333R Refurb 55.00 in stock!!!!! GOGOGOGGOGOGOGOGOG!~!@#@$@#$@
:)
SWEET thanks man!
OK, ahm - its definetly TBred A. CPU Code 680! To end that discussion.
I'm testing now since yesterday. Hm,...it is certainly not that good like a XP2200+ :(
Yesterday it didn't want voltages higher than 2.05V. It wouldn't even boot into windows.
I have to sloooowly walk it up to higher voltages.
It does 1750MHz @ 1.5V max. It did 1850MHz only @ 1.95V yesterday :(
Today - after a 1833MHz@2.00V Burnin thru the night - It does these 1850MHz @ 1.75V @ 41°C folding@home :D hehe! 0.2V cheaper! :)
I think there is much more in this chippie, but I have to be patient and go step by step.
can it run prime95 or continuous 3dmark at 1850@1.75vcore ? F@H doesn't get it as hot.Quote:
Originally posted by Goldlocke
I have to sloooowly walk it up to higher voltages.
It does 1750MHz @ 1.5V max. It did 1850MHz only @ 1.95V yesterday :(
Today - after a 1833MHz@2.00V Burnin thru the night - It does these 1850MHz @ 1.75V @ 41°C folding@home :D hehe! 0.2V cheaper! :)
yes, prime95 ran ~ 1 hour at that setting. :)Quote:
Originally posted by seversphere
can it run prime95 or continuous 3dmark at 1850@1.75vcore ? F@H doesn't get it as hot.
So this chip isn't really worth it. Just wait until the price drops on the 2600+. :confused:
I dont believe so. The current market price for these is the same as an XP1600 in Aus. 1750mhz garanteed is very good for a Tbred, and 1800mhz @ 1.6v is also good for aircooled (aircooled, not those jet engine fans, and 6mm base copper heatsinks).
my first TBred AIRGA week30 TBred was a bummer! :(
I couldn't get it over 1915MHz by any means. It didn't like voltages higher than 2.03V.
so, I got me a newer one! :D
AXDA1700DLT3C 91xxxxxxxx
AIUGA 0235MPMW
-> 2083MHz @ 2,03V still testing...
-> look for AIUGA stepping!!!
Goldlocke,
Very nice OC there on that new chip! Wish mine clocked so well :)
Son of a §§§§§, 1 little letter between 1990mhz and 2100mhz :(Quote:
Originally posted by Goldlocke
my first TBred AIRGA week30 TBred was a bummer! :(
I couldn't get it over 1915MHz by any means. It didn't like voltages higher than 2.03V.
so, I got me a newer one! :D
AXDA1700DLT3C 91xxxxxxxx
AIUGA 0235MPMW
-> 2083MHz @ 2,03V still testing...
-> look for AIUGA stepping!!!