Printable View
From Newegg.
http://img234.echo.cx/img234/2428/core2he.jpg
http://img157.echo.cx/img157/8484/1079696qd.jpg
It can be possible that mo board does not allow me to control but of 317 mhz of HTT?
I have not managed to improve it of this point :slap: .
Until soon
Testing fore a friend , haven`t seen this APLW before, anyone else ?
http://home.online.no/~andr-sei/Fosc...oldis3000+.JPG
LANero.. try putting max async in bios to auto.. and try again..
guide is here :) http://i4memory.com/showthread.php?t=327
Nope, I haven't...just as I still haven't seen anyone else with my 0516 EPKW. Oh well, they're not missing out on much...300x9 at 1.728v and nothing less for voltage...temp limited like nothing I've ever seen.Quote:
Testing fore a friend , haven`t seen this APLW before, anyone else ?
Thank you very much by the suggestion babyelf ;) .
I have tried to put the MAX Async Lat in AUTO but as soon as attempt to pass of 317mhz this is what I obtain :slapass: :
yea.. that's what i have been getting as well..
play around with ur drive strength + max async and read preamble
go down in the guide.. and u'll see his results with different max async + read preamble
erm why my pc reboots when i try OCCT or PRIME but it does super pi ok...
example 325*9 at 1.6v (cpu-z)
yea.. same.. venice + prime does not go very well.. duno y
everything else is stable.. superpi games etc.. just prime.. so i discarded it as a stability test
This information is VERY IMPORTANT!!!! If is true .....suxxxx!!!! :mad:Quote:
Originally Posted by arj
babyelf
320Mhz on board :clap: .
http://img107.echo.cx/img107/2372/291888lu.jpg
Not yet he is 100% stable one, but at least already I can run pi of 1M.
The only form to obtain to this fué leaving Tref, Twr, Twtr, Trtw, etc in AUTO and starting in 320 Bios from giving this is the result.
http://img166.echo.cx/img166/3919/tweaker1qp.jpg
Thank you very much by your aid friend
no problem.. try playing with max async latency and read preamble..
read eva's guide :)
erm what has memory timings to do with cpu ocing ? :)
http://i4memory.com/showthread.php?t=327
check here.. with differnt max async + read preamble superpi passes more or less depending on different settings :)
I am going to give an attempt to this and hope to return with better results.
I believe that this CPU needs a little burn to improve.
Until soon
Memory timings play a major role in oc. As does the ability to remove heat from the cpu. Colder cpu = easier oc. This was 0516 FPAW and I never took the time to see if it could do more, i.e. with like a 10X multi or just more HTT. [IMG]http://img22.echo.cx/img22/6715/3ktwk2fc.jpg[/IMG]
[QUOTE=coop]Memory timings play a major role in oc. As does the ability to remove heat from the cpu. Colder cpu = easier oc. This was 0516 FPAW and I never took the time to see if it could do more, i.e. with like a 10X multi or just more HTT.[...]QUOTE]
Well done coop :toast:
What cooler are you using? Tamb at??
11C, i'm guessing chilled water
very cold water, I used my water cooling setup and replaced the fans with a block of dry ice for that.
Thanks for the photo, I was thinking about wc, but I see the fan control on the screen and so I've guess very cold temp ambient :D
Quote:
Originally Posted by coop
which CPU block ur using? and ur motherboard and cpu arean are isolated?
0517APLW , watercooled.
http://home.online.no/~andr-sei/Fosc...venice2799.JPG
It is a copper ingot from Swiftech (6002). It is fairly large and heavy, but removes heat very well and is very affordable. Yes, I painted with liquid electrical tape around the cpu area. Then, foam insulation and grease. I would suggest reading about condensation proofing, I don't know if this is the place to be discussing it. It is most important as when it starts to form it quickly becomes out of control and forms anywhere air is exposed to the cold. If it is around anything electrical that is not protected you could loose your board and or cpu. You can PM me if you like.
After the Burn of 2 Hours.
http://img234.echo.cx/img234/5855/1m0291723gf.jpg
I continue trying to obtain but stability.
Where is the best place to order a Venice in hopes of getting a good stepping?
Also, would a 3000+ or a 3200+ have a better stepping?
Thanks