Printable View
yeah, sorry to burst your reference board hating bubble but there have been plenty of 550+ benches and my board was 500FSB stable out of the box within 5 minutes of first POST. the board is pretty straight forward and doesn't give much fuss getting up to 500FSB. haven't really tried pushing it yet either as i am working with some memory...8-7-6 clocks are coming up though so we'll soon see what my EVGA board does ;)Quote:
Originally Posted by saaya
Finally, a full review with BIOS tuning and stuff of the S2E from AT, woot woot, wish I could get my new board this weekend to play with. Oh well.
hmmm are you sure its not a dud board or something? :/Quote:
Originally Posted by TheHardCase
what voltages did you use?
maybe too much chipset voltage damaged it or something?
Which is the best bios for eVga 790i Ultra¿?¿?
Regards!
Vfsb to the maximum and Vspp to about 1,45-1,5V.Quote:
Originally Posted by TheGoat Eater
Here my E8400 on the XFX. Couldn't get that "stable" for even 10 seconds on my DFI DK P35-T2RS. Can't go any higher, bcs. the limit of the cpu kicks in.
http://www.abload.de/img/xfx_prime_525fsb6yb.jpg
Are you sure it's your board? It could be your CPU or Memory. Read about the degraded affect on the E8x00 CPUs (when they are OCed with lots of voltage going through them). Your CPU may be the culprit.Quote:
Originally Posted by TheHardCase
I have no idea what happened saaya, it was working great. i left it running over night & got up in morning, it was locked up.Quote:
Originally Posted by saaya
So I rebooted & it would not post, this was the same setting used from day 1 that worked.
Vcore 1.39 never ever used more then 1.40 Vcore
VDimm 2.06 never used more on the new 1800MHz Viper, 1600MHz ok I Killed..
NB 1.44
SB 1.50
CPU VTT 1.33
CPU PLL 1.50
After 2 hours playing around with bios ect, now it's working again OMG.
Running for 5 hours so far, man I just don't understand.
hmmmmm reminds me of the striker1... one day a config works... then it doesnt... then changing stuff around but then returning to the same configuration as originally, it suddenly works again. its the same on evga 680, so its the chipset, but on the striker it was way worse than on evga.
i never managed to find out what i had to change to be able to get a config to work again... it all seemed to be very random...
I ran everything at stock, i tried one boot and some small fft with 475fsb and it worked fine for 30 mins, i tried blend and it stopped within a minute, but i returned everything to stock when the board died.....ram was at 1.9v, cpu was at 1.39v, nb was at 1.5, sb was at 1.55v nothing too crazy....i ran these settings for 30 mins of prime95 and returned it to stock and it died...........Quote:
Originally Posted by saaya
EDIT: i got my new board today, when i get home from work im going to put it together, ill report back with some results.
thats not right man... thats not right...
people with such a fine chic in their avatar such as you dont deserve to have a board die on them like that :D hehehe
well your sure it died?
the striker 1 boards went into deeeeep chomas every now and then, most of the time showing cpu init and thats it :D but eventually some of them came back to live... after some time and trying again and again and doing some voodoo dances :D
And not to forget...sometimes you had to remove any power from the board ( that means leave the board alone, with nothing plugged in and with the CMOS battery removed ) for 3-6 hours.Quote:
Originally Posted by saaya
Oh well, this is going from bad to worse to death... >_>!
hehehe, thanks bro ;)Quote:
Originally Posted by saaya
Yeah bro, i even tried it one hour later, it tries to turn on, let me try to explain it the best i can, a slight power goes into the system then it just shuts right off, my led fan will spin once and wont fully power up, i thought it was my psu in the beggining, but its a brand new antec 850w quattro, much harder to kill a quality psu than a board.....ive droped screws into my psu's and they didnt die!!! it even sparked, and it still works, enermax liberty, thats one heavy duty psu.
Let me get this straight.
You try to power on the board... it "fires up" for a sec ( or half a sec :p: ) and automatically shutdowns.
If you press the power switch again, does it power up again or doesn't do anything ?
Because the second thing is saying "Short-circuit...somewhere" [ and short-circuit could also mean dead hardware ]
It happens from time to time on my S2E,whenver I shut down completely and then restart after some time. But as soon I pull the plug off my PSU and leave it alone for a few minutes and plug it back in, it works.It also works when I push the clear CMOS button.Quote:
Originally Posted by GAR
I'll cancel my Maximus auction on Ebay and keep it for a few more days after I get my SIIE. You guys are freakin' me out w/ these horror stories!! Seriously, is there anybody happy with this board??
595MHz stable FSB on SS phase :DQuote:
Originally Posted by saaya
on water i've done some 575MHz 32M runs
but it really depends on the chips
and it does take a little while to tune it right as well as i've had times during testing where it won't boot at 525 with another chip lol (vcore wasn't in the right range ;))......you do have to hit sweet spots if you are on air/water for volts >> for air/water you have to tune GTLRef a little as well as volts to get what you want out of the FSB
if you have subzero it is waaaay easier....you just bump the volts and just start from 550 in 5GHz incrememnts (all booting from bios)
i can boot at 611MHz i think it was (~5.8GHz) but FSB isn't stable
charles is perfectly stable at 600MHz FSB with his E8400 chip :shrug:
WTF GAR
another dead board
something is very odd there :S
i have tested my Corsair 1600MHz CAS7 4GB(2x2GB) kit at 1.95v or 2v can't remember and i could do superpi 32m at 850MHz 7-7-7-20 1T :up:Quote:
Originally Posted by GAR
Hopefully I will write an story of my own experience with the board soon...Quote:
Originally Posted by golfjam
I'm starting to be happy with mine, As a few have said on here the SE2 takes a bit of learning to get it stable, I did notice a lot more stability after I started Watercooling the NB. So far I have it prime stable at 4 GHZ and I'm starting to ease it up from there. I'm using the voltages Justfire posted btw.
What are your specs? CPU, Memory, etc??Quote:
Originally Posted by Fusion2002
yup, just found the 'lazy' FSB limit of my good E8400...it's never a bad thing when the CPU FSB is holding up your memory :DQuote:
Originally Posted by dinos22
just have to insulate the board sooner than i thought i would have to. gotta love the sub 12m dual 32m on air without any tweaks ;)
click for full size...
http://img.photobucket.com/albums/v2...6_1060-1sm.png
SIIe with stock conroe's hsf...
http://img502.imageshack.us/img502/8...shot002cf0.jpg
http://img516.imageshack.us/img516/2...shot004hi1.jpg
nice going Dumo :)nice manQuote:
Originally Posted by 3oh6
increase your CPU voltage to 1.55v in bios
and try again for max FSB
bump MCP volts to 1.75v and also play a little with GTL values
i've had more luck lowering them to -110 on watercooling when i got stuck before
I can't seem to break over 10k on my Memory read/writes at all. I'm running 1T on my black slots at 7-7-7-20 1600 MHZ of Patriot memory.
Anyone have suggestions?