nice stuff ccokeman. YOur RAM looks sweat!
Printable View
nice stuff ccokeman. YOur RAM looks sweat!
Unfortunately its on a divider. 180 divider gives me 259 fsb. Mine maxes at 265fsb.
http://valid.x86-secret.com/show_oc?id=86691
This is temporary ,need to tune my vapor/phase cooling better :brick:
But for now i am running it om 3.1ghz daily :)
Damn, that's sweet for a Toledo, they don't usually like cold. Stepping?
ccbwe 0528 cpmw
batch nr 0157
haven t found any coldbug yet :D
Hi, Im kinda new to these forums, but been about searching them for answers for a while, hopefully someone can answer this one for me.
I currently got an AMD Athlon X2 3800+ @ 2.8ghz @ 1.5v, this is an 0601 CPU (dont ask me for the rest of the stepping as its got a water block on top of it) but when I first got it, I remember looking the full stepping up and seeing people hit 3ghz with this CPU.
Its plugged into a DFI expert AA0 mobo with 2gb G.Skill HZ PC4000 currently at 264mhz, set to 180 in the bios, if I set to 166 I get no post.
I can get this CPU to 2.9ghz @ 1.57v 1hr Prime stable but then fails every time, I thinks its a memory thing as the memory is some what of a BIEACHHH to configure.
Any help on this would be greatly appreciated.
X2 3800+ LDBHE 0605 GPMW
290x10 290mhz
Thermaltake BigWater SE
Temp: 30/43 (idle/load)
Bios 04/06/2006
VID=1.52v
VID SPECIAL=Auto
CHIPSET=1.2v
LDT=1.5v
LDT=3x
FSB/DRAM: CPU/12
CPC =Enabled 1T
CAS Latency(CL) =3
RAS to CAS(Trcd) =3
Min RAS# Active time(Tras) =5
Row Precharge Time(Trp) =2
Row Cycle Time(Trc) = 7
Row Refresh Cycle Time(Trfc) =13
Row to Row Delay(Trrd) =2
Write Recovery Time(Twr) =2
Write to Read Delay(Twtr) =2
Read to Write Delay(Trwt) =3
Refresh Period (Tref) =3120
Write CAS Latency(Twcl) =1
DRAM Bank Interleave = Enabled
Skew =Auto
Skew Value =0
DRAM Drive Strength =Auto
DRAM Data Drive Strength =Auto
DDRAM Response Time=Fast
Max Async Latency = 9
Read Preamble Time = 5
Idle Cycle Limit =256
Dynamic Counter =Enable
R/W Queue Bypass =16x
Bypass Max =7x
32 byte Granularity = Disabled
http://img96.imageshack.us/img96/824...ark10vh.th.jpg
CPU-Z: http://valid.x86-secret.com/show_oc.php?id=90382
Well so far it's superpi + 3Dmark05 stable, I will post more benchmark later :D, just too happy right now since I thought my CPU maxed @ 2.66Ghz, found out that was because of the max async latency and read preamble set too low :D
@Seanie's snow: You could try lower the max async latency and read preamble like I did, I thought it didn't matter since my Ram can run stable @ 250Mhz but putting mem divider makes it unstable even when the RAM is running lower than 240Mhz.
http://valid.x86-secret.com/show_oc?id=91846
Using a VapoLS - Had it running like this for about 3 months now. Still a lot of room for improvement but its 100% stable atm.
Vcore 1.472
This is my first post in Xtreme
http://vicentk.no-ip.org/compter/A64_260x10_1.520v.jpg
Maybe it is a little OT.. but
What are the bests 2-3 steppings right now for +3800 X2? I saw the "database" of the first post but it doesnt have enough results..
And other question..the steppings of the opterons DC and the X2's are comparable? If in opterons a 0605 (for example) one is the best, in X2 should be good too?
Thanks :)
I've just received a new 3800+ X2. Is a manchester core 0605DPMW
When arrive at home will test it ejjeje
salu2
LDBHE 0601TPBWQuote:
Originally Posted by ZeroX
LDBHE 0601XPMW
From what i've seen, a good week for Opterons dual cores is also a good week for X2s. These weeks do NOT translate for single cores.
Only real example i can think of was 0548... 165s and 3800+ X2 both well above average.
-----------------------X2 3800+ air cooled --------------------------------
X2 3800+ LDBFE 0609 XPMW
280x10 2800mhz
Mobo---DFI NF4 Ultra-D
air cooled with Thermaltake Big Typhoon
OS---Windows XP Pro x64 Edition
http://i12.photobucket.com/albums/a2.../cpuzvalid.jpg
http://i12.photobucket.com/albums/a2...e/cpuzqmc2.jpg
I havn't gone any further yet as i wanted to get crunching ASAP :D I'm sure the chip has more in it, do i need dual SPI 32m to get on that leader board thing?
cheers, Ed
Nice. That's what I should be doing. What vcore did you have at 2700?
0601 Rocks:woot: Got this baby one week already and let it bruning in @ 270x10 with default voltage for the time being. Now it's time to go high :cool: . It seems there were still some more headroom to go with :bday2: but need H2O badly to cool this baby down :slap:
X2 3800+ LDBHE 0601XPMW "T" chips
290x10 290mhz @ Tower 120
DFI NF4-D Bios 03/29/2006
VID=1.5v
VID SPECIAL=Auto
CHIPSET=1.3v
LDT=1.6v
LDT=3x
http://valid.x86-secret.com/show_oc?id=93079
:) nice chip
An interesting Toledo X2 3800+ from 2006 (LCB1E 0618)
X2 3800+ @2900 1,47 vcore // 2x1Gb "bad" Gskill ZX @207 2-3-2-5
http://img455.imageshack.us/img455/8...29004au.th.jpg
The CPU-Z validation is a "bit higher" than the (up to now) tested stability :
http://valid.x86-secret.com/show_oc?id=97954
:D
what cooling?
My old LDBHE 0601 UPMW was a wee bit better than that on water, but still, it ain't bad, and if it's air that's quality.
Watercooling :rolleyes:
I could not find a LDBHE 0601 around here...and this one was an OEM I got to setup a rig for a friend..so I (he) cant complain :D
Same ask here for the X2 3800+ looking on some new thread i have see some X23800+ do easy the 3100mhz on water ->3200mhz.. i can have some with the revsion 0614 ( need verify the other part) Something about this one?.
is all new revision between 0606-608 to 0618 are fine? ( it's the 2 revision i have find with good OC..)
X2 3800 Manchester LDBFE 0614 WPMW
Asus A8N32 SLI-Deluxe (and DFI Ultra Infinity used in the SP2004 Screen shots)
Leadtek 7800GTX 256MB
2x 1GB Corsair VS400
Thermaltake Blue Orb 2
4x Seagate 300GB Sata2
http://www.users.on.net/~bugeyes/ind...900mhz_002.jpg
http://www.users.on.net/~bugeyes/ind...900mhz_001.jpg
http://www.users.on.net/~bugeyes/ind..._WPMW_010A.jpg
http://www.users.on.net/~bugeyes/ind...005%20copy.jpg
anybody seen these yet? LCB1E 0619 RPMW?
dave
X2 4200 Manchester LDBHE 0550 SPWM
DFI Ultra-D
BBA x800pro
2x 512mb Centon pc4000 2-2-2
6002-64 water
2x Maxtor 200gig IDE's
2900 290x10 1.568v
idle : 24-28 (depends on temps)
load : 34-38 (depends on temps)
http://www.sourcekills.com/albums/Th..._10_1_568v.png
suicide on water
http://valid.x86-secret.com/show_oc.php?id=93275
dice soon
nice chip :)
what's the tcasemax ?
67ºC its a T chip too
http://www.sourcekills.com/albums/Th...1344.sized.jpg
right after the decapping
Guys, what's about Toledos of 0601 (4400+). Won't it be a mistake for me to take one? As far as I understand, those few weeks (before NewYear and after) were devoted to the selection of best chips for FX-60? Am I right? The cause of my disturbance is that I won't have the possibility to exchange the sample. While I hope to get 2.8GHz on my LanParty NF4 SLI-DR
update on my X2 3800+ LDBFE 0614WPMW
http://i3.photobucket.com/albums/y90...rime3800x2.jpg
wr prime it is sure hot this time off year
http://i3.photobucket.com/albums/y90...r/DSC08044.jpg
setup like it looks now
http://i3.photobucket.com/albums/y90..._ripper/26.jpg
little pi run under mach2
http://service.futuremark.com/compare?3dm05=2099823
3.3ghz @ 1.71vcore
thats for now
just got a new x2 3800 LDBFE 0608 RPBW, hope this one is a goodie.....hopefuly ill have it up and running by the weekend, just waiting on the egg and atacom to ship my new hardware
I just got a new 4400.
These are the specs:
CCBWE 0609 DPMW
Batch C 60341
Do you have some informations about the stepping ?
http://valid.x86-secret.com/show_oc?id=108682
http://www.xtremesystems.org/forums/...16#post1615316
Max so far was 2850mhz benches shown in link. Will try to get a validation of the suiside 3ghz shot again. Stupid Cpuz cus it was out of date the 1st time.
well i picked up a cheap 4800
http://valid.x86-secret.com/show_oc.php?id=108860
ccbwe 0602 bpmw
stable at 2.92 gig @1.6v ihs removed under water so far 4 hours.
i needed 1.64v for a 3g ss,i cant get it stable at all.
I have the same stepping and I'm curious as well, although after a systool find max FSB run it seems to top out at 2500:mad: even with LDT = 3, VCORE 1.45, and 1/2 divider...strange thing is SYSTOOL also crapped out at 2500 with stock VCORE, LDT = 5(?), and a 1:1 divider:confused:Quote:
Originally Posted by Shakermaker
I'll be back later, I only spent about 1.5 - 2hrs poking around.
Quote:
Originally Posted by h@RRy
I have the same stepping...and mines crapped out at 2475....i think i can do 2500 but the temps got really high.. 52 or so...what are your temps?
X2 3800 Toledo:
ADA3800DAA5CD
LCBIE 0618EPMW
Vcore: Auto (BIOS)
http://img465.imageshack.us/img465/8...312vzo7.th.png
:slobber: 2.8ghz at stock volts 1.35v?? Is that the real voltage?Quote:
Originally Posted by davidian
Picked up X2 4200 for $185. LDBFE 0619WPMW Seems about average. 2.7ghz @ 1.485v Runs hot though, I might have to take off the ihs. With a big typhoon, I'm getting temps in the mid 50's. Probably could get 2.8 with more volts. Still, I'm happy with this, been running rosetta for about 10 hours now.
Yeah, it's real voltage. We have three CPU's from LBCIE 0618EPMW series (forum.purepc.pl), and each do 2800Mhz @ ~stock voltage.Quote:
Originally Posted by Tictac2
Yeah, BI mem controlled x2's are good to date :banana: 0621/0625 VPMW & WPMW's are also pulling the same results.
Got a LCB1E 0619 RPMW @ 2.75Ghz stock voltage for now.
Heres the beginning of the initial 2.7Ghz run, 10 mins after it was installed :D
http://img206.imageshack.us/img206/9775/sdyf6.th.jpg
Will update you guys with the max I achieve once new PSU etc arrive.
BTW, I would be interested to know the TCaseMax for the cpu's you BI guys have :toast:
2.9Ghz @ 1,36v
http://img272.imageshack.us/img272/3...360vfh4.th.png
Sorry for my noobiness:slap: but will a LCBIE 0618RPMW be the same?Quote:
Originally Posted by davidian
Pretty close.Quote:
Originally Posted by Tictac2
Counter CD has one, pulling fairly similar results. He got up to 3.1Ghz. (Link)
I have mine all up to 2.9, but for an everyday overclock i settled for 2.7, even though i can have it at 2.8, but i do believe it will only last 50% of the time if i stick it on full throttle 24/7 :slapass:
I have mine all up to 2.9, but for an everyday overclock i settled for 2.7, even though i can have it at 2.8, but i do believe it will only last 50% of the time if i stick it on full throttle 24/7 :slapass:
I got one yesterday from MicroCenterQuote:
Originally Posted by davidian
LBCIE 0618EPMW
batch 0686
2800mhz@stock volts 3hrs+ dual prime so far :banana: :banana: :banana:
1.575@ 3000mhz core1 craps out ~40 minutes dual prime, Core0 still going strong there:fact:
http://img169.imageshack.us/img169/8...3hrswt6.th.jpg
:toast: :banana:
Just got a LCBIE 0618RPMW x2 3800+ from eBay (for less than what i would buy for it from a shop :) ) so am hoping for great things. ..
These steppings seem to go incredibly far on stock volts, but then not as further as one would think on more volts. . ?
I'm thinking that it should work well with RMClock. . .becuase of the low volts.
(It works well with my 3500+ Venice - 230mhz fsb, x11 multiplier. Down at 1.4ghz when I'm not doing anything intensive and then it ramps up to the full 2.53ghz when I do. IMO, every overclock on stock volts should be teamed with RMClock, I can't see any disadvantage with it.)
I've just bought a Scythe Ninja Plus so I'm hoping that will work well with it.
Does this make the list? On air.
http://img341.imageshack.us/img341/7...board01go3.jpg
LBCIE 0618EPMW update
on air, TTBigTyphoon, ihs still intact:
SP32M@3000mhz
http://img20.imageshack.us/img20/895...p32mxy9.th.jpg
http://valid.x86-secret.com/show_oc?id=110261
SP1M@3100mhz
http://img191.imageshack.us/img191/5...sp1mcp7.th.jpg
http://valid.x86-secret.com/show_oc?id=110263
Well I am extremely dissapointed on my new purchase =(
I recently got a 3800X2 939 Manchester
0623 XPMW not sure of the first 5 letters but its the common ones on here...
Im pretty sure this chip sux and I really wanna exchange it grrr....
its not stable on anything above 2400mhz right now...it takes 1.47 to do that even stable. I tried 1.38v at that speed but BSOD with prime runnin both cores =(.
I verified it wasnt my HTT limit on board, cuz I lowered multi and ram and cranked the HTT to 280+ and I know it does 295mhz with my single core 3000+
I know the drivers are installed correctly I did it per recommendation of first post in this board. I also correctly switched HAL's to ACPI Multiprocessor in device manager. I know it aint that, thats causing the problem...that would be even if it werent oc'd.
My RAM I tried both auto settings and manual settings all below 200mhz...
It wont even do 2.55ghz @ 1.52v =(
My temps are 35C Idle @ 2.4ghz 1.47v load they approach 50C
My motherboard is Biostar Tforce6100-939
Im so pissed ... anyone have any ideas?
Thinkin about just putting my 0517 3000+ APAW back in here which can run 2.66ghz on this board just fine!
HELP!!!
AMD X2 3800 Manchester core
ADA3800DAA5BV
LDBFE 0609XPMW
Liquid cooled - 2800mhz (vcore:1.456v)
http://img82.imageshack.us/img82/443...temsfa9.th.jpg
Work-in-progress
:rocker:
AMD X2 3800 Manchester core
ADA3800DAA5BV
LDBFE 0626 EPMW
So far 250 default prime 1h.....
http://img67.imageshack.us/img67/953/img0804ee0.th.jpg
Seems nice enough :) . Almost the same stepping that I'm going to buy: LDBFE 0626GPMW. Keep us updated :fact:Quote:
Originally Posted by TEDY
which vcore you guys reporting, the one in bios or cpu-z ?
update : 2600 2h prime stable at 1.36v....
update 2 : 2650 prime stable 2h 1.36v ;)
Having some fun her
http://valid.x86-secret.com/show_oc?id=117133
more to come
Here is mine :
4000+ AM2 Windsor : 3000Mhz stable :) Vcore = 1,55V
and WR @ 3147Mhz :
http://valid.x86-secret.com/show_oc.php?id=118140
Mobo : M59SLI-S5
:D Happy here in france !
Here is mine,
http://fabian.bricard.net/images/3800.jpg
255x10 @ 1.31v (default) w/ XP90
Will give it a day or two before cranking in the volts.
Hi
This is my first overclocking at my new DFI board
I hope this isn't bad
http://members.inode.at/s.amidzic/DFI2.jpg
any reason you're running a 9x multi?Quote:
Originally Posted by Dede99
The reason is that it stay's stable at 9 the board wan't let me go up at multi at 10
How do I get the black windows taskbar?
Any stepping info?Quote:
Originally Posted by Dede99
Are you also aware that board shows the wrong VCore readings? More info here.
Just thought I would make you aware to reduce the likeliness of a blown cpu as I also own the same board on another system.
Looking good though :)
i hope this help's
http://members.inode.at/s.amidzic/DFI002.jpg
Here's mine. AMD 3800+ X2, LDBFE 0609XPMW. Running on AIR, using Zalman CNPS7000B-Cu. Running 2.8Ghz on VCore @ 1.44v with 2GB Memory @ CL2.5-3-3-6, 1:1, 2T (4 x 512Mb GSkill + Patriot-TCCD) RAMs.
- CPU-Z
- SuperPi 32M in various stages:
http://img84.imageshack.us/img84/669...hz01ve2.th.jpg http://img85.imageshack.us/img85/102...hz03gy8.th.jpg
http://img154.imageshack.us/img154/9...hz04bv6.th.jpg http://img146.imageshack.us/img146/5...zfindr5.th.jpg
Quote:
Originally Posted by dave_graham
just got 2 3800+ X@ from dave few hours ago
installed mine and booted up with teh settings in the screenshot below :woot:
it is
ADA3800AA5CD
LCBIE 0619RPMW
volt in bois 1.35v
http://img174.imageshack.us/img174/9437/2pj3.jpg
AMD X2 3800 LDBFE 0608RPMW @2600MHz 1.5V using XP-120 - 260x10 2.5-3-4 OCZ Platinum.
Oscar
This is my first OC, and here is what I got. I have my X2 3800+ running at 2.6ghz with 1.45v and HT 4x, idle temps of 31C-33C and max temps at 44C-45C, using a Thermaltake Big Typhoon. Still trying for 2.7ghz stable.
Just hit 2.7ghz, it is topping out at 53C-54C at full load. Is that a decent OC? 700mhz at just over stock temps?
EDIT: AAAARRGGGHHH!!!! My PC froze! 2.7ghz is not stable for me, looks like 2.6ghz is my limit.
I have mine to @2.7GHz to 1.55V.
Oscar
I had mine at 1.45v @ 2.7ghz, do you think upping the voltage might help make it more stable? It was at 54C, so I can't do too much more with it, but do you think upping it from 1.45v to like 1.5v would make it stable?
Of course! My X2 is fully stable 10h primer95 stable. ;)Quote:
do you think upping the voltage might help make it more stable?
Oscar
I'm at 2.5 Ghz 1.328v (board undervolts from stock 1.35v)
X2 3800+ Manchester
LDBFE 0621 GPMW
Running 260x10 @ stock volt(cpu-z 1.31vcore)
Noctua NH-U9 with Zalman 92mm 53cfm@7v Idle 27-28 Load both cores 38-39
Prime stable, but fails to load win @ 270x10. Havnt tested it more than that, Im in the middle of moving :D
Ok, so you think that if I up the voltage from 1.45v up to 1.50v it will be stable? I will try that out later today. If I can get a 700mhz OC that would be great. As of now I am already at the levels of an X2 5000+, so I am already saving like $350 just from overclocking. If I can get 2.7ghz and still stay at under 55C that would be sweet.
Although at 2.7ghz @ 1.45v it was hovering around 54C when it crashed, but it was running for about 30min-1 hour so I might be able to keep it arouind 55C if I put it at 1.50v. And just for the record these temps are using speedfan, but from what I've heard speedfan is very accurate. Ok, I have it at 2.7ghz, 1.50v, and HT 4x. Lets see how hot it gets.
Ah man, I am not liking this. It is at 57C and rising. Is that something to worry about? I heard that 60C is the absolute limit, is that true?
Your computer will shut down if the cpu gets to hot, AMD has a built in security. BUT I would think about all my other settings before raising the voltages on cpu more, cause at 1.55 there are reported deaths, so unless you have phasecooling or waterchilling, I suggest that you lower it to 1.525 or lower. I'm able to run my x2 3800+ at 2.85ghz at 1.45 volts, so you understand why I think your volt is high? :) Lower the HT to 3X, Set the ram divider to 166/333, and cpu multi to 9x and you can push your cpu higher if your motherboard is up to it. Mine is stable even over HTT 300..... last overclock I had stable was this.... :Quote:
Originally Posted by Brutus013
CPU 2.75 GHZ, RAM 500 MHZ, HTT 305(!!)MHZ (You may now HTT as FSB, but AMD has HTT, NOT FSB), and then all settings was set like above here again. Good luck! :banana:
My RAM is good for as high as I can OC, DDR400 at 333mhz. If I lower the HT to 3x won't I then have to OC higher so that my performance doesn't drop? Or is the performance from HT 3. the same? I am at 1.50v, not 1.55v. I will try HT 3x at 1.475v and see if the performance is the same.
I can't get it to boot at 1.45v no matter the settings. I don't know why. I have it at 1.475v and it is good. I can't even get it to boot at 2.8ghz though. I tried 1.50v with HT at 3x and it didn't boot. 2.7ghz is my limit.
It just may be the stepping on your cpu won't allow you any higher, or your motherboard won't overclock as good. Try setting your ram to 2T and see if you get any changes, I've noticed something about my power supply, when I have more than two harddrives plugged in I am more limited with my OC, but if I only have one or two harddrives, everythings fine. Not enough amp's I guess. Only a peak of 31 amps on two 12volt rails. 29 amp stable, 31 peak. So I guess I'm living on the peak! :woot:Quote:
Originally Posted by Brutus013
As long as you don't drop down to 5-600 mhz on your HT (hypertransport) you won't "feel" any difference. Your cpu only handles 1000mhz anyway, so 8-900 mhz is fine here. HTT * HT MULTI = HT FREQUENCY. So - HTT 280 MHZ * HT MULTI 3X = HT FREQUENCY 840 MHZ ;)Quote:
Originally Posted by Brutus013
CORRECTION: CPU handles hypertransport of 1000mhz EACH DIRECTION AT THE SAME TIME, so when I set it to 840 mhz it will go 840 * 2 = 1680 MHZ, but it will say 840 anyhow in cpu-z or any other program you use :)
My 3800+ (0618BPMW) runs at 2800Mhz (10x280) with 1.392V. RAM-frequency: 255Mhz.
http://img143.imageshack.us/img143/3120/2800cc5.jpg
Half an hour is missing on one core because i was using the webcam with my gf :bounces:
lcbie 0627tpmw
it's now dead and i'm waiting for a new lcbie chip. i hop it'll do better results
all under freezer 64 pro
http://starostise.free.fr/overclocki...z_1.23vmin.JPG
http://starostise.free.fr/overclocki...z_1.28vmin.JPG
max htt
http://starostise.free.fr/overclocki...MW/max-htt.PNG
max screen
http://starostise.free.fr/overclocki...W/cpu-3428.PNG
You are hoping for better results? sry but don't be greedy ...
i know :D
3.2Ghz insane for 1.35V. if overclocking is you hobby (like mine), i understand you, but if i had a cpu that is under de 1% of the best 3800+, i would be very satisfied.
if you go for performance, go for c2d ;)
1.35v is a bug from cpu-z
real vcore was ~1.65v and it was just to test max htt :)
Ive got an lcbie 0619RPMW x2 3800+
it can only do 2.8GHz max on stock vcore....and more vcore doesn't even help it overclock more - maybe its my mobos htt limit though, an old nforce3.
i run it 24/7 folding @ 2700 due to high temperatures, need to buy a better heatsink/fan.
What about removing the IHS?
I'll look into removing the IHS, is it safe to do this though?
I've got a feeling the wall at 2.8GHz is my old mobo not liking over 280htt.
got it upto 3 gig stable on 1.55v but I have to lower my memory divider to 100MHz (133MHz Divider doesnt POST) so Im best off leaving it how it is as its actually slower at 3 gig with that divider than it is at 2800 with the 166 divider.
http://valid.x86-secret.com/show_oc?id=140583
http://valid.x86-secret.com/show_oc?id=117133
old but still working :) max 3.21ghz stabil :) not bad with hs on and bad tunet SS
That´s what i got so far, 2,6ghz@1,48V, also Primestable (primed for ~8h). Highest Boot into windows without overvolting was 2,9ghz@1,65V. But i´m still testing :D
4200+ X2 CCBWE 0532MPM cooled W/Thermalright XP-120
252Mhz * 10 = 2517Mhz ( not worse than a 2800Mhz X2 3800+ actually:rolleyes: )
System
ASUS A8R32-MVP Deluex 0602 BIOS
ATI X850XT PE 250MB
2x 1GB CORSAIR CMX102403500LL (252Mhz 3-3-2-7-1T)
WD Raptor 150GB 16MB
550 Antec TruePower PSU
OS-Win XP Pro SP2
VID= 1.400v (BIOS(
VID SPECIAL= ?
CHIPSET= Disable
LDT= ?
LDT= ??
CPC = Enabled
CAS Latency(CL) = 3.0
RAS to CAS(Trcd) = 3
Min RAS# Active time(Tras) = 7
Row Precharge Time(Trp) = 2
Row Cycle Time(Trc) = 11
Row Refresh Cycle Time(Trfc) = 13
Row to Row Delay(Trrd) = 2
Write Recovery Time(Twr) = 3
Write to Read Delay(Twtr) = 2
Read to Write Delay(Trwt) = 3
Refresh Period (Tref) = 0128 =200 3.9us
Write CAS Latency(Twcl) = 1
DRAM Bank Interleave = Enabled
Skew = Off
Skew Value = 0
DRAM Drive Strength = Auto
DRAM Data Drive Strength = Auto
DDRAM Response Time= Normal
Max Async Latency = 7ns
Read Preamble Time = 5.5ns
Idle Cycle Limit = 16 clks
Dynamic Counter = Enable
R/W Queue Bypass = 8x
Bypass Max = 4x
32 byte Granularity = Disable(4burst)
http://valid.x86-secret.com/show_oc?id=144228
All prime stables for 5 hrs b4 I stopped it
Pass Super PI 32M test
Couldnt do better than that.. the m/b offer the CPU voltage up to 1.400 -_-
http://img373.imageshack.us/img373/7...perpaj6.th.jpg
http://img90.imageshack.us/img90/206...perpms2.th.jpg
http://img120.imageshack.us/img120/2...perpch3.th.jpg
http://img382.imageshack.us/img382/6...2004yu4.th.jpg
This is my little X2 3800
http://www.bilder-hosting.de/tbnl/DN3OP.jpg
And thats what the Baby does make on Standardvcore of 1,35Vc in the Bios
http://www.bilder-hosting.de/tbnl/DN584.jpg
Bit confused about where the in place to post OC's is atm since their are quite a few in the discussion thread!
Anyway, thought I'd post my results since I prolly won't be running these clocks day to day.
AM2 5200+
http://img100.imageshack.us/img100/1...06cropsnw2.jpg
http://valid.x86-secret.com/show_oc.php?id=156186
I did some breif stability testing at 11 multiplier (form earlier testing)
http://img186.imageshack.us/img186/1...ed22lh1.th.jpg
Now I'm pretty happy with these clocks, but for pure experimental purposes I am NOT happy with the bug this CROSSHAIR mobo seems to possess.
Essentially 1.55v is the highest Vcore I can get out of it, Regardless of what I set it to in bios (can set upt o 1.85 iirc).
Very frustrating as I can do suicide runs at 3.25ghz if I get the water cold enough, and keep load temps under 50. but I'm confident I could actually get it to run much faster at 1.6 (not willing to go higher than that anyway, even on water) coupled with chilled water.
Not an issue day to day though, as Due to my sys being a comprimise between silence (passive watercooling) and performance, my day to day clocks are 3.06Ghz @ 1.45 set Vcore. Runs this extremely stable (havent 24hr orthos yet, but been running non stop for days and days, + playing games, etc).
http://valid.x86-secret.com/show_oc?id=156078
(suicide shot of course :cool: )
x2 3800+ Manchester (LDBHE 0604 WPAW)
DFI LP UT NF4 SLI DR Expert
1.7 vCore
Zalman 9500AM2
2x 512 MB Twinmos
it has one bad core that does 2.6 GHz prime stable (1.65 vCore) and the ohter goes up to 2.8 (too bad both cores have to have the same clock:dammit:)
I have an 3800+ X2 Socket 939, stepping available if you want it!
VCore=1.450V
HT=295 MHz
Multi=9X
CPU clock=2655
CoreTemp readings:
idle:
Core0=30C
Core1=35C
Load: (Orthos after 1minute)
Core0:45C
Core1: 60C
Probably could go higher but I need to get my RAM stable and to spec....having some issues and will probably have to RMA :\
x2 3800 lcbie 0628dpmw
picked this gem up from ebay a week ago :P
http://homepage.ntlworld.com/chris_f/woot.jpg
1.37 volts for 3 gig :) on basic watercooling
I have an 3600+ X2 Socket AM2 Windsor ( I didn't see any one OC that CPU)
http://valid.x86-secret.com/show_oc?id=157057
VCore=1.2750V
HT=240 MHz
Multi=10X
Vdimm=df
http://valid.x86-secret.com/show_oc?id=160373
VCore=1.2250V
HT=230 MHz
Multi=10X
Vdimm=df
I'm trying Super PI and pass 32M but when try Orthos option Blem test not pass 15m but test CPU only pass >5h. Are the memories false or Vcore is too low?
Hey Newb. Nice OC for that chip :)
I think you'll find your CPU-Z is reporting V-core wrong though. Mine does the same. Maybe it's Windsor compat thing. Try a mobo supplied app like PC probe for asus (example), OR dl Speedfan http://www.almico.com/speedfan.php , and check the VCORE 1 voltage (NOT vcore 2) , it reports correctly for me.
Cheers
New CPU: CCBBE 0615DPMW :)
http://img216.imageshack.us/img216/1801/fx623de.jpg