"ASUS P5Q Deluxe discussion".

Printable View

Show 100 post(s) from this thread on one page

03-04-2009, 05:12 AM
mreddie

hi. thanks to vrbublo for the help with settings and the link to the gtl settings. i am now stable at 4.0 ghz. it was indeed the cpu gtl ref which helped but i also had to increase the nb volts to 1.32v. i will try to bring this down to 1.30 by playing with the nb gtl ref. volts. i know that 1.28v on nb is unstable.

will continue to tweak a little to see if i can decrease any volts, but thanks to all on this thread for tonnes of valuable info.

my question now is , is 1.32v for the nb safe for 24/7 use? i have 2x 40mm scythe mini kaze fans tied side by side to the nb heat spreaders and i have good airflow (7x noctua npf-12 fans) as case fans but even so, is this a safe voltage for 24/7 use?
03-04-2009, 10:17 AM
vrdublu

Quote:

Originally Posted by Leeghoofd

Why don't you try 445FSB and 1066Mhz on the rams... also for the ram plz set TRFC ( row refresch Cycyle time ) at 55 for 2GB dimms.

And don't put in so high FSB Tern and PLL voltages. Learn how your own CPU's responds to volts.... you tell the story yourself : 1.28 : 1 hour, 1.3 1 minutes : so lower the value then :rolleyes: instead of increasing... think logic !

And if you try tweaking the GTL values (only because it's not stable in Blend ) just trying 0.630 and 0.635 is far from enough... with a quad take your time. A Wolfdale almost doesn't need any NB/CPUGTL tweaking till 550FSB stability (unless the CPU is totally overfed with volts)

In your case I would drop down to 400FSB and learn how to setup the CPU. Get it stable with the lowest values possible of FSB and PLL : testing with prime SMALL FFT !! no IBT plz. Then work ya way up to 425FSB, restest the cpu again. And so on... you guys are all aiming too high from the start and then get lost, copy templates with settings that ( in my humble opinion ) are overkill. And then finally you get frustrated and ditch the board.

P45 needs proper volt tuning, same for the 45nm CPU : MORE VOLTS ISN'T ALWAYS BETTER !!

Start off with FSB Term 1.2, PLL 1.5 and NB Volt at 1.2 at 400FSB/1000mhz ram and most ram timings to AUTO besides 5-5-5-15 TRFC 55, Static Read Disabled.

Hey LEEGHOOFD just curious if you have any suggestions on how I could lower my CPU VTT currently sitting @ 1.36V. The problem I have seen so far is that anything below that I get crashes and reboots during Orthos or OCCT testing, similar to undervolting. The specs I have listed below are for an E8500 E0. The comp is stable now with lowered volatges then what I had just a few posts before. I continue to change my NB GTL's and my CPU GTL's in search of the perfect setting, for the most part I am learning how this CPU reacts to change although I must admit I still don't fully understand why it does what it does sometimes.

AI Overclock tuner: Manual
CPU Ratio Setting: 8.5
FSB Strap to North Bridge: AUTO
FSB Frequency: 533
PCI-E Frequency: 100
DRAM Frequency: 1068
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: Manual

1st Information :

CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 15
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time: Auto
Write Recovery Time: AUTO
Read to Precharge Time: AUTO

2nd Information :

READ to WRITE Delay (S/D): AUTO
Write to Read Delay (S): AUTO
WRITE to READ Delay (D): AUTO
READ to READ Delay (S): AUTO
READ to READ Delay (D): AUTO
WRITE to WRITE Delay (S): AUTO
WRITE to WRITE Delay (D): AUTO

3rd Information :

WRITE to PRE Delay: AUTO
READ to PRE Delay: AUTO
PRE to PRE Delay: AUTO
ALL PRE to ACT Delay: AUTO
ALL PRE to REF Delay: AUTO
DRAM Static Read Control: AUTO
DRAM Read Training: AUTO
MEM. OC Charger: Enabled
AI Clock Twister: AUTO
AI Transaction Booster: Manual

Common Performance Level [10]

Pull-In of CHA PH1: DISABLED
Pull-In of CHA PH2: DISABLED
Pull-In of CHA PH3: DISABLED
Pull-In of CHA PH4: DISABLED
Pull-In of CHB PH1: DISABLED
Pull-In of CHB PH2: DISABLED
Pull-In of CHB PH3: DISABLED
Pull-In of CHB PH4: DISABLED

CPU Voltage: 1.38125V Bios / 1.368V Windows
CPU GTL Voltage Reference (0/2): Auto
CPU GTL Voltage Reference (1/3): .640 Changed again.
CPU PLL Voltage: 1.62 / Higher fsb requires higher PLL. This seems to work well.
FSB Termination Voltage: 1.36 / I would like to lower this, although how ???
DRAM Voltage: 1.98
NB Voltage: 1.36 / Been able to lower this somewhat, mainly I think due to the NB GTL I have currently setup.
NB GTL Reference: .585 / Lowered again.
SBridge Voltage: Auto
PCIE SATA Voltage: Auto

Load Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : Auto
NB Clock Skew : Auto
CPU Margin Enhancement: Enhanced
03-04-2009, 11:10 AM
Mikefra2008

It(She) is good this bios =? 185 I have problems with the temp of the proce q9550
03-04-2009, 11:22 AM
x3mgamer

Quote:

Originally Posted by nigelke

Sow the vcore is lower. And is it stable?

nopers, it was bsod'ing like theres no tomorrow, these r my current stable settings, an occasional bsod happens now and then but its a lot better since ive installed newer chipset drivers

AI Overclock tuner: Manual
CPU Ratio Setting: 8.5
FSB Strap to North Bridge: Auto
FSB Frequency: 425
PCI-E Frequency: 100
DRAM Frequency: DDR2-1066
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: manual

1st Information : 5-5-5-15-3-55-6-3

CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 15
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time: 55
Write Recovery Time: AUTO
Read to Precharge Time: AUTO

2nd Information : 7-3-5-4-5-4-7

READ to WRITE Delay (S/D): AUTO
Write to Read Delay (S): AUTO
WRITE to READ Delay (D): AUTO
READ to READ Delay (S): AUTO
READ to READ Delay (D): AUTO
WRITE to WRITE Delay (S): AUTO
WRITE to WRITE Delay (D): AUTO

3rd Information : 14-5-1-6-6

WRITE to PRE Delay: AUTO
READ to PRE Delay: AUTO
PRE to PRE Delay: AUTO
ALL PRE to ACT Delay: AUTO
ALL PRE to REF Delay: AUTO
DRAM Static Read Control: Disabled
DRAM Read Training: AUTO
MEM. OC Charger: AUTO
AI Clock Twister: AUTO
AI Transaction Booster: Auto

C/P: A1 A2 A3 A4 | B1 B2 B3 B4
LVL: 10 10 10 10 | 10 10 10 10

CPU Voltage: 1.19375
CPU GTL Voltage Reference (0/2): 0,670
CPU GTL Voltage Reference (1/3): 0,670
CPU PLL Voltage: 1.54
FSB Termination Voltage: 1.24
DRAM Voltage: 2.02
NB Voltage: 1.26
NB GTL Reference: AUTO
SBridge Voltage: 1.1
PCIE SATA Voltage: 1.5

Load Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : Auto
NB Clock Skew : Auto
CPU Margin Enhancement: PERFORMANCE

Advance CPU Settings
CPU Ratio Setting: 8.5
C1E Suppport: Disabled
Max CPUID Value Limit: Disabled
Intel® Virtualization Tech: Disabled
CPU TM Function: Disabled
Execute Disable Bit: Enabled
03-04-2009, 12:59 PM
Leeghoofd

Quote:

Originally Posted by vrdublu

Hey LEEGHOOFD just curious if you have any suggestions on how I could lower my CPU VTT currently sitting @ 1.36V.

you are at 4.5Ghz, if you try at 8 multi I'm pretty sure you can pull of 1.26FSB Term or such... high FSB speed and total CPU speed need higher FSB term voltages. But I see people at 4ghz with 450FSB that copy your template which is totally unnecassary to apply as much volts....

For 600FSB Tests I didn't even need 1.36FSB term at 4.2Ghz... it all depends on CPU, mobo etc... I never needed above 1.3FSB term, 1.3NB Voltage for all my dual cores and PLL voltage had zero influence on my CPU's OC's

Maybe if you Disable Static Read Control and put in TFC 55 you could lower NB voltage a bit more and almost loose zilch to nothing in ram performance
03-04-2009, 01:14 PM
Mikefra2008

x3mgamer is stable 24/7 you Oc?
03-04-2009, 01:59 PM
oggie

Hi peeps

Got my pc watercooled so would like to finally OC my pc to higher speeds. Have had it OC at 4.0GHz by just changing FSB to 400 and its been stable from day one.
I have E8600 batch Q822A566 which i heard is meant to be quite a good batch.
Have tried overclocking a bit higher by just changing FSB and putting in CPU V to manual and got as high as this
http://i552.photobucket.com/albums/jj339/oggiet/42.jpg

I ran Intelburn and it passed but next day I booted up pc and got blue screen.
Just need some advice which setting need to be played with as there are soo many :)

ASUS P5Q DLX Template :

JumperFree Configuration Settings
AI Overclock tuner: Manual
CPU Ratio Setting: AUTO
FSB Strap to North Bridge: Auto
FSB Frequency: 400
PCI-E Frequency: AUTO
DRAM Frequency: 1066
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: AUTO

1st Information :

CAS# Latency: AUTO
DRAM RAS# to CAS# Delay: AUTO
DRAM RAS# Precharge: AUTO
DRAM RAS# Activate to Precharge: AUTO
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time: AUTO
Write Recovery Time: AUTO
Read to Precharge Time: AUTO

2nd Information :

READ to WRITE Delay (S/D): AUTO
Write to Read Delay (S): AUTO
WRITE to READ Delay (D): AUTO
READ to READ Delay (S): AUTO
READ to READ Delay (D): AUTO
WRITE to WRITE Delay (S): AUTO
WRITE to WRITE Delay (D): AUTO

3rd Information :

WRITE to PRE Delay: AUTO
READ to PRE Delay: AUTO
PRE to PRE Delay: AUTO
ALL PRE to ACT Delay: AUTO
ALL PRE to REF Delay: AUTO
DRAM Static Read Control: Disabled
DRAM Read Training: AUTO
MEM. OC Charger: AUTO
AI Clock Twister: AUTO
AI Transaction Booster: AUTO
Common Performance Level [5]
Pull-In of CHA PH1: DISABLED
Pull-In of CHA PH2: DISABLED
Pull-In of CHA PH3: DISABLED
Pull-In of CHA PH4: DISABLED
Pull-In of CHB PH1: DISABLED
Pull-In of CHB PH2: DISABLED
Pull-In of CHB PH3: DISABLED
Pull-In of CHB PH4: DISABLED

CPU Voltage: AUTO
CPU GTL Voltage Reference (0/2): AUTO
CPU GTL Voltage Reference (1/3): AUTO
CPU PLL Voltage: AUTO
FSB Termination Voltage: AUTO
DRAM Voltage: 2.1 V
NB Voltage: 1.3 V
NB GTL Reference: AUTO
SBridge Voltage: AUTO
PCIE SATA Voltage: AUTO

Load Line Calibration: AUTO
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : Normal
NB Clock Skew : Normal

Advance CPU Settings
CPU Ratio Setting: Manual
CPU VID: Default
C1E Suppport: Disabled
Max CPUID Value Limit: Disabled
Intel® Virtualization Tech: Disabled
Vanderpool Technology: Disabled
CPU TM Function: Disabled
Execute Disable Bit: Disabled
03-04-2009, 02:01 PM
vrdublu

Quote:

Originally Posted by Leeghoofd

you are at 4.5Ghz, if you try at 8 multi I'm pretty sure you can pull of 1.26FSB Term or such... high FSB speed and total CPU speed need higher FSB term voltages. But I see people at 4ghz with 450FSB that copy your template which is totally unnecassary to apply as much volts....

For 600FSB Tests I didn't even need 1.36FSB term at 4.2Ghz... it all depends on CPU, mobo etc... I never needed above 1.3FSB term, 1.3NB Voltage for all my dual cores and PLL voltage had zero influence on my CPU's OC's

Maybe if you Disable Static Read Control and put in TFC 55 you could lower NB voltage a bit more and almost loose zilch to nothing in ram performance

Thanks Mate I'll give'er a try and get back with some results.
03-04-2009, 05:05 PM
lesstutrey

Once i roll my BIOS back to 1403m tonight, what are recommended voltages for a q6600 going for a <4ghz bench run. VID is 1.25, so obviously i'll figure out vcore on my own, or just give it a ton of voltage cause i've yet to see it go over 65c with my 4160mhz clock. Upgrading to 1611 and 1702 was a mistake, that i'm paying for with having to afudos the thing back to 1403, since i haven't hit 4.1ghz since. And what should i disable/enable when it comes to things like static read, mem oc charger, dram read training. I always disable all the C1E, Speedstep stuff. Just a tad unsure about these aspects, as well as the voltages for vfsb, nb, & sb, cpu pll (all still stock cooled except for the watercooled CPU). Any help would be appreciated. Putting the rig into my sig right after this. It's all stock cooled but it's in a room that's about 10c. If the sig doesn't show up, it looks like this: CASE: TT Kandalf PSU: Corsair HX1000 MB: P5Q Deluxe CPU: Q6600/e8400 HDD: 2xWD 640gb raid1 3x Patriot Warp 32gb SSDs raid0 RAM: 4gb OCZ Reaper 1066 GPU: EVGA 8800gt SC H20: BIX240 XFLOW+GTZ+Petras DDC
03-04-2009, 08:27 PM
Mikefra2008

undestend =?=??=? made funk
03-04-2009, 11:13 PM
Leeghoofd

Quote:

Originally Posted by oggie

Hi peeps

Got my pc watercooled so would like to finally OC my pc to higher speeds. Have had it OC at 4.0GHz by just changing FSB to 400 and its been stable from day one.
I have E8600 batch Q822A566 which i heard is meant to be quite a good batch.

JumperFree Configuration Settings
AI Overclock tuner: Manual
CPU Ratio Setting: AUTO
FSB Strap to North Bridge: Auto
FSB Frequency: 400
PCI-E Frequency: 100
DRAM Frequency: 1066
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: AUTO

1st Information :

CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 15
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time: 55
Write Recovery Time: AUTO
Read to Precharge Time: AUTO

2nd Information :

READ to WRITE Delay (S/D): AUTO
Write to Read Delay (S): AUTO
WRITE to READ Delay (D): AUTO
READ to READ Delay (S): AUTO
READ to READ Delay (D): AUTO
WRITE to WRITE Delay (S): AUTO
WRITE to WRITE Delay (D): AUTO

3rd Information :

WRITE to PRE Delay: AUTO
READ to PRE Delay: AUTO
PRE to PRE Delay: AUTO
ALL PRE to ACT Delay: AUTO
ALL PRE to REF Delay: AUTO
DRAM Static Read Control: Disabled
DRAM Read Training: AUTO
MEM. OC Charger: AUTO
AI Clock Twister: AUTO
AI Transaction Booster: AUTO
Common Performance Level [5]

CPU Voltage: 1.3
CPU GTL Voltage Reference (0/2): AUTO
CPU GTL Voltage Reference (1/3): AUTO
CPU PLL Voltage: 1.56
FSB Termination Voltage: 1.26
DRAM Voltage: 2.1 V (try a bit lower here eg 2.02 )
NB Voltage: 1.3 V (try a bit lower here eg 1.26
NB GTL Reference: AUTO
SBridge Voltage: AUTO
PCIE SATA Voltage: AUTO

Load Line Calibration: AUTO
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : AUTO
NB Clock Skew : AUTO

Advance CPU Settings
CPU Ratio Setting: Manual
CPU VID: Default
C1E Suppport: Disabled
Max CPUID Value Limit: Disabled
Intel® Virtualization Tech: Disabled
Vanderpool Technology: Disabled
CPU TM Function: Disabled
Execute Disable Bit: Disabled

Get of them auto voltages plz, try the above. If not stable play with the FSB term voltage eg 1.3. if not stable try lower eg 1.22. Remember more voltages isn't always better !

Quote:

Originally Posted by lesstutrey

Once i roll my BIOS back to 1403m tonight, what are recommended voltages for a q6600 going for a <4ghz bench run. VID is 1.25,[/I]

For a quick bench run at eg 450FSB I would give them auto voltages a go. Even though they give too much, but for some quick runs it shouldn't do any harm. Depending on the run you want to make (superpi, AM3,...) you might need to tweak the rams to get optimal performance. But you better figure that out before pushing the CPU. Try with ya wanted FSB to get the best ram performance eg 450FSB : 1080Mhz with a PL of 8-9... see which settings you need then to get max ram performance and lowest latency.

Quote:

Originally Posted by Mikefra2008

undestend =?=??=? made funk

Grab another translator mate, hardly anyone understands a word you type
03-05-2009, 01:43 AM
Lewis23

Any advice/help for me?

Posted on page 217...
http://www.xtremesystems.org/Forums/...postcount=5424

Tnx:up:
03-05-2009, 06:57 AM
x3mgamer

Quote:

Originally Posted by Mikefra2008

x3mgamer is stable 24/7 you Oc?

yeah man, stable 24/7 at this oc :up:
03-05-2009, 08:35 AM
nigelke

Quote:

Originally Posted by x3mgamer

nopers, it was bsod'ing like theres no tomorrow, these r my current stable settings, an occasional bsod happens now and then but its a lot better since ive installed newer chipset drivers

AI Overclock tuner: Manual
CPU Ratio Setting: 8.5
FSB Strap to North Bridge: Auto
FSB Frequency: 425
PCI-E Frequency: 100
DRAM Frequency: DDR2-1066
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: manual

1st Information : 5-5-5-15-3-55-6-3

CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 15
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time: 55
Write Recovery Time: AUTO
Read to Precharge Time: AUTO

2nd Information : 7-3-5-4-5-4-7

READ to WRITE Delay (S/D): AUTO
Write to Read Delay (S): AUTO
WRITE to READ Delay (D): AUTO
READ to READ Delay (S): AUTO
READ to READ Delay (D): AUTO
WRITE to WRITE Delay (S): AUTO
WRITE to WRITE Delay (D): AUTO

3rd Information : 14-5-1-6-6

WRITE to PRE Delay: AUTO
READ to PRE Delay: AUTO
PRE to PRE Delay: AUTO
ALL PRE to ACT Delay: AUTO
ALL PRE to REF Delay: AUTO
DRAM Static Read Control: Disabled
DRAM Read Training: AUTO
MEM. OC Charger: AUTO
AI Clock Twister: AUTO
AI Transaction Booster: Auto

C/P: A1 A2 A3 A4 | B1 B2 B3 B4
LVL: 10 10 10 10 | 10 10 10 10

CPU Voltage: 1.19375
CPU GTL Voltage Reference (0/2): 0,670
CPU GTL Voltage Reference (1/3): 0,670
CPU PLL Voltage: 1.54
FSB Termination Voltage: 1.24
DRAM Voltage: 2.02
NB Voltage: 1.26
NB GTL Reference: AUTO
SBridge Voltage: 1.1
PCIE SATA Voltage: 1.5

Load Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : Auto
NB Clock Skew : Auto
CPU Margin Enhancement: PERFORMANCE

Advance CPU Settings
CPU Ratio Setting: 8.5
C1E Suppport: Disabled
Max CPUID Value Limit: Disabled
Intel® Virtualization Tech: Disabled
CPU TM Function: Disabled
Execute Disable Bit: Enabled

hmm than i shall stay with the old one :)
03-05-2009, 10:40 AM
Mikefra2008

It(She) is good this bios =? 1805 I have problems with the temp of the proce q9550
03-05-2009, 11:03 AM
Leeghoofd

What temp problems Mikefra2008 ? insane high temps ? post a screnshot of ya problem, will tell more than a thousand words
03-05-2009, 01:31 PM
vrdublu

Quote:

Originally Posted by Leeghoofd

you are at 4.5Ghz, if you try at 8 multi I'm pretty sure you can pull of 1.26FSB Term or such... high FSB speed and total CPU speed need higher FSB term voltages. But I see people at 4ghz with 450FSB that copy your template which is totally unnecassary to apply as much volts....

For 600FSB Tests I didn't even need 1.36FSB term at 4.2Ghz... it all depends on CPU, mobo etc... I never needed above 1.3FSB term, 1.3NB Voltage for all my dual cores and PLL voltage had zero influence on my CPU's OC's

Maybe if you Disable Static Read Control and put in TFC 55 you could lower NB voltage a bit more and almost loose zilch to nothing in ram performance

Well it seems as though my original settings seem to be right on par with what I'm getting now. At 1.26-1.30 NBv I can't even boot @ 550FSB, 1.32-1.34 tells me my Express gate intallation is bad and I need to resinstall it:shrug:, 1.36-1.38 I ran from .520-.645 with mixed reviews, but nothing stable, over .670 no boot. 1.40 seems to yield great success so far at a GTL of .590-.595 the latter being stable for 6 hours mem test. Next is to get into windows with stable NB and Memory and get the cpu stable at lower FSb VTT and VID. I don't know why I need such high Voltage but it seems it needs it to stay stable. Any other suggestions are more then welcome.:shocked:
03-05-2009, 03:48 PM
Martin.v.r

:eek:

http://www.xtremesystems.org/forums/...postcount=1396
03-05-2009, 08:29 PM
Mikefra2008

program OCCT the nigth is 68 65 60 58 not is hard? temp in Chile is 25grados ambient

(ventilacion Big tyfhoon and Q9550 C1
03-06-2009, 12:02 AM
Martin.v.r

E8XXX is NB 1.28/ 1,38v fine but Q cpu ned more 1.5/1.56v
03-06-2009, 03:45 AM
genish

I have a pb with the new bios the T° of cpu and nB are some time crazy

sometimes more 100° c for the cpu during 6 secondes while all the 4 cores under 64°
03-06-2009, 04:03 AM
Leeghoofd

Doesn the new bios have NB readout ? don't think so mate... better flash back to an older version
03-06-2009, 09:00 AM
Mikefra2008

JumperFree Configuration Settings
AI Overclock tuner: Manual
CPU Ratio Setting: 8.5
FSB Strap to North Bridge: 400
FSB Frequency: 414
PCI-E Frequency: 101
DRAM Frequency: 1100
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: AUTO

1st Information :

CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 15
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time: AUTO
Write Recovery Time: AUTO
Read to Precharge Time: AUTO

2nd Information :

READ to WRITE Delay (S/D): AUTO
Write to Read Delay (S): AUTO
WRITE to READ Delay (D): AUTO
READ to READ Delay (S): AUTO
READ to READ Delay (D): AUTO
WRITE to WRITE Delay (S): AUTO
WRITE to WRITE Delay (D): AUTO

3rd Information :

WRITE to PRE Delay: AUTO
READ to PRE Delay: AUTO
PRE to PRE Delay: AUTO
ALL PRE to ACT Delay: AUTO
ALL PRE to REF Delay: AUTO
DRAM Static Read Control: Disabled
DRAM Read Training: AUTO
MEM. OC Charger: enable
AI Clock Twister: lighting
AI Transaction Booster: AUTO
Common Performance Level [5]
Pull-In of CHA PH1: DISABLED
Pull-In of CHA PH2: DISABLED
Pull-In of CHA PH3: DISABLED
Pull-In of CHA PH4: DISABLED
Pull-In of CHB PH1: DISABLED
Pull-In of CHB PH2: DISABLED
Pull-In of CHB PH3: DISABLED
Pull-In of CHB PH4: DISABLED

CPU Voltage: AUTO
CPU GTL Voltage Reference (0/2): 0.635
CPU GTL Voltage Reference (1/3): 0.670
CPU PLL Voltage: 154
FSB Termination Voltage: 128
DRAM Voltage: 2.15 V
NB Voltage: 1.26 V
NB GTL Reference: 0.635
SBridge Voltage: 1.20
PCIE SATA Voltage: 1,50

Load Line Calibration: AUTO
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : Normal
NB Clock Skew : Normal

Advance CPU Settings
CPU Ratio Setting: Manual
CPU VID: Default
C1E Suppport: Disabled
Max CPUID Value Limit: Disabled
Intel® Virtualization Tech: Disabled
Vanderpool Technology: Disabled
CPU TM Function: Disabled
Execute Disable Bit: Disabled

Bios 1704 24/7 STABLE bios 1805 not stable ?¡?¡ occt 72grados ambient 31 santiago chile very hard?¡ o not?
03-06-2009, 11:00 AM
oggie

Ok git mine stable but can get it at 4.2GHz, tried following settings and all it did was corrupt my startup files so had to reinstall vista. My bios version is 1201...should u flash this to higher version :confused:

JumperFree Configuration Settings
AI Overclock tuner: Manual
CPU Ratio Setting: AUTO
FSB Strap to North Bridge: Auto
FSB Frequency: 420
PCI-E Frequency: 100
DRAM Frequency: Auto
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: AUTO

1st Information :

CAS# Latency: Auto
DRAM RAS# to CAS# Delay: Auto
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: Auto
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time: Auto
Write Recovery Time: AUTO
Read to Precharge Time: AUTO

2nd Information :

READ to WRITE Delay (S/D): AUTO
Write to Read Delay (S): AUTO
WRITE to READ Delay (D): AUTO
READ to READ Delay (S): AUTO
READ to READ Delay (D): AUTO
WRITE to WRITE Delay (S): AUTO
WRITE to WRITE Delay (D): AUTO

3rd Information :

WRITE to PRE Delay: AUTO
READ to PRE Delay: AUTO
PRE to PRE Delay: AUTO
ALL PRE to ACT Delay: AUTO
ALL PRE to REF Delay: AUTO
DRAM Static Read Control: Disabled
DRAM Read Training: AUTO
MEM. OC Charger: AUTO
AI Clock Twister: AUTO
AI Transaction Booster: AUTO
Common Performance Level [5]

CPU Voltage: 1.3
CPU GTL Voltage Reference (0/2): AUTO
CPU GTL Voltage Reference (1/3): AUTO
CPU PLL Voltage: 1.56
FSB Termination Voltage: 1.26
DRAM Voltage: 2.1 V
NB Voltage: 1.3 V
NB GTL Reference: AUTO
SBridge Voltage: AUTO
PCIE SATA Voltage: AUTO

Load Line Calibration: AUTO
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : AUTO
NB Clock Skew : AUTO

Advance CPU Settings
CPU Ratio Setting: Manual
CPU VID: Default
C1E Suppport: Disabled
Max CPUID Value Limit: Disabled
Intel® Virtualization Tech: Disabled
Vanderpool Technology: Disabled
CPU TM Function: Disabled
Execute Disable Bit: Disabled

The reason i have my RAM on auto is cause i just want to get cpu stable then will move onto RAM
03-06-2009, 12:51 PM
Leeghoofd

Flash to 1406 Oggie and up the Vcore to 1.35 and see if she get's into Vista then... later on you can still lower vcore if possible

Show 100 post(s) from this thread on one page