Apogee GTZ

Printable View

Show 100 post(s) from this thread on one page

08-13-2008, 03:49 PM
Martinm210

Quote:

Originally Posted by mcoffey

LOL...yeah, you have to keep it fresh and fun. Thank God I don't have to drain my loop or wait for it to bleed anymore. I couldn't take much more of that.
Meet the triplets. Moe, Larry and Curley. Shimps on the bench:D
andyc

Yeah, I did something similar, but just some Zurn 3/4" hosebarb brass globe valves. If you look down the opening of these guys when open, there is no restriction at all. Then all I have to do is blip a few bubbles into the reservoir and I'm off and running again.

This also allows me to pull the entire loop away from the case when switching out blocks. Me and spilling go hand in hand...so over the workbench is much better than over the MB.

Now I just need to work on a techstation or horizontal case someday.....:D

http://img377.imageshack.us/img377/5...testingmm5.jpg
08-13-2008, 04:22 PM
twwen2

Quote:

Originally Posted by Martinm210

Now I just need to work on a techstation or horizontal case someday.....:D
[/IMG]

http://www.microcool.it/english/101prod.html

You know you want it ;):D
08-13-2008, 04:26 PM
NaeKuh

Quote:

Originally Posted by twwen2

http://www.microcool.it/english/101prod.html

You know you want it ;):D

oh dayam i want that.

okey so who do i need to kill in blingsville to get one? :rofl:
08-13-2008, 04:34 PM
Webby

From the website North American retailers

http://www.microcool.it/english/NordAmerica.html

include Sidewinder, frozen CPU and performance PCs
08-13-2008, 04:38 PM
inonefly

Quote:

Originally Posted by mcoffey

One thing I did notice, the quad core insert is worthless on the V2. I have to go back a run another couple of mounts with the insert to be sure, now that I have the new temp monitoring set up (thanks to your direction and advice), but everything I've seen so far suggests worse performance using the insert. At least on a Yorkie.

Have you seen that also?

andyc

I removed my v2 quad insert last week, I run prime95 for 2 hrs and recorded the temp, then removed the insert and bleed, prime95 2 hrs, I got the same load temp but that's with 2c room temp rise, so i think the quad insert provides worse result on a quad ( q6600 3.6@1.36v)--at least in my setup.
08-13-2008, 04:49 PM
NaeKuh

Quote:

Originally Posted by Webby

From the website North American retailers

http://www.microcool.it/english/NordAmerica.html

include Sidewinder, frozen CPU and performance PCs

Gary carries it?

Then its mine.

Hank does not have that. I should know, when im bored i always go though his site since he's one of the largest. :rofl:

Edit: i have just emailed gary asking him to special order me one. So when i get it i'll show it off. :up:

Hehe.. dont underestimate my budget on computer parts. :rofl:
08-13-2008, 05:19 PM
NaeKuh

Quote:

Originally Posted by mcoffey

Just checked all 3 and didn't see it in stock or that they carried it. I did just send a email to SW. I'd imagine it will cost a pretty penny though. With something as functional and nice looking as that, who'd want a case.

andyc

:rofl: :up:

i found the replacement to my MM.

Dont let R3 hear me say that tho.

If Gary can special order it. Its so mine.

Andy did you check out my lastest usless purchase? :rofl:
08-13-2008, 05:24 PM
Xilikon

Quote:

Originally Posted by NaeKuh

nozzles are missing the cores then on the yorkfield.

planning was done on kentsfield then, and the smaller yorkfield package is missing the injector path.

I'm curious to have the definitive data backing this claim. If it really does, I'll have to put the stock midplate back on my v2 which is cooling my Yorkfield Q9450.
08-13-2008, 05:30 PM
Martinm210

Quote:

Originally Posted by twwen2

http://www.microcool.it/english/101prod.html

You know you want it ;):D

Now why did you have to go do that....been going through keyboards left and right around here...need a waterproof one..!!:yepp:
08-13-2008, 05:40 PM
gillbot

Quote:

Originally Posted by NaeKuh

Gary carries it?

Then its mine.

Hank does not have that. I should know, when im bored i always go though his site since he's one of the largest. :rofl:

Edit: i have just emailed gary asking him to special order me one. So when i get it i'll show it off. :up:

Hehe.. dont underestimate my budget on computer parts. :rofl:

:shakes::shocked:
08-13-2008, 05:42 PM
gillbot

http://www.vr-zone.com/articles/Micr...asts/5980.html
08-13-2008, 05:53 PM
nikhsub1

Quote:

Originally Posted by mcoffey

Oh my,

I think I just felt something happen to me.

ROFL, Andy seriously, I was in a car wreck and my back is killing me. Please now :rofl::ROTF:
08-13-2008, 06:04 PM
Xilikon

Quote:

Originally Posted by mcoffey

You can test it yourself right? That way you can see which plate works best with your loop.

Just a thought,

andyc

Yeah, I know but I'm being lazy :rofl: At least, give me some slack since I started training last monday (need to get up to shape).

I will probably do it when I have time to do a full disassembly for cleaning then see if it improve with the stock nozzle.
08-13-2008, 06:37 PM
twwen2

Oh noes now look what i've done! I gave nikhsub1 a bad back and something's happened to andy!:eek: :rofl::rofl:

Now all we have left to test the GTZ is Martin! :D:p:
08-13-2008, 06:47 PM
NaeKuh

Quote:

Originally Posted by Xilikon

I'm curious to have the definitive data backing this claim. If it really does, I'll have to put the stock midplate back on my v2 which is cooling my Yorkfield Q9450.

pure speculation.

thats what im thinking. Sorry if you think i ment it as fact.

Ugh... one day Xilikon, i shall have that keyboard on your avatar. You just wait.
08-13-2008, 06:51 PM
gabe

Quote:

Originally Posted by NaeKuh

:rofl:

in your own world my friend. EK > D-tek. Can we just end it?

My EK will probably spank this GTZ even. Well im using custom accelerators. :rofl:

My Cuplex will probably beat this GTZ as well, thats if martin finished stepping it.

Gabe you need to step the block and not bow it. Scott definitely discovered a winner.

Only problem tho, once stepped the block can never be used on neha since the die package is different.

Stepping was meticulously tested. Our block design is evidence of the route we chose based on our test data.
08-13-2008, 06:57 PM
twwen2

Quote:

Originally Posted by NaeKuh

Gary carries it?

Then its mine.

Edit: i have just emailed gary asking him to special order me one. So when i get it i'll show it off. :up:

Aww man, now everyone else is gonna get one before me, not fair :(.
Should have kept it all to myself :p:
08-13-2008, 07:26 PM
majestik

Quote:

Originally Posted by NaeKuh

:rofl:

in your own world my friend. EK > D-tek. Can we just end it?

My EK will probably spank this GTZ even. Well im using custom accelerators. :rofl:

My Cuplex will probably beat this GTZ as well, thats if martin finished stepping it.

Gabe you need to step the block and not bow it. Scott definitely discovered a winner.

Only problem tho, once stepped the block can never be used on neha since the die package is different.

If you're so confident in your top secret EK mods... would you mind, you know, posting them? :p:
08-13-2008, 07:27 PM
twwen2

@R3: I know that, there was even a thread here about it in the news section. I was joking you know...;)

The only issue i can see would be noise. Being a benching station, there's nothing stopping those pesky decibels getting to my (annoyingly sensitive) ears :rolleyes:.

Show 100 post(s) from this thread on one page