what should be good 24/7 settins for this rams ?Quote:
Originally Posted by chew*
Printable View
what should be good 24/7 settins for this rams ?Quote:
Originally Posted by chew*
Anything over 3.8 gig cpu is going to benefit best with ram around 1800 6-6-6 at no more than 1.72v to ram to extend its lifetime.Quote:
Originally Posted by Hirogen
Which mobo? DIMM voltage? :)Quote:
Originally Posted by tsan
quoting tsan from hwbox.gr :D
its msi 890fxa gd70 and 1.825 vdimm:)
My Elpida hyper can reach 6-6-5-15 1T at 1600 (2000 / 7-7-8-21) at 1.7V. But one day suddenly it died.................:(
The model was G.SKILL Perfect Storm 6GB Triple kit - I used it on AMD 890FX, used only two, reserved one for emergency use.
(Fast review on that memory: http://udteam.tistory.com/123)
(The review is written in Korean - sorry for that, but I'm sure everyone is able to understand it via screenshots :D)
Just like mine 2000MHz CL8 old kingston kit can do 6-5-5-15 1T 1600 but this kit needs 1.725-1.75v to get it pass 32M superpi32M.Quote:
Originally Posted by DGLee
Was ur kit GMH-e or NMH-e?
I don't know cause I've never taken heat-spreader off. :p:Quote:
Originally Posted by SeMbEr
mine 2000c8 corsair can do ~1840 6-6-5-17 @ 1.82v :D on asus c4e
fed them with 1.93v to see what will happen but cant stabilize them @ 1600 5-6-5 :(
Wow 1.93V is quite a lot for Hypers i think! Not degraded after that?
nah, hypers aren't that fragile.
i've a set of kingston that run at least 200 hours (most of them with intel 1366) at 1.95 volt in the past year and till now no degrading or dead stick.
tsan, which bios of the MSI 890FXA-GD70 did you used?
funny how kingston hypers are so much betterQuote:
Originally Posted by Mafio
i pumped upto 1.9v in mine n there were are good as day 1 ti'll i sold em
thanks tsan, this WE i will retry the board.Quote:
Originally Posted by tsan
is this a Good/ Bad/ OK RAM for AMD?
Super Talent 1600 9-9-9-25 but i'm running it at 8-8-8-25-1T
http://i.imgur.com/TaH3K.png
boot time seems to be affected with timings?
http://i.imgur.com/JI7r0.jpg
How much ram is this? For 2x4gb its... ok. for 2x2gb its meh.
Same as here, I think you can go further.Quote:
Originally Posted by duron
Super Talent 1600Mhz C8 BULL3T - Limited by B4RR3L
http://i53.tinypic.com/fbgn40.jpg
http://i53.tinypic.com/2ppzuag.jpg
http://i51.tinypic.com/30sjcja.jpg
http://i54.tinypic.com/15fk37b.jpg
http://i52.tinypic.com/2s159ur.jpg
@Barr3l Rid3r
yeah almost the same with the heat spreader
@liberato87
nice speeds
Liberato, nice, how did you find 1T cmd rate RAM? Thats what im looking for in my next upgrade.
All (pretty much all) ram runs 1T. DDR3 is very different than DDR2.Quote:
Originally Posted by Poci
DDR3-2022 6-6-6-18 validation in my sig is 1T.
Nice!!!Quote:
Originally Posted by liberato87
What DRAM Voltage?
Any idea on which chips are on this one:
F3-17000CL9D-4GBXMD Cl 9-10-9
Link:
http://www.gskill.com/products.php?index=367
1.65v (this kit is rated from 1,55v to 1,75v)Quote:
Originally Posted by PatRaceTin
1840mhz 7 7 7 21 @ 1.65v is memtest stable 300%.
I will not give to much voltage to this elpida hyper kit
That set should be capable of much higher than 1840 at 7-7-7. Is it just the X6 IMC that's limiting you?Quote:
Originally Posted by liberato87
In fact, those A-data kits were generally close to the GTX2 in overclocking performance... wouldn't surprise me if you could do 1850 6-6-6 with 1.7V or less.
Those adata kits were not generally close to GTX2.Quote:
Originally Posted by bassplayer
Worse than the SuperTalent 2200 C8, you could get probably 1700 6-6-6 out of them