Printable View
I just finished some loops of 3DM06 and Cinebench R10 at 4600 without issue so its on to some 32m Pi for desert, should do 5G benchable once training is completed. My new Teamgroup 1300 got delayed about a week or more but I got some nice Ballistix and Gskill to play with for now.
It looks like this chip maxes out at just under 5G on water and runs rather warm compared to my 820A324 with the same juice. This chip also hates any voltage beyond about 1.6v even on this torture rack which is a little strange for having a 1.26vid though the stepping is just average joe and runs hot.:)
Hello guys, I got a strange problem with my E8600 /VID 1.25/ on RE mobo
- at frequency of 4 ghz /500x8/ it runs perfectly at 1.25 vcore and with every other voltages set to min /vtt 1.1, nb 1.25, sb 1.5, pll 1.5/ + all gtl refs set to -40
- at frequency of 4.25 ghz /500x8.5/ it runs perfectly at 1.35 vcore and with other voltgages set also to min
The problem is, that I canīt run it stable at frequency 4,5 + ghz. When i try to load at 500x9 or 450x10 at 1.45 vcore or more, I can run small ffts without any problem for hours and hours... strange thing is that I cant even run large ffts - everytime I run it I got the freeze of the system in max of 30 secs. I tried to tune every single voltage, refs, skews a so no, but with no luck, even more vcore didn't help. I also run memtest whith no problems.
Any suggestions guys?
Try gaming and some 3D Marks...Quote:
Originally Posted by Majkl
Quote:
Originally Posted by Majkl
You need more volts on the North Bridge.
I would agree on more NB vcore like 1.4-1.5v and perhaps increase PLL to 1.7. Your SB vcore should be lower like 1.25.:)
I have 2 screens to show from My E8600 on a P5Q Deluxe.
Attachment 92802
Attachment 92803
For this results i didn't use High Voltages on FSB Termination Voltage an PLL Voltage.
It is very interesting see you pushing Your CPU's at High Frequencies using a lot of FSB Termination Voltage an PLL Voltage.
As i know too much FSBTer. Volts and too much PLL Volts are 1st dangerous for CPU and 2nd for Motherboard.
The Voltages i use in 1st Screen are:
FSBTer.V 1.20V
NBV 1.20V
PLLV 1.52V
In Second Screen:
FSBTer.V 1.26V
NBV 1.26V
PLLV 1.56V
The Maximum Temps i reached was 54C°.
My question is Why are you Pushing so Much Volts on FSBTer and PLL ?
For me running that speed of 2520mhz would certainly not require high fsb or Pll vcore but long term use of high settings can and will take its toll on chips. Im testing this new chip right at around 4.8-5G when benchin and more juice is needed, my cooling setup never lets temps go above mid 50s even at 5G ever. This new 823A221 is by far the hottest chip I have seen in a while and I am currently testing it at 577x8.5=4904mhz at 1.58v.:)
With the right cooling system a lot of things more are possible.
At the moment i enjoy more Clocking using Air Cooling and the limits are quiet different.
Maybe in a next future i will go on Water.
Without a doubt major cooling is going to help obtain much higher stable clocks and that is what I am into. My Torture rack is just one of three custom built liquid systems I have running right now in this room and contains separate water loops for the chip/card plus has ducted cool air intake for the rads and case which is a modded CM stacker. In the winter I use ducted fresh air from outside when possible and during the summer I have other types of refrigeration which work good also. Here is 32meg Pi I just ran about 20mins ago to test the high fsb on this P5K, nothing special just testing the water. :)
Ordered from Newegg on Friday.
Q823A221
Just starting off. Wow!
My e8400 needed 1.55v for 4Ghz. I can't wait to see what this thing does. I can't believe I paid $269 for a chip that I didn't need. My e8400 was weak, but it was still plenty of power at 3.9Ghz. Hopefully, I get over $100 for my e8400 on ebay.
http://i280.photobucket.com/albums/k...brown/4gig.jpg
Some other guy with your batch hit 4.5ghz @ 1.4v prime stable 2hrs.
well doods,
im 4.5ghz 1.4v prime stable so im happy with that.
looks like the P5Q-E willgo on the bay!!:D
Pushing a little further. I think I'm gonna let it sit here for a little bit. With my e8400, I pushed it really hard right off the bat and it degraded initially. I'm gonna let this baby burn in a little before moving on . . . well, probably not. I'm not a very patient person. Should I not worry about PLL voltage, FSB termination and GTL ref until I get into higher clocks? Is it really just as easy as increase FSB . . . increase vcore . . . if vcore doesn't help, increase FSB volt . . . repeat? It looks like I have a stuck sensor too. It will probably start moving as I put some more vcore into her.
http://i280.photobucket.com/albums/k...rown/42Ghz.jpg
I am so glad I bought this chip. Sold my e8400 for $117 also :up:. I can't believe how much some people are being USED proccessors for on ebay. There's E6700 going for over $100!
I'm not sure wether to push for 5GHz or not. If I push now, I think I'll have a better shot than if I wait. This chips seem to degrade a bit initially.
http://i280.photobucket.com/albums/k...rown/45Ghz.jpg
Quick prime95 small fft's test with my new E8600 Q820A597. I'll leave it for an hour more or so and then I will try 450x10. :D
Vcore might go lower one notch or two, not sure yet.
http://img528.imageshack.us/img528/663/19903602pv9.png
http://img528.imageshack.us/img528/1...ng/1/w1373.png
How are you people getting past 4.2ghz
I've tried everything, and it still fails Ortho
what am I missing
Bios: 1702
Multi - x10
Strap - 420
CPU Front Side Bus - 333
CPU V - 1.3625v
DRam - 2.00v
CPU PLL - auto
North Bridge - auto
Front Side Bus Termination - auto
CPU GTL - auto
North Bridge GTL - auto
CPU Clock Skew - auto
North Bridge Clock Skew - auto
cpu - load on
BAtch # Q820A306
Need someone's help
Thanks
These settings seem very bad to me :xQuote:
Originally Posted by Nobby_74
Check here pages 206 and up should provide you some info.
AUTO KILLS !!! Try the changes above plzQuote:
Originally Posted by Nobby_74
have E8600 batch Q820A747 Asus P5Q DELUXE bios 1702
Manual
Cpu ratio setting 10.0 Fsb frequency 399 Pci and frequency 100 Fsb strap car Dram frequency ddr2 1063mhz Cpu voltj 1.24375 (bios) Cpu gtl 0,630 Cpu gtl 0,630 Cpu pll 1.60 Fsb terminator car Dram volt 2.1volt Nb volt 1.40 Cpu clock skew delay 100ps Nb clok skew delay 200ps Cpu margin enchancement optimized
24/7 that I can raise or to go down to improve my oc =?
Ventilador Big Tyfon
Hye folks ! Just seen this thread for the first time :D
That's what I've done long time ago now, but changin' the mobo soon for an EP45T UD3P, so guess it would be better than the MIIF xD
http://images4.hiboox.com/images/080...4bcac9fc34.jpg
I was looking for the highest ram frequency : and that's what I reached :/ (for the mobo of course, my crucials are better than this)
http://images1.hiboox.com/images/080...23735db879.jpg
My 24/7 or my lanparty rig if you want (have a look at my signature)
http://images2.hiboox.com/images/080...8ce6ecc6e5.jpg
Just for fun : this is at all what I love !! ^^ 4870+4850 : CrossX Powaaa !! (30k 05 & 21k 06 \o/)
Next stage : CrossX of my two 4870 (1gb & 512mb) ...gat to cool this rig down after all : cus' so hot in my country :D
I've been running stable at 4.55Ghz 1.44v since September, still rock solid!
--Matt
Prostitute that they are paletiados in to answer my questions, demas of doing it villains throw oc terribly xD
Got cpu week 22, is this batch meant to be good one ??
Hi all,
I have a problem with my CPU, I use CoreTemp and RealTemp to monitor the CPU temperature and in idle it shows 39š and 40š degrees and when I oc the CPU up to 4000ghz it shows also 39 and 40, I dont think that is normal, can some one please help?
Regards