Mountain Mod Ascension "MMA"

current update for now:


my DIY lightning http://i919.photobucket.com/albums/a...SC_0310NEF.jpg

exterior look with fans
http://i919.photobucket.com/albums/a...SC_0328NEF.jpg
http://i919.photobucket.com/albums/a...SC_0376NEF.jpg

http://i919.photobucket.com/albums/a...SC_0336NEF.jpg
http://i919.photobucket.com/albums/a...SC_0338NEF.jpg

http://i919.photobucket.com/albums/a...SC_0391NEF.jpg
http://i919.photobucket.com/albums/a...SC_0387NEF.jpg
http://i919.photobucket.com/albums/a...SC_0386NEF.jpg
http://i919.photobucket.com/albums/a...SC_0385NEF.jpg
http://i919.photobucket.com/albums/a...SC_0378NEF.jpg

http://i919.photobucket.com/albums/a...SC_0400NEF.jpg
http://i919.photobucket.com/albums/a...SC_0404NEF.jpg

built without radiators until fermi is out
http://i919.photobucket.com/albums/a...SC_0406NEF.jpg
http://i919.photobucket.com/albums/a...SC_0407NEF.jpg
http://i919.photobucket.com/albums/a...SC_0425NEF.jpg


thats all for now untill I am done with exams in May. Hopefully, more updates will come in June.

I like the V8 backplate. Using it with my EK Supreme Tweaked (Matches the classy quite well).

I don't like how thick and uneven the EK is.

Quote:

---

Originally Posted by Wezly

I like the V8 backplate. Using it with my EK Supreme Tweaked (Matches the classy quite well).

I don't like how thick and uneven the EK is.

---

yeah, for me this is just temporary setup.;)

I cant wait my semester to finish so I could work on it.:)

Quote:

---

Originally Posted by marxviper

yeah, for me this is just temporary setup.;)

I cant wait my semester to finish so I could work on it.:)

---

Well, if you go EK for the CPU block, I'd suggest the V8 backplate over theirs.

Quote:

---

Originally Posted by Wezly

Well, if you go EK for the CPU block, I'd suggest the V8 backplate over theirs.

---

Are you talking about the one in the link below?
http://www.ekwaterblocks.com/shop/ac...-cpu-1366.html

Quote:

---

Originally Posted by marxviper

Are you talking about the one in the link below?
http://www.ekwaterblocks.com/shop/ac...-cpu-1366.html

---

No, that's better than the one I got. It's a multi-option.

In retrospect, I only didn't like it because I wasn't satisfied with the clearance the washers provided over the Intel required backplate, and the full-cover rubber spacer (same size and shape as the backplate) plus the counter-sunk screws made contact with the case, and I didn't want all that heat against rubber.

Quote:

---

Originally Posted by Wezly

No, that's better than the one I got. It's a multi-option.

In retrospect, I only didn't like it because I wasn't satisfied with the clearance the washers provided over the Intel required backplate, and the full-cover rubber spacer (same size and shape as the backplate) plus the counter-sunk screws made contact with the case, and I didn't want all that heat against rubber.

---

To be honest, if the cpu is cooled to 40 degrees at load, I dont think it wouldnt make any difference to the rubber.

I wish they could produce better looking backplate :rofl:

got new front panel. Here is the pic :)

http://i919.photobucket.com/albums/a...SC_0003NEF.jpg

ooooooh

nice build viper :)

thanks for your comments.

Any suggestion about the radiators combinations and how many loops should I consider as I am considering one GTX 480 and 12 GB dominator GT 1600 is welcomed at my thread.

Looking forward to your replies

Update:

Done with exams like a week ago, had good break. Now I am back working on my pc.

I got the following
BP fittings both compression and barbed with clips.
480 XPS Radiator
Asus GTX 480
EK waterblock for the motherboard and for the graphics card (including the backplate which is on the way)
Lamptron Fan controller
Couple of more Enermax fans


I want to paint the radiator and I got myself a sander. I do not know how to start with it. There are 80,100,120 grit sandpaper available with the sander I bought. I do not know with one to use. I checked the youtube and could not find the answer for myself.

Need help.

Are you going to wetsand the gloss on the radiator? if so I would suggest you want to get some higher grits aswell 1500-2000 range

@Oli4v
@Kibbler

Those are two gentlemen here who have sanded/painted rads quite well recently. I'd ask them if they don't stop by on their own.

Anybody else?

thanks Wezly, I already send a message to kibbler.

Quote:

---

Originally Posted by GJS1

Are you going to wetsand the gloss on the radiator? if so I would suggest you want to get some higher grits aswell 1500-2000 range

---

thanks for reminding me. :up:

Tell me which grit do you recommend me to sand the radiator?

Well I tried to paint my three radiators and here is the result: :(
http://i919.photobucket.com/albums/a...0000905NEF.jpg

Sanding was the toughest thing to do, I sand and sand even used sander, after sanding for long time, this was the result:

http://i919.photobucket.com/albums/a...0000870NEF.jpg

my EVGA waterblock

Wish they didnt have have put small red plexi, it took ages to put washer in the transparent plexi and screw it real tight. I hope it does not leak.
http://i919.photobucket.com/albums/a...0000889NEF.jpg

http://i919.photobucket.com/albums/a...0000900NEF.jpg

http://i919.photobucket.com/albums/a...0000901NEF.jpg

This one is ironic, I don't understand 2 circular ek stickers.
http://i919.photobucket.com/albums/a...0000902NEF.jpg

My GTX480 block with backplate:
http://i919.photobucket.com/albums/a...0000881NEF.jpg
http://i919.photobucket.com/albums/a...0000878NEF.jpg

http://i919.photobucket.com/albums/a...0000908NEF.jpg

Lastly, fittings (just few of them, too lazy):
http://i919.photobucket.com/albums/a...0000925NEF.jpg

Believe it or not but I kind of like this look.... Even better with a clear coated.

http://i919.photobucket.com/albums/a...0000870NEF.jpg

Such look would fit in some steampunk mod. :)

lol. I agree. Half way through sanding the radiator it looked good and I thought of leaving like that. Unfortunately, that was not the theme of my work.

It would look good, if my theme was for steampunk mod (like churchy mentioned)

As first time doing this work, now I know why people take their sweet time to make beautiful cases. This kind of work needs dedication for perfection, patience and lot of hard work.

Those stickers are for warranty verification. If your block leaks they want to know you didn't open it (even though you have to change out the red piece :D )

Quote:

---

Originally Posted by Wezly

Those stickers are for warranty verification. If your block leaks they want to know you didn't open it (even though you have to change out the red piece :D )

---

:rofl: thats what I meant. what if i messed up changing the red piece. I was :mad: when it came with red piece attached. In the picture it was with transparent piece.

Why do they let me down? :shakes:

BS. Eddy_EK has already mentioned few times, that those stickers mean "leak-pretested by EK", not "removing sticker voids warranty".

Then what's the one on the supreme for?

I planning to do hardcore wiring and sleeving for the fans.

I have a question about LED switch on enermax fans. I notice that there are two wires of different colors.

Is it possible to join the wires of the same colors and connect them to the switch?

Also, each fans have thermal sensor. Should I just cut the sensor off and join the wires together? sensor looks like two wires joined with melted pasted shaped like a bud

http://i919.photobucket.com/albums/a...0000970NEF.jpg