New Koolance CPU-360 Water Block!

I'd rather see the base without the finish as it doesn't require corrosion resistance.

One question Tim, how would you rate this with sub-amb or sub-zero flow compared to the EK Supreme HF?

Is it as restrictive as the CPU-350 was and when will it hit the stores?

Quote:

---

Originally Posted by ohms

Is it as restrictive as the CPU-350 was and when will it hit the stores?

---

Umm,

Quote:

---

Originally Posted by Koolance

The CPU-360 uses an advanced microfin cold plate-- 0.25mm fins, 0.30mm channels-- o-ring sealed impingement plate, and an optimized flow path to yield extremely high performance. This is done with much lower coolant restriction than the previous CPU-350.

---

Great looking block :up: Now is the time to find out: XT vs 360 :)

Lol, thanks Waterlogged, I must have missed that part in all the excitement and... ohhh shiny.

Can this block fit 3/4" OD Comp fittings?

Quote:

---

Originally Posted by Onoff312

looks great could use some black highlights.

---

Shhhh... you're stealing my ideas.

Quote:

---

Originally Posted by faster3200

Can this block fit 3/4" OD Comp fittings?



Shhhh... you're stealing my ideas.

---

Koolance says yes;

Quote:

---

Originally Posted by Koolance

Factotum beat me to it. That's it included with the kit. It will allow all of the same sizes of nozzles. The mounted picture I originally posted is with compression fittings for 1/2" ID, 5/8" OD. However, our 3/4" OD compression also fit with about 1-2mm to spare.

---

Ambients holding @ 20.2... water temp @ 22.1

San Aces @ around 1500 RPMS.

KL-350
http://i125.photobucket.com/albums/p...Temp/KL350.jpg

You guys like my lazy man OC???
Its called Ramp the Multi only.. :rofl:

Gonna flush the loop, and drop in the 360.
Should have results for it by 2pm PST today.

Guys my results are unoffical... meaning... it wont tell ya much besides is the block better on a high pressure system and on gulftown or not.

Also keep your eyes on realtemp and not cpu-z... :P
yes i know im teasing ya with a 980..

those are good temps for the k350.... :D

Quote:

---

Originally Posted by Hondacity

those are good temps for the k350.... :D

---

i think my sensors are borked again.

So all there good for is... very cool.. warm... oh noes its gonna pop!

NaeKuh
What does i7 turbo feature shows?

Quote:

---

Originally Posted by Factotum

NaeKuh
What does i7 turbo feature shows?

---

im on a E759 classy dude..

there is no turbo throttle on this board.

Also this is an XE cpu, and my multi is 32x... there is no turbo that will take you from 25x -> 32x unless its a XE cpu. :rofl:

Anyhow here is the KL360 temps..

They look a TAD bit better, but ambient are not working with me today.

So take this as a grain of salt... and wait for vapor or skinnee to show results.

KL-350
http://i125.photobucket.com/albums/p...Temp/KL350.jpg

KL-360:
http://i125.photobucket.com/albums/p...ance/kl360.jpg

The 360 does show as an improvement tho.
I would need to get multipul mounts down for it to be more accurate, which is why i am asking u guys to take this a a big grain of salt. :rofl:

Naekuh,
You have results with a full load?
How do you think this will compare against the swiftech?

I might be bugging you again soon for your help and advice...its finally time to go H20

send me a pm or I am always on the messenger if you still have me listed :rofl:

forgot to say that this is yet another Sweet looking block from Koolance:up:
I was going to get the K-350 a while back but never made it; this block IMO looks even better:up: :clap:

Which way do the pins run in reference to the top? Is it fixed or can you change the orientation? I thinking that if you changed to pins to run with the fittings, you can increase the flow and vice versa will increase the performance.

Quote:

---

Originally Posted by NaeKuh

KL-350
http://i125.photobucket.com/albums/p...Temp/KL350.jpg

KL-360:
http://i125.photobucket.com/albums/p...ance/kl360.jpg

---

Strange to see the GFlops so much higher on the 360 than the 350. Were there any changes other than the block?

--Matt

Hmmm...this just made my waterblock decision much more difficult. I'll wait for some benches. Nice work!

Quote:

---

Originally Posted by mattkosem

Strange to see the GFlops so much higher on the 360 than the 350. Were there any changes other than the block?

--Matt

---

no change... i noticed linpack varies as you run it...

But im also at a low bclk... if i ramp up bclk those numbers change a lot too.

But as i said, its a lazy man's OC.

Quote:

---

Originally Posted by NaeKuh

But as i said, its a lazy man's OC.

---

Like your avatar ? :) Anyway, great job mate :up:
Looking forward to xt vs 360 numbers.

I dont care how it compares, It will be better than the 350 and thats what I was gonna get last year; count me in on this one :up:

I love the way it looks, and I like the fact that its already setup for the different sockets.

Unfortunately I am a noob and have to rely on Naekuh's word :rofl:

I am sure this block, apogee Xt, and HK 3.0 will all be at the top of the list. I think it will come down to everyones final preference.

Quote:

---

Originally Posted by INFRNL

I dont care how it compares, It will be better than the 350 and thats what I was gonna get last year; count me in on this one :up:

I love the way it looks, and I like the fact that its already setup for the different sockets.

Unfortunately I am a noob and have to rely on Naekuh's word :rofl:

I am sure this block, apogee Xt, and HK 3.0 will all be at the top of the list. I think it will come down to everyones final preference.

---

Be careful with that, you'll spend WAY more $ than you ever intended to. :ROFL:

(deleted respecting skinnee, vapor, martinm and shazza)

Now, now, scamps - don't start the international wars :)

You know that NaeKuh's procedures are only representative of the Manga ways ...

@Shazza
You are right, sorry. Deleted :wave:

Quote:

---

Originally Posted by gillbot

Be careful with that, you'll spend WAY more $ than you ever intended to. :ROFL:

---

isn't that the truth, we don't want to be aigo'd, but I think I was the last time. Naekuh= 5 start budget/class

Gillbot/INFRNL= McDonalds or the buffet class:rofl:

These should be rolling out tomorrow, looks like they are priced at the previous K350 pricing; not bad, I have seen worse

i am not a tester..

which is why i am not claiming anything besides it being better then its predicessor.

i gave up testing when ES processors were ban'd.

That makes no sense to me, but my first love has always been processors.

So i decided to give up the later instead of the former.

is it better then the HK.. dunno.. is it better then the XT?
i dunno either..

is it better then the KL-350... well in my system it is.