Yea I'm sure they just glue the tag onto the PCB for ****s and giggles. Anyway here is a pic.
http://www.clanbbw.com/publicimg/dat...s/DSC00974.JPG
Printable View
Yea I'm sure they just glue the tag onto the PCB for ****s and giggles. Anyway here is a pic.
http://www.clanbbw.com/publicimg/dat...s/DSC00974.JPG
thats the old mcp350..that martin showed the modification on...
the thread starter's got the new pump... look at post #9 and #25 of this thread
**usps hasn't delivered my pumps..ordered it friday..sheesh
slow lol. how's the wiring look on your pmp400's? same as my mcp350?
Sorry I was replying to the OP since he asked if the pump in the link was moddable. I just received that pump from them less than a week ago and posted a pic up. Not sure how he got a different one when they were ordered about the same time.
pmp 400 (ddc 3.1?)
http://i24.photobucket.com/albums/c5...5/IMG_0179.jpg
mcp 355 side by side with pmp400 (ddc3.1?)
http://i24.photobucket.com/albums/c5...5/IMG_0181.jpg
That is a lot of pumps lol. I'll trade my 3.1 for one of your 3.2's ;)
i just received 3 pumps...all the pcb's are identical to the pmp400s...and like your ddc3.1 10w...
mine are labeled as 18w..i don't know what else could be seen..i'm studying the pcb UL or UR inscripted on it...dunno what they mean ...
ddc3.25 and pmp400 from the right...
**burninator...i don't know how you can mod that bitsch LOL
http://i24.photobucket.com/albums/c5...ity25/8888.jpg
:(. Since my 3.1 appears to be the same as your 3.25's how bout we just trade? LOL
Man this sucks... Now I'm stuck with a 10W pump...:mad:
Quote:
Originally Posted by Hondacity
i'm guessing you might have a ddc3.25 :up:Quote:
Originally Posted by Burninator
i'll monitor the rpm later...take note of your rpm too..lets compare numbers...
That would be nice. :D
Alright, I'll do that. Would it be ok to run the pump dry to get a RPM reading or should I set up a small loop?
you'll kill it :D
Lol. K.
Set it up and got a reading of 3900RPM, that good or bad?:confused:
they are identical right? so the pmp-400 is a 3.25 !Quote:
Originally Posted by Hondacity
BTW still no reply from Koolance :down: !!
@Honda: got any numbers? :shrug:
im setting up my scope...gimme 45minutes
my classified board ...reads 4550-4585rpm :)
Only posting pcb shots that have already been posted... will be running PQ in the near future.
http://skinneelabs.com/sample/Lab/th....2-3.25_01.jpg http://skinneelabs.com/sample/Lab/th....2-3.25_02.jpg
skinnee
do you have the 350?
nope, MCP355's and PMP-400. Never had the notion to buy the 10w version.
thanks
if you look closely at the PCB's... the traces are different.
The only difference I'm seeing between the OP's 3.1 and the pics skinnee and Hc have posted are the numbers on the sticker. . .and I've already stated that Laing has a long history of chaos in that department. :rolleyes:
Did you get a mano?Quote:
Originally Posted by Hondacity
Between your 355 and PMP400, yes. . .this is true. . .but between the PMP400 and the pic the OP posted of his 350, no.Quote:
Originally Posted by skinnee
I'm gonna be picking up a swifty 350 from P-PC's sometime soon and hope I get what the OP got, anyone know a place I can score a cheap DDC3.25 (let's say $65 or less)?
no mano...i'm saving up for a gtown :D
**wl
do you remember your rpm for the 355? was it around 4300?
In that case. . .Dead head Dead head Dead head Dead head Dead head :DQuote:
Originally Posted by Hondacity
I had to check my video because I'd forgotten and it was 4350 to 4380, so it's in the neighborhood.