I REALLY fail to see what can be gained from flashing to an inferior bios?! The Rampage bios may be slightly tougher on ram and chipset timings but once you learn the ins and outs of the bios, it's day and night in comparison to the lacking Maximus bios.
i try to flash rampage bios on maximus,but not work.please advice me
thx
How did it "not work"? Did you follow the guide in the first post?
Well i was able to play games and boot into windows fine with the latest maximus bios (goal is to reach my rams at 1200mhz), but any kind of stress testing failed.
So now i've flashed back to rampage bios 0501 and its just as unstable as ever.
I dont know why this viper fin 9600 micron d9s hate this board so much. im going to try the rampage bios 0403.
Post your full bios bios settings.Quote:
Originally Posted by slugzkea
soon, back on the maximus bios gonna try a few more things..Quote:
Originally Posted by Zucker2k
but honestly, 1164 or maybe even 1181mhz is the highest i can achieve. ive tried advanced skew 300, 100, 50, ive tried pretty much everything but i'll post the bios settings soon.
Are there chips on both sides of the memory sticks? Check this post for a way to verify if the Patriots are really D9s. You shouldn't be having anywhere near this much trouble.Quote:
Originally Posted by slugzkea
After talking to patriot themselves they claim the black viper fin 9600 are D9's. 1200mhz still is a no- go, though.Quote:
Originally Posted by Shiranui Gen-An
Here are my bios settings to attempt 1200mhz on maximus bios 1207:
Extreme Tweaker
Ai Overclock Tuner : Manual
OC From CPU Level Up : AUTO
CPU Ratio Control : Manual
- Ratio CMOS Setting : 9
FSB Frequency : 450
FSB Strap to North Bridge : 400
PCI-E Frequency: 110
DRAM Frequency: DDR2-1199
DRAM Command Rate : 2T
DRAM Timing Control: Manual
CAS# Latency : 5
RAS# to CAS# Delay : 5
RAS# Precharge : 5
RAS# ActivateTime : 15
RAS# to RAS# Delay : 3
Row Refresh Cycle Time : 45
Write Recovery Time : 6
Read to Precharge Time : 3
Read to Write Delay (S/D) : 8
Write to Read Delay (S) : 3
Write to Read Delay (D) : 5
Read to Read Delay (S) : 4
Read to Read Delay (D) : 6
Write to Write Delay (S) : 4
Write to Write Delay (D) : 6
DRAM Static Read Control: Disabled
Ai Clock Twister : light
Transaction Booster : Disabled
Relax level: 0
CPU Voltage : 1.55v
CPU PLL Voltage : 1.62v
North Bridge Voltage : 1.59v
DRAM Voltage : 2.28v (rated 2.3v, overvolt real = 2.3v)
FSB Termination Voltage : 1.52v
South Bridge Voltage : 1.050
Loadline Calibration : Enabled
CPU GTL Reference : 0.63X
North Bridge GTL Reference : 0.67X
DDR2 Channel A REF Voltage : AUTO
DDR2 Channel B REF Voltage : AUTO
DDR2 Controller REF Voltage : DDR2-REFF
SB 1.5V Voltage : 1.5
I've als tried 5-5-5-12 (rated), 5-5-5-18, 5-5-5-14, 5-5-5-16.
Farthest I can get is a stable boot, play games.
No Super PI, no PRIME :(
Dude, if that's your E8400 you're clocking, the FSB Termination voltage is WAY too high! You're gonna kill that thing!
it's been that high for as long as i can remember.
Yeah, that vtt myth has been long busted.Quote:
Originally Posted by slugzkea
Here are a few things I suggest.
1. I think you want to stay on the 400 strap so you can bring your chip/ram near their max ocs, but I'd rather get on the 333 strap.
2. change try 5-5-5-15-3-55 or 5-5-5-18-3-55
3. go up one count on TRD (PL)
4. Try a little more NBV
tried all your suggestions. any stress testing still fails within seconds.Quote:
Originally Posted by Zucker2k
Well guys, I think I got it. Been prim95'ing for a few hours now. I know that doesn't mean anything, but before, it would crash under a minute. So it's a good sign. I'll leave it prim95'ing over night but for now, time for sum games!
TACTIC: These rams were tested with P35 chippy's, so I used my Neo2-FR's Motherboard SPD timings on the Rampage.
Here are my current BIOS settings using Maximus Bios 1207:
Extreme Tweaker
Ai Overclock Tuner : Manual
OC From CPU Level Up : AUTO
CPU Ratio Control : Manual
- Ratio CMOS Setting : 9
FSB Frequency : 450
FSB Strap to North Bridge : 400
PCI-E Frequency: 110
DRAM Frequency: DDR2-1199
DRAM Command Rate : 2T
DRAM Timing Control: Manual
CAS# Latency : 5
RAS# to CAS# Delay : 5
RAS# Precharge : 5
RAS# ActivateTime : 15
RAS# to RAS# Delay : 12
Row Refresh Cycle Time : 45
Write Recovery Time : 12
Read to Precharge Time : 12
Read to Write Delay (S/D) : 12
Write to Read Delay (S) : 12
Write to Read Delay (D) : 12
Read to Read Delay (S) : 12
Read to Read Delay (D) : 12
Write to Write Delay (S) : 12
Write to Write Delay (D) : 12
DRAM Static Read Control: Disabled
Ai Clock Twister : light
Transaction Booster : Disabled
Relax level: 0
CPU Voltage : 1.55v
CPU PLL Voltage : 1.62v
North Bridge Voltage : 1.61v
DRAM Voltage : 2.28v (rated 2.3v, overvolt real = 2.3v)
FSB Termination Voltage : 1.52v
South Bridge Voltage : 1.050
Loadline Calibration : Enabled
CPU GTL Reference : 0.63X
North Bridge GTL Reference : 0.67X
DDR2 Channel A REF Voltage : AUTO
DDR2 Channel B REF Voltage : AUTO
DDR2 Controller REF Voltage : DDR2-REFF
SB 1.5V Voltage : 1.5
-----------------------------------
However, the results are terrible!!!
Your read/writes should improve when you enable PL/Transaction Booster. Enable transaction booster and note the PL level. Slowly decrease the value each time until it becomes unbootable. Then use the previous value which allowed post, should give you much better results.:up:
EDIT
Read about tRD and how it can help performance. It's an excellent read and can avoid the "guesswork" above.
i enabled transaction booster and the lowest level i could achieve was 7.Quote:
Originally Posted by chawks2
The results were nsaty. latency of 106ms, and lower read/write speeds.
slug, not sure where your problem lies. Maybe it's the ddr2-1200 stix?
Check the thread here, I posted my results with PL 13 vs PL 8 and there was a tremendous difference in memory speeds.:shrug:
Quick test of my board with the newly lapped cpu etc - all is well- still alive :)
~Bex
Cool, post up some pictures of your rig when it's done; your hardware's got me all interested in your posts all of a sudden :p:Quote:
Originally Posted by RCG_Bex
wanted to see if anyone could suggest some advanced timing settings for my ASUS Maximus Formula with the new Ballistix 6400 2.0V. I want like to see 1066 out of them. Thanks
CAS# Latency : 5
RAS# to CAS# Delay : 5
RAS# Precharge : 5
RAS# ActivateTime : 15
RAS# to RAS# Delay : ?
Row Refresh Cycle Time : ?
Write Recovery Time : ?
Read to Precharge Time : ?
Read to Write Delay (S/D) : ?
Write to Read Delay (S) : ?
Write to Read Delay (D) : ?
Read to Read Delay (S) : ?
Read to Read Delay (D) : ?
Write to Write Delay (S) : ?
Write to Write Delay (D) : ?
Write to PRE Delay : ?
Read to PRE Delay : ?
PRE to PRE Delay : ?
ALL PRE to ACT Delay : ?
ALL PRE to REF Delay : ?
DRAM Static Read Control: Disabled ??
Ai Clock Twister : Moderate ??
Transaction Booster : Manual ??
Common Performance Level ??
Pull-In of CHA PH1 Disabled ?
Pull-In of CHA PH2 Disabled ?
Pull-In of CHB PH1 Disabled ?
Pull-In of CHB PH2 Disabled ?
This will get my Mushkin XP2's to 1200MHz
You take a small read hit
CAS# Latency : 5
RAS# to CAS# Delay : 5
RAS# Precharge : 5
RAS# ActivateTime : 18
RAS# to RAS# Delay : 5
Row Refresh Cycle Time : 65
Write Recovery Time : 6
Read to Precharge Time : 5
Read to Write Delay (S/D) : 10
Write to Read Delay (S) : 4
Write to Read Delay (D) : 5
Read to Read Delay (S) : 6
Read to Read Delay (D) : 6
Write to Write Delay (S) : 5
Write to Write Delay (D) : 6
Write to PRE Delay : 16
Read to PRE Delay : 6
PRE to PRE Delay : 1
ALL PRE to ACT Delay : 6
ALL PRE to REF Delay : 6
I thought you had your RMA all sorted out?Quote:
Originally Posted by RCG_Bex
I had to RMA my Maximus the second experience was much smoother than the 3870X2 run
Well the GPU got lost coming from Taiwan and the repair centre sent the wrong card to the UK centre and they didn't tell anyone back at the repair centre so I was left 3 weeks with no clue as to what was wrong. Phoned Asus down south and they rumaged and found this out. now I have to wait another 3 weeks for another new card to come from Taiwan to replace the 1 lost etc.
The test was because Zucker got me worried incase I did let it touch - that n I was petrified I'd lapped my CPU to death! I was my first time :P
~Bex
I recall my first CPU lap, it was rather stressfull pushing the power button :DQuote:
Originally Posted by RCG_Bex
I couldn't do it - I got my BF to push the button so I could blame him if I broke it :PQuote:
Originally Posted by Grnfinger
~Bex
I'm sure that was the toughest thing he ever did.Quote:
Originally Posted by RCG_Bex
I just want to get your guys opinions on my overclock here. First off let me say im a total noob to overclocking, ive been reading about it but never actually doing it before im not sure if what im doing is ok or not. I got pics from my bios so you can see what I exactly did. I got a x48chipset rampage formula, q9550 quad. After this I did use occt to run a stabilty test and it passed. I am using core temp and just on desktop its sitting at 42c. During the test it was mostly at 62c. I have played cod4 for over an hour and cod5 for an hour as well and no problems.
http://i69.photobucket.com/albums/i7...i/SSPX0083.jpg
http://i69.photobucket.com/albums/i7...i/SSPX0084.jpg
http://i69.photobucket.com/albums/i7...i/SSPX0085.jpg
http://i69.photobucket.com/albums/i7...i/SSPX0086.jpg
http://i69.photobucket.com/albums/i7...i/SSPX0087.jpg