Lapped core 2 duo IHS pics

Quote:

---

Originally Posted by virtualrain

I echo that question... The purpose of thermal paste is to fill the tiny gaps in an imperfect surface... With a finish like that, does paste help or hinder?

---

id also like to know.

Quote:

---

Originally Posted by virtualrain

I echo that question... The purpose of thermal paste is to fill the tiny gaps in an imperfect surface... With a finish like that, does paste help or hinder?

---

The funny thing is, unless the thermal paste is almost liquid, with a mirror-finish like those, the odds are you're actually ADDING imperfections... :lol2:

Would anywone be so kind as to shed some light on this subject? Maybe with some tests to back either conclusion?

And thanks for the reply about the warranty issue. I'm not going to try that with a 1 month old €200 E6400, I'll have to get a €50 Celly to do that :p: My money doesn't grow on trees (unfortunately) hehe

Cheers.

Miguel

MIRROR MIRROR ON THE WALL WHAT IS THE BEST FINISH OF THEM ALL

Cathar says 600grit :)

Think I'm going to try lapping my P4 3.2NW to get a feel for this before doing anything of value :)

Quote:

---

Originally Posted by rick_fx

Same here. Got a 10C decrease in idle temp and 5-6C got load temps on my e6700.

---

Without lapping, my E6600 is running about 5 deg higher than the room temp (idle). Now I wonder if I can get it to run 5 deg lower than room temp if I lapped it... anyone tried this? Please post your results ... lol :D

Quote:

---

Originally Posted by virtualrain

I echo that question... The purpose of thermal paste is to fill the tiny gaps in an imperfect surface... With a finish like that, does paste help or hinder?

---

Thermal Paste (a.k.a. Heatsink compound) is basically silicon grease loaded with some heat conductive substances - it is a reasonable conductor of heat but even the premium stuff (think nowherenear-Arctic-$$$ilver) is nothing when compare to the thermal conductivity of metals such as Cu or Al.

A small amount of Thermal Paste fills the void and get rid of the air in between the IHS and the HSF, creating a lower themal resistance than air (which is a bad conductor of heat). Too much of it is like putting resistors in series (because afteralll that stuff is not an ideal heat conductor). It creates a thermal resistance in between the IHS and HSF, so I guess you know what that means, right?;)

Quote:

---

Originally Posted by dinos22

MIRROR MIRROR ON THE WALL WHAT IS THE BEST FINISH OF THEM ALL

---

Yes you shall go to the ball cinders :D

@topic -
Seriously though lapping to a mirror finish is nice to look at sure, but really as long as the surface is flat that is enough, as dinos/cathar says 600 grit is plenty to achieve this without gouging the surface. To lap an IHS that is already pretty much dead flat is not worth it, but if your IHS is concave like mine was then chances are you will get a good result from lapping... sadly Intel's IHS's are not consistent in that regard so it's always worth checking.

As far as paste application, in my experience it pays to use as little as humanly possible, I've always had best results when the paste is so thinly applied that it is practically translucent. The method described by Arctic Silver where you apply a line for dual core or a grain of rice for single cores and then let the heatsink spread it always gives much worse results for me, it may be fine for the uninitiated, but when every last 0.1c counts it usually makes the thickness of the TIM way too heavy and hinders heat transfer. That's an interesting idea about not using any paste at all, I've considered it in the past but never had the balls to try it out... so far. :D

No polish whatsoever, just wet and dry, 30 minute job

http://img142.imageshack.us/img142/8693/xp90c2nd4.jpg

http://img137.imageshack.us/img137/4778/xp90c1rl3.jpg

http://img148.imageshack.us/img148/3...dconroegh6.jpg

Awesome pics lawrywild :)

I've never really considered the benefits of lapping, guess I'm like a boy with a new toy and want it installed and running as soon as poss but this thread has reminded that OC'ing is like decorating - it's all in the preparation, plus I've always been attracted to shiney copper :D

how's the warranty after lapping the processor?

tnx

Quote:

---

Originally Posted by DJSUB

how's the warranty after lapping the processor?

tnx

---

gone ... i believe ... :D

Quote:

---

Originally Posted by sbinh

gone ... i believe ... :D

---

and that's when you ask yourself how often do you have CPUs fail on you after a good 24+ burn in... the answer is close to never. About 1 in 10k are prone to fail.

Quote:

---

Originally Posted by HermS

Yes you shall go to the ball cinders :D

@topic -
Seriously though lapping to a mirror finish is nice to look at sure, but really as long as the surface is flat that is enough, as dinos/cathar says 600 grit is plenty to achieve this without gouging the surface. To lap an IHS that is already pretty much dead flat is not worth it, but if your IHS is concave like mine was then chances are you will get a good result from lapping... sadly Intel's IHS's are not consistent in that regard so it's always worth checking.

As far as paste application, in my experience it pays to use as little as humanly possible, I've always had best results when the paste is so thinly applied that it is practically translucent. The method described by Arctic Silver where you apply a line for dual core or a grain of rice for single cores and then let the heatsink spread it always gives much worse results for me, it may be fine for the uninitiated, but when every last 0.1c counts it usually makes the thickness of the TIM way too heavy and hinders heat transfer. That's an interesting idea about not using any paste at all, I've considered it in the past but never had the balls to try it out... so far. :D

---

well i dont think you have to worry about how big your balls are with trying out no paste. Personally i think now adays unless your stuff is extremely uneven as long as the metal of the heatsink makes good contact with the IHS you wont have to worry about starting the thing up and it burning up :rofl: I would know, when i first started building computers i did not mount a heatsink right on a slot 1 pentium 3 and it didnt make contact with the cpu, and i destroyed that cpu by always trying to run it with no heatsink :rofl:

Quote:

---

Originally Posted by rick_fx

Here is a good guide: :)

http://www.thetechrepository.com/showthread.php?t=71

---

Excellent stuff, thanks! I beeter think hard about this, cus even though CPU failure is very rare (I have never needed to RMA a CPU) it is still a possibility. Im nervous! Still, great stuff, everyone! :clap:

Well, you guys got me so excited by the pretty lapping jobs, I had to try for myself.


http://www.pbase.com/eltonandersen/i...3/original.jpg
http://www.pbase.com/eltonandersen/i...7/original.jpg

so how uneven was it, im sure you were able to tell during the process? My lappiing kit is on its way, but ill be lapping my old AMD athlon 64, because i wont be buying the new parts for the new rig for some time.

It took me 20-30mins of sanding just to get the inner area at the same level as the outer area. It was like a crater in the center.

Wow! Loved the "out the window, on the street" pic, haha! I didn't spend too much time on this E6400, but it did lower temps and she's 24hr Orthos stable @ 3600. :)

http://img.photobucket.com/albums/v2...0/IMG_1138.jpg
http://img.photobucket.com/albums/v2...0/IMG_1142.jpg

whats the best motion to go into?

90 degree angles or a figure 8?

By 90 degree angle, what i mean is to place the cpu on the sand paper and move it up, straight up then pick it up and place it back down in the center of the paper and do it again at least another 4 times. Then rotate the cpu to the right and go up again 5 times. Is this the best way?


also, you have to do this dry right? Do not wet the paper with anything??

Quote:

---

Originally Posted by Orangeblast

whats the best motion to go into?

90 degree angles or a figure 8?

By 90 degree angle, what i mean is to place the cpu on the sand paper and move it up, straight up then pick it up and place it back down in the center of the paper and do it again at least another 4 times. Then rotate the cpu to the right and go up again 5 times. Is this the best way?


also, you have to do this dry right? Do not wet the paper with anything??

---

Read this, same principle applies for a CPU as a heatsink. http://www.bigbruin.com/reviews/lapp...dex.php?file=1

love this thread ... awesome pics ... hmm .. im thinking of lapping mine now as well :)

need more Mhz :)

It said to use water.

I think thats a no-no.

you sand the IHS with dry sand paper, NO WATER no OIL no soap. right? just straight dry?

and yes, it looks like the 90 degree up/down left/right technique is best.

do you do it back and forth or up and the lift up and place it back down and go up again?

My E6300

http://upload.nickfire.com//files/13...nroe%20008.jpg

Reflecting camera.

http://upload.nickfire.com//files/13...nroe%20014.jpg

Reflecting the Giant Markets logo on a gallon of distilled.

...and my friends Celeron D

http://upload.nickfire.com//files/1/...ebay%20013.jpg

Reflecting my monitor.

http://upload.nickfire.com//files/1/...ebay%20018.jpg

and mousepad.

<3 u for this thread.

h8 u for using this cute avatar i allready use in another forum.

h8<3 :D

:rofl: