Good review and pics, Thanks!
Printable View
Good review and pics, Thanks!
weird..where's this 10 bios?does it supports e6400?
i still can't use the 533 and 667 dividers even with 213 :(
1070 was on Asus web site before (mine came with it) but asus deleted it. Don't know why since it's still the most stable bios for non conroe cpu.
for conroe, you have a ucode error at start.
i had that ucode crap too with the bios onboard..but no biggie since it works fine :)Quote:
Originally Posted by Vric
What are the chances of this thing taking a 6300,6400 to 3G;s?
with 6400 fairly good. with 6300 it would be hard.Quote:
Originally Posted by GOATSLAYER
I have seen some people hitting the 400Mhz limits, but I have seen some people hitting a wall at 370Mhz fsb. (but it was 4mb conroe)
E6300 is impossible to hit 3G with a 400mhz limit. E6300 has a multi of 7X so max it could hit is 2.8ghz which aint bad. I could not run it stable at 2.8ghz so I went down to 2.6ghz as I mentioned before. Now that my AS5 paste has settled I noticed nice temp drops and I'm at 2.7ghz stable after burn in and running dual superpi. I used vcore of 1.4 and shows 1.37 on probe. The best is to use the lowest voltage you can to run stable as it affects your temperatures greatly with this cpu. At 2.8hz when I did a burn in with sisopht though its alarms went off at 60c. I touched the HSF at 50c and higher and it feels luke warm. If that is the case then it is the NB that can't handle the higher speeds and it's not because of cooling (since I used a fan+as5 on my NB it also runs cool to the touch).
If they don't raise the fsb to 500, when I want to upgrade in 2 years I'm not sticking anything faster than a e6800 in this board, Ide rather get a new mobo.
New 0309 Bios
ftp://ftp.asus.com.tw/pub/ASUS/mb/so...B/P5B-0309.zip
P5B Release BIOS version 0309
1. Fix SATA configuration select disable and compatible mode will show SATA3 and SATA4
2. Show some memory spd items to improve overclocking ability.
3. Enhance overclock capability above FSB 500
4. Support jumperfree FSB to 650
5. Add auto calculate DDR frequency rule to display DRAM frequency
6. Support Conroe CPU ratio adjustment
7. Fix system fail to POST after crash free or EZFlash when using particular XE CPU. (Note: System will still boot after performing clear CMOS)
8. Fix some ODDs fail to read files from CD under EZFlash2
9. Enhance performance with NVDIA VGA cards
10. Support AiGear for Presler 3200 c1 stepping CPU
11. Revise NOS table for conroe B2 stepping
12. Support FSB533 CPU over 3.4GHz frequency under AIbooster
13. Fix AI Gear fan speed too low sometimes under normal mode
Tried the new 0309 bios and had huge problems with random reboots. Never got a chance to really play with the expanded options because windows kept locking up/rebooting every 10-15 minutes.
oh it's here
i'll try it later
tnx:)
New Bios screen:
FSB up to 650Mhz (also note auto calculation memory)
http://www.magietec.com/computer/bios6.jpg
FSB Termination Voltage raised from 1.3V to 1.45V with more options
http://www.magietec.com/computer/bios5.jpg
Lot more SPD settings.
http://www.magietec.com/computer/bios7.jpg
Also note, this bios have the same problem as the 0211 and 0213 with 533Mhz fsb CPU (Celeron and 805) Overclocking is simply impossible or very unstable (I was able to boot half of the time at 150Mhz fsb with USB legacy off.. With 0170 bios it work perfectly up to FSB 190Mhz) Divider don't work either. (they are available starting 150Mhz, but if I choose DDR600 for example, I simply won't boot.)
I wrote to Asus about the problem with 533Mhz CPU, they offered me a new Bios chip (which isn't even swappable on this board) They simply don't care and don't know what we are talking about.
I'm running this Bios right now, but my CPU is at stock.
uhm nice..more volt on fsb too..lol i like now the ram settings more stuffs :D
wow finally more timings to play with!
If someone with Conroe could try it, I would be useful. I can't do more with my Celeron.
I might flash back to 0170 since it's the only bios that allow me to overclock. (even 135Mhz is unstable with other bios)
Anyone encounter problems yet? I'm 2 hours into dual priming my previous stable 24/7 overclock on the 0213 bios so I'm reasonably convinced that the bios flash was the source of the reboots. Are there any outstanding problems with Team's new memory that I ought to know about (perhaps one of the newly tweakable timings/settings causing problems)?
well atleast now i can finally boot using 1:1 :slapass: :toast: :banana:
going to do 2 32mb spi now then ill go higher :)
http://img344.imageshack.us/img344/2783/newbioshg0.jpg
Post your result soon :p:
Quote:
Originally Posted by Vric
wait i had to increase my vcore :slap:
:woot:
for now i did this lol
going to do the 32mb now
http://img180.imageshack.us/img180/5646/17sdj9.jpg
weird so it wasn't the vcore too low..it's still giving me error at 400x8 same settings changed vcore only
Have you changed any of the additional memory timings in the new bios? I guess my case is isolated if you aren't experiencing any trouble. What kind of video card are you running and do you have any additional pci cards? Do you have usb legacy support disabled?
update increased to 1,4 fsb and moved from 400 to 420fsb now
:slap:
live update :toast:
http://img148.imageshack.us/img148/3996/420lc6.jpg
no..i'm using x1800xt 512 and running a dvb-t(digital tv card pci) and no usb legacy support is on :cool:Quote:
Originally Posted by Professor12
here it is passed with no problems :)
going to test higher and higher now
http://img147.imageshack.us/img147/4066/4202nf6.th.jpg
running 1 32mb spi at 450x8 now
http://img503.imageshack.us/img503/8713/4501vg5.th.jpg
now i can finally say..i'm having fun with this new system 32 is still going..don't look the result of spi..i'll do it just to see if it's stable