Hi,
I am using a single 8800GT-512, a Leadtek reference card. Occasionally my card doesn't get initialized and the system starts, but a simple reset gets this straightened out again. I cannot blame that specifically on the board, the conversion OR the card's modified BIOS (GPU:800, RAM 1900, shader: 1700) tho...it just sounds similar. I hope this helps any...
Quote:
Originally Posted by WFO
Thanks Talonman. I pulled it but no joy. If I'm not even showing a post screen, drivers haven't even had a chance to load so I wasn't expecting that to work. Desperate times. Desperate measures. :up:Quote:
Originally Posted by Talonman
I wish it were that simple. :) It doesn't matter how many times I reset or clear cmos. Nvidia= black screen. :( I'm not going to spend a lot of time on this. My guesses were my DVI KVM. Plugging the monitor in directly equaled black screen too. Or my Armor case just doesn't let Nvidia cards sit right in the slot. I have too much time in cable management and a dual-rad water loop to tear it apart for experimentation. :rolleyes: This rig will keep ATI and MY P5K Deluxe and P5Q rigs will get the Nvidia cards.Quote:
Originally Posted by Amurtigress
I've followed the Maximus Formula and Maximus Rampage threads from the beginning. I'm the only one I've read about with this problem. :( It never hurts to ask though. :)
What is the typical max FSB achieved with this board with a dual core wolfdale and then after conversion to rampage formula?
is there a significant gain in FSB?
what!??Quote:
436/8*9=490 MHz
are you saying one setting you use is 436 FSB 8x cpu multi
and another seting you use is 490mhz fsb and 9x cpu multi ?
if not then i do not understand where your getting those numbers.
the FSB is what it is,, its not times or divided by anything else...
400mhz FSB is 400MHz whether you use a 6x multi or a 10x multi. all the multi does is simply increase your default cpu speed.
cpu multi also doesnt change your ram speed
OR are you saying your ram is 490mhz ???
thus 436x8 = 3488
436x9 = 3924
490x8 = 3920
490x9 = 4410 - and you are not doing that with this board unless its a dual core. you wont do 490 x 9 on a quad with this board. not on air or water atleast.
WOOHOO!!!
1207 makes the mobo see my Q9650 (ES) properly along with temps properly (in the bios) and no more stupid unsupported cpu warning everytime the system boots!!
now i have to start playing with voltages be this E0 cpu should be doing a better overclock than 3.825 @ 1.28v
http://valid.x86-secret.com/show_oc.php?id=404154
and the best part!! i can now adjust my cpu multi!!!!!! time to get to FSB testing!
i also can FINALLY stress out this OZC Reaper 9200 stuff which is just absolutely wicked ram. 1133mhz 2.0v ?? i mena come on thats crazy 5-5-5-12
Hi,
I sort of saw that coming. has noone here had a P5B Series board before?
You should read the article on FSB straps and NB clocks on the P965 chipsets. I don't have hard evidence so far that the X38 is behaving the same, but the intel chipsets are all VERY similar. They just evolve bit by bit but don't ditch their whole architecture. The northbridge clock on P965 chips is calculated the following way:
NB core clock = (CPU max multiplier / CPU current multiplier) * FSB clock
ex. if you are running a E6600 at 3.6 GHz, you have the option to use 400*9 or 450*8.
The NB however runs at either 506 MHz (9/8)*450 or in the latter case at (9/9)*400.
This is also the reason why you should disable speedstep whenever you are overclocking. The further the multiplier goes down, the more the NB cklock goes up with the FSB clock remaining constant. At some point the voltage for the NB core gets insufficient and the computer crashes.
There was a good article on xtremesystems, on FSB straps on the ASUS P5B Deluxe board. Trying to hunt it up and add the URL to the posting as soon as I find it.
--- Edit! ---
Here is the article:
http://www.thetechrepository.com/sho...hp?p=32#post32
------------
Quote:
Originally Posted by Lestat
I would also like to know.. but from what ive seen i think there is a gain in fsb and some memory settings.Quote:
Originally Posted by shimmishim
Asus got back to me as well - looks like it's another direct replacement as well. Oh poo. Stingy gits!!!
Got my E8600 but I lost a bit for my CPU block so no OC'ing yet >.<
New equipment for next month anyway :D
~Bex
Do you mean, 1333? 'cos I can get 1175 with 8500 2x2GB G.Skills.Quote:
Originally Posted by Lestat
Could I get you BIOS settings?Quote:
Originally Posted by Grnfinger
Ai Overclock Tuner : ManualQuote:
Originally Posted by ShawnTRD
OC From CPU Level Up : AUTO
CPU Ratio Setting : 8
FSB Strap to North Bridge : 333
FSB Frequency : 450
PCI-E Frequency: 110
DRAM Frequency: DDR2-1080mhz
DRAM Command Rate : 2N
DRAM CLK Skew on Channel A: Advanced 250ps
DRAM CLK Skew on Channel B: Advanced 250ps
DRAM Timing Control: Manual
CAS# Latency : 5
RAS# to CAS# Delay : 5
RAS# Precharge : 5
RAS# ActivateTime : 15
RAS# to RAS# Delay : 3
Row Refresh Cycle Time : 55
Write Recovery Time : 6
Read to Precharge Time : 3
Read to Write Delay (S/D) : 8
Write to Read Delay (S) : 3
Write to Read Delay (D) : 5
Read to Read Delay (S) : 4
Read to Read Delay (D) : 6
Write to Write Delay (S) : 4
Write to Write Delay (D) : 6
3rd Information
WRITE to PRE Delay : 14
READ to PRE Delay : 5
PRE to PRE Delay : 1
ALL PRE to ACT Delay : 5
ALL PRE to REF Delay : 5
DRAM Static Read Control: Enabled
Ai Clock Twister : Stronger
Transaction Booster : Manual
Performance Level 7
CPU Voltage : 1.40
CPU PLL Voltage : 1.50
North Bridge Voltage : 1.51
DRAM Voltage : 2.12
FSB Termination Voltage : 1.20
South Bridge Voltage : 1.05
SB 1.5V Voltage : 1.50
Loadline Calibration : Enabled
CPU GTL Reference : 0.65X
North Bridge GTL Reference : 0.67X
DDR2 Controller REF Voltage : DDR2-REF
DDR2 Channel A REF Voltage : DDR2-REFF
DDR2 Channel B REF Voltage : DDR2-REFF
So I have been reading for awhile and I have searched the thread, but I cannot find what I am looking for, even under the first page sticky.
1 - What does flashing your Maximus bios to a Rampage bios get you?
2 - It looks like if I stick with the Maximus bios it should be the 1102, is this correct?
3 - If I flash to the Rampage then I should use 1207, is that correct?
Thanks,
Utnorris
1207 is the current MAXIMUS bios, 407 is the current RAMPAGE bios.Quote:
Originally Posted by Utnorris
thay are released for the new cpu stepping on the E8600 and Q9650.
Flashing your Maximus to Rampage will yeild higher FSB and lower volts.
most ppl are seeing around. 25-45fsb increase and 2 notches less of vcore.
308 Rampage bios is the best so far for bandwidth. 407 is not a bad bios but if you dont need it I would not run it, I like 308 , it has a higher tref value and is a really stable bios.
Also the det dram hang is a thing of the past cause you can manually set your PL level, Clock Skew is another handy feature which allows for higher ram overclocks while maintaining stability
what this S or D
Read to Write Delay (S/D) : 8
Write to Read Delay (S) : 3
Write to Read Delay (D) : 5
Read to Read Delay (S) : 4
Read to Read Delay (D) : 6
Write to Write Delay (S) : 4
Write to Write Delay (D) : 6
And what can I use to read what my MB did doing for AUTO? I'm using Memset, but it's not telling my all my Memory settings.
Hi Guys,
I must say that i did tryed the search, but didn't find ...
After flashing my mobo Maximus Formula, with the 403 bios - to rampage, the LCD Poster - blinks all the time, with the clock.
Sometimes windows starts, and everything is ok, but after ( nothing ) it blinks, blinks and blinks ... until i reboot computer, even in bios sometimes it starts the blink - ... I tryed every little config to find out what was the problem, but ... no way. I can't imagine, what is the problem.
using as stock maximuls formula, never happened, just after the conversion !!!!
Anyone knows anything about this !?!?
I don't use the LCD Poster, but did you reset your CMOS?
aqui funcionou de boa... Enfim...Quote:
Originally Posted by wander_jarra
407 was even worse then 403 for overclock, around here, higher voltage on NB ans Vfsb for lower stability.
I have a Q9650, i have a Maximus Formula SE and im trying to flash my board to a Rampage. Im trying to flash to the 407bios and it says to me that it cannot open the bios. Has anyone tried to flash to this bios? Do i need a modded one? Thanks.
most likey its a syntax error.Quote:
Originally Posted by Nunzi
Make sure you type in uppercase
/AFUDOS /iRF0407.rom /pbnc /n
so rename your bios 407 to RF0407 and it should work
Use the AFUDOS v2.29ES not the v2.36ES. Plus I suggest using 0308:up: BIOS over 0407:down:.Quote:
Originally Posted by Nunzi
you cant use 308 on that chipQuote:
Originally Posted by ShawnTRD
Thanks guys for all your help.........got it flashed to 0407
Let us know how they work for you.Quote:
Originally Posted by Nunzi