does this board suffer from S3 sleep issues like the gigabyte ones.
Printable View
does this board suffer from S3 sleep issues like the gigabyte ones.
Not that i've had or ever seen anyone post about.Quote:
Originally Posted by strange|ife
I have had a weird issue where the HDDs on the Marvell SATA ports don't show up after resuming from sleep, but it could very well be just me as i am using the default drivers Vista loads & haven't really looked into it at all (i don't use sleep anyway).
i got plenty on free hard drive space and also virtual memory... tried 2 different versions of vista 64 and it keeps doing it .... might try 7 later on
Quote:
Originally Posted by strange|ife
No. Even if you're transferring an old installation that didn't have S3 set up correctly, there's an option in the BIOS to force S3 sleep whenever a sleep mode is initiated - everything goes off including case/CPU/power fans, even if your OS is only set to do S1.
its still happening even after i installed windows 7 64b after getting really angry and throwing my keyboard around lol... i researched a bit and realized that i had running on the task manager svchost.exe like 7 times and one of them was sucking all my ram 158,000 K under the memory on task manager apparently there are viruses that can hide behind that host process for windows services.... :confused: anyway i honestly don't know what to do... :shakes:
Lower ya OC and see if it then still persists... try just eg 400FSB with rams at 1000mhz or 1066...
It does it wherether I OC or not mate it might be same kind of virus that has copied after i installed the New OS... windows 7 is great
Or a virus in the file(s) you are working with ? Seems weird indeed as I have compressed decompressed large movie and Iso files on just 2gb ram rigs...
Honestly, try a different bios. Sounds like what was happening before I got my OC stable after I went with 8GB. I was HCI Memtest and IBT stable but would have odd issues and just wouldn't dump ram. So it would just sit at like 7+ GB of ram being used then slowing down.
Hi,
I just installed a SSD (intel x-25m 80gb). I have windows 7 x64 ultimate installed on the SSD.
I got this result with HD-tune,
HD Tune: INTEL SSDSA2M080G2GC Benchmark
Transfer Rate Minimum : 98.8 MB/sec
Transfer Rate Maximum : 131.5 MB/sec
Transfer Rate Average : 127.2 MB/sec
Access Time : 0.1 ms
Burst Rate : 97.2 MB/sec
CPU Usage : -1.0%
What is wrong? My board P5Q Deluxe support SATA2, but it goes as SATA1? Is this a BIOS setting issue?
well there isnt a virus on the rar file all they are is pictures am trying to un rar lol i might try to get an external HHD and back my stuff on it and then do a complete format of C see what happens cheers
I have 2x1GB crucial ballistix tracer 8500 ram and currently running the settings posted below. I recently bought 2 more 1gb sticks of the same ram and trying to get the system stable again.
any tips on settings i can loosen to get it stable fast? at the moment i can get into windows and burn cd's etc but memtest fails straigh away. any help appreciated
AI Overclock tuner: Manual
CPU Ratio Setting: 9
FSB Strap to North Bridge: 333
FSB Frequency: 478
PCI-E Frequency: 101
DRAM Frequency: 1148
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: Manual
1st Information :
CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 15
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time: 55
Write Recovery Time: AUTO
Read to Precharge Time: AUTO
DRAM Static Read Control: Disabled
DRAM Read Training: AUTO
MEM. OC Charger: AUTO
AI Clock Twister: AUTO
AI Transaction Booster: Manual
Common Performance Level: 10
CPU Voltage: 1.41875
CPU GTL Voltage Reference (0/2): AUTO
CPU GTL Voltage Reference (1/3): AUTO
CPU PLL Voltage: 1.6
FSB Termination Voltage: 1.3
DRAM Voltage: 2.14
NB Voltage: 1.26
NB GTL Reference: AUTO
SBridge Voltage: AUTO
PCIE SATA Voltage: AUTO
Load Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : Auto
NB Clock Skew : Auto
so i finally sent my board in for rma last week, site shows they received it and are in final testing. i hope they just send me a new one, and by that i'm assuming refurb.
hoping they do me right!
Bootable Memtest86/86+ failing?Quote:
Originally Posted by aiya_au
It is LinX/HCI/P95 stable?
Your issues might be NB related also?
You might want to look at setting Clock Twister manually.
I find at higher speeds with 8 GB at least, it needs to be @ Light or Lighter, whereas it can do Moderate at lower speeds.
Also maybe try enabling Read Training & OC Charger.
I'd say you may need more NB voltage considering how high your FSB is.
I havn't tried prime yet. i usually get the ram stable before i enter windows because i've had bad experiences corrupting my windows install with unstable ram.Quote:
Originally Posted by -n7-
I tried increasing the NB voltage to 1.3v, clock twister to light, PL to 10. didn't help get it memtest86+ stable. would Read Training & OC Charger help much in terms of stability?
I've so far got it all stable at 4.2ghz by dropping the FBS to 467mhz and in the process reduce the vcore, vram. i figured i wont notice a 100mhz hit and lowering the voltages is a good thing.
i'll try out your settings sometime this week when i have more time. thanks though :up:
Guys, have you noticed this disparity? Some P5Qs need 1.2x voltage to do 500fsb with a quad, and others (Like mine) need 1.5v+ to do 500fsb. Is that alright? My NB doesn't really go past 40c "Blend" priming at 1.5v... but I don't know how much the P45 can take without degrading.
agreed, mine has a great revision.
so asus is sending me a new serial number from the board i sent in. the number looks to be much later than the one i sent assuming they number them in order.
are there different revisions to the p5q deluxe?
Hello everybody.I have a q9650 and a p5q deluxe and i cannot hit more than 3.8ghz on cpu(425fsb).Can you help me please to reach 4.05ghz(450fsb)by giving me some settings?
Plz fill in this template ( P5Q DLx template) Hydrus with ya current setup
also list ya full hardware plz ( ram and their specs, cooling, etc)
Dunno about revision nrs mentioned on the PCB itself, but the newer models got the newer revision of the NB like the Gigabyte UD3P models have...Quote:
Originally Posted by Brandito
AI Overclock tuner: enabled
CPU Ratio Setting: AUTO
FSB Strap to North Bridge: AUTO
FSB Frequency: 425
PCI-E Frequency: AUTO
DRAM Frequency: 1133
DRAM CLK Skew on Channel A1: adv350ps
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: adv350ps
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: manual
1st Information :
CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 15
RAS# to RAS# Delay : 5
Row Refresh Cycle Time: 60
Write Recovery Time: 6
Read to Precharge Time: 3
2nd Information :
READ to WRITE Delay (S/D): 10
Write to Read Delay (S): 3
WRITE to READ Delay (D): 4
READ to READ Delay (S): 6
READ to READ Delay (D): 5
WRITE to WRITE Delay (S): 5
WRITE to WRITE Delay (D): 4
3rd Information :
WRITE to PRE Delay: 13
READ to PRE Delay: 6
PRE to PRE Delay: 1
ALL PRE to ACT Delay: 6
ALL PRE to REF Delay: 6
DRAM Static Read Control: Disabled
DRAM Read Training: DISABLED
MEM. OC Charger: ENABLED
AI Clock Twister: moderate
AI Transaction Booster: AUTO
Common Performance Level [10]
Pull-In of CHA PH1: ENABLED
Pull-In of CHA PH2: ENABLED
Pull-In of CHA PH3: ENABLED
Pull-In of CHA PH4: ENABLED
Pull-In of CHB PH1: ENABLED
Pull-In of CHB PH2: ENABLED
Pull-In of CHB PH3: ENABLED
Pull-In of CHB PH4: ENABLED
CPU Voltage: 1.287
CPU GTL Voltage Reference (0/2): AUTO
CPU GTL Voltage Reference (1/3): AUTO
CPU PLL Voltage: 1.50
FSB Termination Voltage: 1.22
DRAM Voltage: 1.96
NB Voltage: 1.22
NB GTL Reference: AUTO
SBridge Voltage: 1.10
PCIE SATA Voltage: 1.50
Load Line Calibration: ENABLED
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : Normal
NB Clock Skew : Normal
CPU:INTEL Q9650
MOTHERBOARD:ASUS P5Q DELUXE REV. 1.03G
RAM:4GB MUSHKIN SP ASCENT 1066(they can hit 1190mhz with 2.1v and 1200 2.2-2.3volt)
GFX CARD:SAPPHIRE 4870(512mb)
POWER SUPPLY:CORSAIR TX750W
CPU COOLER:THERMALRIGHT ULTRA 120 EXTREME
HDD:WD CAVIAR 640(blue)
Try the above mate, save ya current setup and then put all mem and subtimings to auto again besides 5-5-5-15 TRFC 55... then apply above changes... could be that for +450 FSB action you need to go higher on the FSB term volts...Quote:
Originally Posted by Hydrus
I will try and i will inform you about the results.Thanks :) i would like to ask you something more....will be any problem if i use cpu ratio 9 instead of 8?Of course after increasing cpu voltage...
I would try first 7X or even 8X multi mate, just to rule out CPU Vcore... quads are harder to setup on these mobo's...
OK i will try and i will inform you...;)