Apogee GTZ

Printable View

Show 100 post(s) from this thread on one page

08-06-2008, 08:12 PM
Martinm210

Quote:

Originally Posted by menace2society

To the regular folks :hm:

How long have you had one :hrhr::hehe:

Maybe long enough to post some test results to coincide
with the release?

Now that's Keeping it:pimp:

Regular folks would include me, I did get an email that I may get one when released, but not prior to that.

I purposely asked for a production sample when it is released to the public. I had too many radiators left to test to start my CPU block testing again and make the timeframes they were after on the preproduction samples.

So, nope I don't have one, I don't know anything more than what was posted on the coolingmasters site, which apparently is incorrect anyhow.:shrug:

I am starting in on testing the other blocks I do have finally on this quad core...so if I get one it'll be good timing to work into the rest of the samples testing..:up:
08-06-2008, 11:32 PM
jonny_ftm

Quote:

Originally Posted by Martinm210

Regular folks would include me, I did get an email that I may get one when released, but not prior to that.

I purposely asked for a production sample when it is released to the public. I had too many radiators left to test to start my CPU block testing again and make the timeframes they were after on the preproduction samples.

So, nope I don't have one, I don't know anything more than what was posted on the coolingmasters site, which apparently is incorrect anyhow.:shrug:

I am starting in on testing the other blocks I do have finally on this quad core...so if I get one it'll be good timing to work into the rest of the samples testing..:up:

Now this is great news. Finally a Real review of those EK Supreme, Fuzion V2, Enzotech Rev A and GTZ
My decision to buy a WB, like many of us, will depend on your results :)

Thank you very much for going through that big time consuming expedition
08-08-2008, 01:44 PM
gabe

1 Attachment(s)

1/2" compression fittings

some people asked if 1/4" BSPP to 1/2" ID x 3/4" OD compression fittings work with the block, so here is confirmation that they do. We haven't pressure tested, but a cursory check shows no problem so far.
08-08-2008, 01:46 PM
Everett

*Prints off copy, Heads to bathroom*
08-08-2008, 01:47 PM
jonny_ftm

Quote:

Originally Posted by gabe

some people asked if they fit, so here is confirmation that they do. We haven't pressure tested, but a cursory check shows no problem so far.

1/2-3/4 compression fittings?
Also, would it be possible to extend to Nehalem without changing the whole top and spending a crazy sum of money like for the GTX copper top? That is, will it be possible to release only a top mounting fixing plate?
08-08-2008, 01:53 PM
gabe

Quote:

Originally Posted by jonny_ftm

1/2-3/4 compression fittings?
Also, would it be possible to extend to Nehalem without changing the whole top and spending a crazy sum of money like for the GTX copper top?

All I can promise is that we will try our absolute best to confine this to a simple and painless upgrade, and all I can say is that it looks encouraging so far.
08-08-2008, 02:00 PM
gabe

Quote:

Originally Posted by RealRedRaider

Are the compression fittings pictured 1/2" x 3/4" ??? :shrug:

If so, that's AWESOME ...... :up:

I have edited my post to clarify further. sorry for not being precise enough.
08-08-2008, 02:05 PM
Nate P.

What's that on the NB?:hrhr:
08-08-2008, 02:11 PM
hotdun

Quote:

Originally Posted by RealRedRaider

Gabe, you my man, are alright in my book.............. :up:

Somebody's changing their tune....:eh:

Quote:

Originally Posted by Nate P.

What's that on the NB?:hrhr:

Ditto...
08-08-2008, 02:23 PM
freakgeek1337

Reply

Ya I was curious what's on the NB too, it seems that that's a Maximus II board... Hmm...;)
08-08-2008, 02:28 PM
faster3200

Woah, that is great looking. Assuming it preforms half as well as it sounds I think I have found my new cpu block. It even has bling master approval so far :p:.
08-08-2008, 02:32 PM
SaiNRuB

Gabe, tell me about the chipset block you have seated on the maximus II please!!

Fantastic products brother!!
08-08-2008, 02:34 PM
gabe

Quote:

Originally Posted by gabe

some people asked if 1/4" BSPP to 1/2" ID x 3/4" OD compression fittings work with the block, so here is confirmation that they do. We haven't pressure tested, but a cursory check shows no problem so far.

and I am now confirming that pressure/leak tests passed.
08-08-2008, 02:37 PM
Sadasius

Quote:

Originally Posted by gabe

and I am now confirming that pressure/leak tests passed.

I might switch out my D-Tek then for this one. If it performs just as good or better.
08-08-2008, 03:01 PM
Bojamijams

Whatever it is on the NB it says REPUBLIC OF GAMERS on that sticker..
08-08-2008, 03:35 PM
skinnee

I don't think we're going to be getting any details on the NB block, Gabe has clearly not responded to those questions. Could very well be something he can't release any info on yet or a Swiftech internal use (lab) block only.
08-08-2008, 03:39 PM
IanY

What's that new chipset block?

Compatible with ROG heatsinks too!
08-08-2008, 03:57 PM
skinnee

Quote:

Originally Posted by IanY

What's that new chipset block?

Compatible with ROG heatsinks too!

:rofl:
08-08-2008, 03:59 PM
sirheck

Quote:

Originally Posted by skinnee

:rofl:

Uh gee ya think:D
08-08-2008, 04:09 PM
twwen2

Quote:

Originally Posted by skinnee

I don't think we're going to be getting any details on the NB block, Gabe has clearly not responded to those questions. Could very well be something he can't release any info on yet or a Swiftech internal use (lab) block only.

Yea that's the impression i'm getting too. But he's entitled to secrecy if he wants/needs. If it's for the market we'll know about it eventually.
08-08-2008, 05:38 PM
Nate P.

That wire is for the LED under the ROG logo.

Show 100 post(s) from this thread on one page