Tried 2.8GHz @ 1.52Vcore with Zalman7700CU..
3200+ Venice 0517BPEW
OCCT --> HERE
Printable View
Tried 2.8GHz @ 1.52Vcore with Zalman7700CU..
3200+ Venice 0517BPEW
OCCT --> HERE
How is it a bad CPU? It runs fine at stock speeds doesn't it? That's all it was intended to do.Quote:
Originally Posted by Xyus89
Where here at xtremesystems.org not atQuote:
Originally Posted by Dave_Sz
www.i-love-running-my-computer-stock.org :D
Here is mine. Still using stock AMD cooler. I am not sure if my memory is tweaked to the max or not. I know that I can't budge on the 2.5,3,3,8 timings and can't get 1T out of my ram but not sure if the other advanced timings could use some tweaking. I'm getting an XP-90 with panoflo and as5 coming to me, hopefully then I can squeeze a bit more out of it. It's 100% stable in all games/folding@home I throw at it. :D
http://img374.imageshack.us/img374/2...ice25507js.jpg
CPU: Athlon 64 3000+
Venice, Rev. DH-E3, LBBLE 0520BPMW, 1800@2700 1.65V (CPU-z uderscores)
CPU Cooler: Tt BigTyphoon
Max Idles: 35-36 *C
Max Loads: 54-55 *C (S&M v.1.7.2, High Priority, 100% Load)
Specs:
MB: DFI LP NF4 SLI-DR (Rev. AB0), BIOS Rev. 623-3
RAM: Kingston 2x512MB KHX PC3200 (Winbond BH-5) 2-2-2-5-1t 200@193 (CPU/14) 2.70v
Video: PCI S3 Trio64 V2/DX 1MB
HDD: IBM 60GB PATA-133 (IC35L060AVER07-0)
---
Comments:
Tested with Prime95 v.24.13 (Large FFT, High Priority).
2750 is unreachable. :stick: I'm not impressed with this Venice to say the least. :(
Hi,
I've got a venice +3000 but I can't see my rev with cpu-z 1.30.. ?
xyus
Try use CPU-Z ver. 1.29.
here
3200+ venice
http://valid.x86-secret.com/show_oc?id=34032
http://veytrex.net/1/cpu2.gif
Did someone test a 3200+ E6 already?
I have 3000+ LBBLE
DFI nf4 Ultra-;D
2*256MB NItro pc 3600 CL3
gf 6600gtextreme ledetek
Zalman 7700ALCU
BIOS 623-3!
I go to 2817Mhz at 1.776V SUPER PI 1MB stable! http://www.freeweb.siol.net/cpotocar/best2.JPG
Then 2745Mhz at 1.744V super pi 32MB stable! http://www.freeweb.siol.net/cpotocar...32mb-28min.JPG
Max BOOTEBLE freq: 2864Mhz vith 1.776V i don'g get higher with AIR Cooling!
My ram IS in F..K..G they don't go over 210 at CAS 3 at 3v???:mad:
Wow, 1.744v to get stable at 2.745Hz :eek:
Personally I would prefer a lower vcore on Venice than that...
just oc'ed my 0512 dpbw venice 3000+, to 2.8ghz (well 2799mhz to be exact) with 1.45v, - load temps after 10 hours of prime top out at 41degrees with an xp120 - but cheappy silicone goop until I lapthe heatsink properly at which time as5 will be used. Boosting voltage to1.475 doesnt seem to help to get 2.84 stable, is it worth trying more voltage to see if it can go higher, or would I see only small differences from here. Anyway my ram holds me back (currently on a divider running at 466 at 2.5-3-3-6 timings - but can manage up to about 490 on same timings - result of a mushkin blueline rma - went from utt to mosel chips) an 2.8 is a very nice result anyway, still any advice?
Quote:
Originally Posted by fxr91
yes i don't know why? mybe bios? i try with 8,5*330 and its stable at same voltage.
Mine will be here friday. I'm planning to burn it in for a week or so and I'll definitely post some screenies. Don't get your hopes up, this is my first RIG build/OC.Quote:
Originally Posted by d4n13l
Ok, I'm waiting...Quote:
Originally Posted by Dave_Sz
0523 EPMW 0794
http://users.telenet.be/jortcollijn/...ice/31.265.JPG
some testing my new cpu, its on water;)
1.6V but i'll work on it
Well, SVC and NEWEGG fudged up, mobo won't be here til monday, xp-90 on tuesday. The mobo, xp-90, and the venice were all bought within 30 minutes of eachother. Only the chip from ewiz will be ontime, friday, the mobo and HS were both rescheduled for no reason.Quote:
Originally Posted by d4n13l
Hi,
My new cpu. E6 0528 GPFW (that's why revision is empty)
http://img373.imageshack.us/img373/7943/superpi27am.jpg
good cpu , I'm sure I can hit 2800 mhz with 1.8vcore, it loves the vcore a little to much :(
Xyus
plz give commments.
Watch the volts Xyrus, thats very high for air, much higher than i run on water.
I know,
otherwise it isn't stable :(
xyus
but 1.8vcore for 30secondsd ain't gonna harm the cpu that much ;)
updated: here's my 0520APMW sPI 32m stable:)
http://img342.imageshack.us/img342/6...apmw32m9la.jpg
current settings:
http://img342.imageshack.us/img342/1...ettings9vm.jpg
http://img391.imageshack.us/img391/655/2931wg.jpg
on stock cooling
Hey guys i`ve got a quick question regarding my temps. I put 1,425x113% on my 3200+ @ 2780Mhz , mbm reads 1,55-1,57v it fluctuates :( . Temps on load are 40°-42° on cpu 60+° on pwmic and 42°-44° on chipset. So here comes the questions :) : Should i remove the heatspreader (i`m a little afraid of it cause i`ve never done it before) and second question what can i do do stop vcore flutuations ? I will put a fan near the pwmic to cool it better, 60+° seem a little high, but now tell me your answers ;)
Edit: forgot to mention mb is DFI Nf4 SLI-D
Here's my Venice 3000+ 0517DPMW at 2908MHz@1,5v bios, DFi NF4 Ultra-D and 2*512MB Twinmos Speed Premium PC3200 264MHz@3.4v 2-2-2-5-1T with stock cooler:
http://xtremesystems.org/forums/atta...id=36437&stc=1
Your temps are good. If you remove the ihs, I doubt you'll get more than 2-3 degrees better. That's about all I got. The vcore fluctuating a little is normal. As far as pwm temp, mine never gets above 50 -52, but I've seen others with temps in the sixties. Putting a fan over it should bring the temp down. If you do decide to take the ihs off, some acetone will help soften the sealant, and make it easier to cut.Quote:
Originally Posted by ic3m4n2005
My E6 0530CPFW does 2.52@1.45, 280x9. Anything higher and it fails prime within a minute. No screens sorry, my mobo suffered a crash during a bios flash.
I have to work on my memory timings and get them a bit tighter but its doing OK so far at 10 X 290 t1 one to one. 3d stable.
hy guys! ;)
I've not got idea of how to get an stable and decent overclock with my A8N-SLI premium mobo, my Venice 3500+ core and my pair of Dimms--> 2x1024 OCZ PC 4000: 3-4-4-8 (PSU Enermax 480W kill noise, tower Kandalf by thermaltake, VGA: ASUS EN7800 GTX)
Now I'm running my system at @2651 (2200 default) with this config in bios:
Multi: 11x (Default 11x)
Vcore:1.550 V
Clock: 241 MHZ
DDR CLOCK: 400 MHZ at 3(Tcl)- 4(Trcd)- 4(Trp)- 8(Tras)- 11(Trc)- 16(Trfc)-5 (Trwt)- 3(Twr) 1T------> I don't Know if the Trc,Trfc an the Trwt values are correct because the bios autoset it to 400 MHZ with 2T and i set then to 1 T. What do you think about this? Should i change it?
DDR Volt. 2.80
Chipset Volt: 1.6
HT volt: 1.5
HT multiplier: x4
amd cool n quiet : Off
--------------------------------------->all is stable with superpi and mentest at @2680 and prime fails, but with this configuration prime95 is stable during 5 hours more or less (memtest and superpi o.k.) then crash :banana: .
my results in sandra are :
CPU: between Athlon 53 FX and Atlhon 55 FX-->11100/5425
Memory band...:6750/6650
my temps with my zalman 7000-B CU are:
Idle:43º
Full: 55º
Chipset: 126º fanless
I'm very confused about how i must to do the correct overclock.
What do you think about this config?
At this moment is the most stable config. in performance/stability but I think that is a poor overclock. :(
On the other Hand, clockgen say to me that my system is stable over 2690 but then prime95 fails.
Please post all your opinions and sugestions over this config and others that you think that could be better than this one and what i must to do or not to do...
Please help!!!
Thanks in advance and sorry for my poor and terrible english...Rob :slapass:
today i have received an 0531 BPMW
it does 2 ghz on stock voltage for now, but the psu is freaking out, i think thats the main problem, at 1.4V and 2.050 ghz it just freezed, raising up the voltage did nothing
at 2 ghz its stable but even at 2.025 its not
weird imho
just waiting for my new psu and i will give you some screens
how do you see its an E6 ???
Look IHS, it if ends in BW then it's an E6.
Through CPU-Z it should have stepping 2 (F F 2)
well im confused, my MB rates to above a 300HTT but i cant get it past 270 my mem is stable at 2.5-3-3-7 past 230 and the 3000+ is supposed to at least get 2.4, i cant get past 2.2, now the odd thing is that i cant max out everything at one time, BTW im relativly new to this OC thing, and at the settings below i have flashing on the screen, (it will flash black and than go back to normal. i can superpi it just fine so its stable, im confused. HELP!
http://www.xtremesystems.org/forums/...id=36859&stc=1
http://img148.imageshack.us/my.php?i...32stable3l.jpg
not tested further because i have strange issues
stepping 0531 BPMW
Great post, Friday afternoon, after work. Could end up in someones sig. If you need any help plenty of people here.Quote:
Originally Posted by GoThr3k
you mean, that someone could use my screen, tis a sucky screen i have some better right now
will use something on it, thx m8
it does 2.75 @ 1.5V stock cooling, NO airflow
No, not really what I meant but that is ok. 2.75@1.5v is good, but your right.. try to get a better fan/hs.
ah, you ment up that voltage and see what you got there
i know, normally i will put phase change on top of that middel october orso
0520DPAW.. n1 Stepping! :toast:
http://img355.imageshack.us/img355/5694/268s5et.jpg
DAMN 1.744 V, YOU GOT SOME BIG ASS BALLS!!!!!!!
AND CPU-Z UsuAlly TELLS YOU LESS THAN THE CORRECT VCORE ON DFI BOARDS......
BADASs
1.744 isn't that extreme for watercooling. Now, 1.8 would be. Anyway, nice clocks Gravedigga, that's very impressive for normal watercooling!
:p: :eek: I,m using 1.86V at my MSI Neo2 (venice) at boxed air cooling.Quote:
Originally Posted by Rezag1000
^Ok I guess you're already looking for a new a64?
UPDATEQuote:
Originally Posted by Dave_Sz
I also received a E6 3200 and this one is also stuck at 2500mhz. Both my e6 procs are stuck at ~2500.
What's your mobo Dave_Sz ?
Is that bragging or exclaiming that the Neo2 is undervolting? If the volts are that high, i would like you see you prime it all day...Quote:
Originally Posted by Hugo van Dijk
:explode2:
9npa ultra. I also just did some testing on the DIMM slots. Slot 2 and 4 max out at ~280 while slots 1 and 3 max out at 303. What a :banana::banana::banana::banana::banana:, ey?Quote:
Originally Posted by ReelMonza
heres my newest, man these vennnys fly on stock voltage well a little above on this one... just a lil so i could pi it :toast: , just wish i had some faster mem... oh the perils of a college students wallet
http://www.xtremesystems.org/forums/...id=37050&stc=1
yeah man i got simular results with my 3200 venice. heres a shot of 2800mhz 1:1 1.4v and climbing...
peace perc,
-22C? not really similar :p:
Great CPUs anyway
Mine was going about 2850Mhz @~1.4V on boxed heatsink, not 1:1 tho. After this, it needs about +.25V to get to 3Ghz. Raising voltage past this point is just calling for instability, even if the temp are fine; <40C :confused:
Quote:
Originally Posted by JfRsQ
LOL its a stock mach1 i think mb5 is off just a few degrees! i always chuckle when i see that -22 on my desktop :D cause i know that unit isnt getting -22c at the core.
so your saying that with that venice you cant give it more then 1.425v or am i missreading? i would think that these venices would handle 1.55v-1.65v depending on you cooling no? plus 3gigs at 1.425v thats a nice chip! id like to see your chip on phasechange i bet it would fly. im aiming for 3200mhz out of this 0521DPMW veince i have. but knowing my luck ill be in the same 2800-3000mhz range i cant seem to bust out of? think i need colder unit that would help! ok man good luck...
peace perc,
No,
1.40V
+0.25V
______
1.65V
No matter what voltage higher after this, it's windows instant freeze, or BSOD :stick:
dammit man thats not cool at all. that chip would need a good phase unit to stay under that voltage... this one i got aint to bad at all im at 3000mhz using 1.5v in the bios but windows it only reads 1.456v.
peace perc,
Very nice chip perc. I know once you give it some real volts it will be way past 3 Ghz.
I always use CPUZ for the V readings so that looks like 3 Ghz with 1.45 volts.
Anyone had any experience with an E6 3500 Venice?
I want to know if there's something I'm overlooking on the configuration side or if some hardware component is holding me back. I'm pretty sure my ram is holding me back but I want to make sure before I make my next purchase.
So far I've reached the best stability and performace with my settings as follows:
HTT:240
Hammer Multi: 11x
Mhz: 2640ghz
HT=3x 16x16
Ram Timings=1:1 3-3-3-8 1t
Vcore: 1.65v
VDimm: 2.8v
Chipset: 1.6
A64 Venice 3500+ E6 LBBWE 0528APAW (Naked Core)
Zalman cnps7000-cb
BFG Nforce4 Ultra Mobo
Samsung TCCC 2x512 Dual-Channel Rated at 3-3-3-8 1t
Enermax 550w PSU 5v-36a 12v-36a
ATI Radeon x800xl PCI-E 256m cooled by a Zalman vf700-cu
SBLive 24bit PCI
WD 250gb SATA
Quote:
Originally Posted by Absolute_0
why thank you :) heres a shot of 310htt 1:1 non suicide shot this is very benchable!!
peace perc,
Hey perc nice oc and very nice chip! :woot: What temps are you getting? Are they much lower than the X2?Quote:
Originally Posted by Perc
hey thx man i bought it off this kid who didnt know what he had :slap: ! hey this is my latest super pi 1m run. have a peek i think its decent. ive never realy had good super pi times before...
peace perc,
New one.. 0520EPMW with IHS. It rocks! :toast:
http://img375.imageshack.us/img375/3...139vihs7cu.jpg
http://img218.imageshack.us/img218/5...z139v2m3xs.jpg
http://img314.imageshack.us/img314/1...9vprime6mv.jpg
http://img139.imageshack.us/img139/3...hz15v2m7mv.jpg
http://img355.imageshack.us/img355/5...emitihs4nt.jpg
http://img26.imageshack.us/img26/626...z2m155v4fj.jpg
http://img370.imageshack.us/img370/7...6vprime4ie.jpg
Extremely nice CPU... now let's see 10 hours of SP2004. Looks like it will run 3 Ghz pretty easily with a little more volts. I am prime stable at 3 Ghz but it requires 1.73 volts, load temp @ 39-40C. With that many volts that CPU would probably be around 3050! :drool:
Ur CPU is without IHS?
I've pluged in this CPU 2h ago, had no time to run longer Prime95, just testing what i can expect. :toast:
Yep IHS removed
I forgot your IHS is still on - that is a very sweet CPU! Dont forget to do burn in.
Yeah, maybe i should try an Burn-In, but my PC is 20" away from my bed, so i can't sleep.. we will see ;)
Grave :
you got yourself another one? What happened with the first one? Week 20, if I remember correctly.
Yes, the other one is already by his new owner. ;)
Got this CPU today with mail from ebay.
Very nice results.
You're very lucky finding a good performing week 20. :toast:
Thx, but the finder is a friend of me! ;)
Anyway, i have fun to test this great CPUs! :toast:
[Off-Topic]
Do u have permission to change titles? :)[/Off-Topic]
3200+ Venice E6 LBBWE 0531 EPEW maxing at 2.5Ghz 1.6v :slobber: but first time i can bench SPi 32M stable my TCCD over 300mhz 2.5-3-3-7 1T -good IMC indeed
http://img50.imageshack.us/img50/51/306trcd35cy.th.jpg
yeah im lovin my 3200 venice. these chips are deff nice im at 3100mhz now using 1.55v in the bios and cpu-z is showing 1.504v wich isnt bad. one thing im starting to notice is that anything over 1.6v the cpu will eror out in super pi where as with less volts it doesnt :shrug: im thinking that if you cant get your oc using less then 1.6v then your screwed! atleast with the cpu i have anyways....
peace perc,
Final results, no time for longer testing. :
http://img297.imageshack.us/img297/2...withihs4eq.jpg
:toast:Quote:
Originally Posted by GravediggA
That,s a sweet CPU :slobber: :slobber:
:clap:
Very nice, looks like my CPU but needs .1 volts less! That is sweet stuff
Here is my CPU on the DFI NF3, this is back when it still had the IHS
http://img.photobucket.com/albums/v7...clocking/2.jpg
:slapass:I'm getting similar results with my 3200+. 1.7V is instant freeze as soon as I'm clicking an icon on my desktop :slapass:Quote:
Originally Posted by Perc
look at this cpu :drool: njkid is getting some damm sweat cpu's!
http://img182.imageshack.us/img182/5...51259327ed.png
peace perc,.
lol perc, he just showed me that pic, i was so amazed! Now he just needs to bump the voltage up...
its 0521DPMW 0098 btw.
Cooling*? IHS? ;)
* Got it.. Mach 1
Well I just picked this thing up and popped it in. I didnt even run it at stock. I just wish my ram would do 330. LOL to bad I prolly am going to sell it.
cpu-z verify----
http://valid.x86-secret.com/show_oc.php?id=39888
http://img264.imageshack.us/img264/9...08002iq.th.jpg
your not selling that cpu and if you do its going to me :) no way am i letting that slip away to anyone else.... these 0521DPWM steppings i hardly see on these forums and the ones i do see are ocing like mad! shame you cant run that thing at 1:1 past 310htt i gues a divider doesnt hurt that much just a shame thats all. nice chip man make sure you let me know if you sell it...
peace perc,
I don't have Windows running to get a CPUz shot, but this survived a full day of FreeBSD's `make world`, which is a very hard test (recompiling the whole system with itself, and any memory error leads to compilation failure).
My E6 3200+ does 2500 at 1.525 volts (ram under 200 MHz) with a Zalman CF-7700-CU at full RPMs.
2600 MHz did not run even at 1.50, so I'm testing 2550 now.
The DFI LP Nf4's temperature readings don't work in FreeBSD so I have no idea.
Hello!! What Can you tell me about this Stepping ? 3800+ Venice
ada3800aa4BP
lbble 0524 EPMW
z707522f50961
Thanks!!!
Venice 3000+
ADA3000DAA4BP
YBBLE 0523CPGW
Q337396F53002
8*337@1.65v
cpu-z ID 30607
All that runs on crap Gigabyte 100$> board K8NS-939 with nf3 ultra chipset
so i thinks its the boards limit
cooling= very custom home made gas cooling, temps about 5-10 degree Celsius
didnt manage to take any pics except of cpu-z verification because cooling began to leak, waiting dor dfi nf4 sli-d to arrive to maxx out and some gskill pc4400 is on the way too
All on air, thermal take big Typhoon cooler..
http://www.3dxtreme.net/other/CPUS/3...W/IMG_1960.jpg
Low volts - prime, occt and super Pi stable.
http://www.3dxtreme.net/other/CPUS/3...38.53%20PM.jpg
High volts - OCCT and Super PI32M stable, not prime stable though.
http://www.3dxtreme.net/other/CPUS/3...5SPMW/2915.jpg
Well here is the newest chip I got today just a couple of hours ago. Its another 0521DPMW batch is 0070 nice and low just like I like it! But here is just my initial testing but there will be more to come.
http://img316.imageshack.us/img316/9...08578xr.th.png
http://img99.imageshack.us/img99/588...57269mg.th.png
And the highest so far at 1.5v
http://valid.x86-secret.com/show_oc.php?id=41864
http://valid.x86-secret.com/show_oc.php?id=41932
WOW!
I don't believe these results
I now can hardly get my CPU stable at 2750.
Not sure what is causing my problem.
Nice results! :toast:Quote:
Originally Posted by njkid32
Sure u doesn't mean DPMW instead of DPWM? :)
Oh yeah LOL your right typo!Quote:
Originally Posted by GravediggA
holly crap dude ! nice OC, congrates ;)Quote:
Originally Posted by njkid32
Today i got an second 0520DPAW, dropped it in and first boot with this settings.. Prime runs fine! :D
Really great stepping it is! :toast:
http://img331.imageshack.us/img331/2954/30000kv.jpg
Does exaktly the same as my first 0520DPAW. I think i can expect 3100MHz SuperPI 1M too. :toast:
http://img231.imageshack.us/img231/4...ihs157v1yb.jpg
What do you think of thes OC?
http://valid.x86-secret.com/cache/42470.png
Here the validation:
http://valid.x86-secret.com/show_oc?id=42470
Very nice!
What cooling r u using? What Steeping is that?
http://valid.x86-secret.com/cache/42561.png
Validation: http://valid.x86-secret.com/show_oc?id=42561
I use the boxed cooler but have a nice ventilation in the cabinet ;) (35° full load)
What's up with some SuperPi;Prime95 or other benches? SS are a bit boring.. and Vcore? :rolleyes: ;)
Well here is another addition to my collection of chips. LOL (sorry not bragging!) This one is one of 2 0517BPDW's that I just picked up. I dont think they are as good as the 0521DPMW's that I have. This week 17 doesnt scale the same way. It needs alot more voltage to hit the same speeds as the week 21 chips. But this is still a pretty good clocker. Here are some tests right out of the box. Maybe the voltage will improve with some burnin or just day to day use.
http://img80.imageshack.us/img80/3831/32ghz13qp.th.jpg
http://img80.imageshack.us/img80/8054/32ghz21pl.th.jpg
Ok I finally got around to testing the other 0521DPMW and it seems to be doing pretty well. Its the one on the left side of the pic.
http://img438.imageshack.us/img438/4...ips24in.th.jpg
http://img294.imageshack.us/img294/9796/32ghz5cm.th.jpg
http://img421.imageshack.us/img421/3...uz336ne.th.jpg
http://valid.x86-secret.com/show_oc?id=42902
Edit--just messing with this chip a little more and here is a cpu-z shot of 3.6ghz.
http://valid.x86-secret.com/show_oc?id=42910
dang, got an E6. Not cool... well, I won't be OC it, I'll see how much I can undervolt it at stock clock. (The CPU is for a CnQ-HTPC)
Jesus, you won't OC it cuz it's a E6? WTF? I have 2 E6 at 2.6ghz+ with 1.5v or so.
http://web-upload.com/uploads/ebay.jpg
Dont know if my power supply (350W, installed a 7800GTX) is too weak for more MHzs.
LBBLE 0521CPMW :-(
Anybody know where I can buy a decent Venice anymore? I've been browsing for sale forums, etc...but it's nearly impossible to find a good week or a proven OC'er.
I bought one venice 3000+ and his step is:
ADA3000DAA4BW
LBBWE 0521DPBW
Z510316F50831
I want to know as I can give with him. my mems is Patriot XBLK TCCD (which the best times for them?)
Sorry for my english...
thks :D:D
Quote:
Originally Posted by PEARLboy
Same week, so its possible that ya CPU will go like mine...
I have a 0521DPMW 3200 that does really well. So it looks like the 0521's are the way to go now for the Venice.