**Official DFI LanParty UT P35-T2R Review/Overclock/Guide Thread**

Priming 512k- 4096k FFT 1024 passed on 896 as of now 1254Ram/511x8Cpu, green slots occupied aggressive clock crossing and Trfc 58...Pl 13 pulled into 12.....
Write to Pre 15...8555aa turned to 8665aa
Gonna do 8k FFt later but so far much better no insta-reboot yet:up:
Thanks again Zsamz

@tootall Your setup looks sweet how is your 24/7 coming along?


@Zsamz what is the range of Trfc for memory frequency?

*Update 8k passed,used SetFSB to get 533:up: no other changes and blend priming at 1024 ...rounding error for 1024k on first thread 5 minutes in... trying 8k currently

@tootall Your setup looks sweet how is your 24/7 coming along?

It appears that my sweet spot is 450FSB. I can get it to boot up at up to about 465FSB but it takes some more voltage and is not rock solid stable. At 450 I am at 1.275 VID, 1.41 NB, 1.15 VTT, and 2.15 DRAM. SG and Everest v5.3 match voltages nicely. Under load shows 1.30 VID, 1.39 NB, 1.15 VTT, and 2.1 DRAM. This is with my E8400 and 1200MHz PI. It is very stable here. 10 passes of LinPack and Prime95 24 hours of blend. Everest shows read at about 9860MB/s and latency at 50.5ns. I am very happy with my voltages. Memory at 1125MHz using 5:4. Timings are fast, fast, 5-5-5-15-48 and pl6. Will not work at pl5. Trying to see what I can do to tighten timings but mostly won't boot. Actually, I am quite happy with this.

I also have the LT version which I just burned up. Basically a new build running at mostly stock. It hung while on and then would not POST, period. Jacked around with it for hours, no joy. I was never happy with the NB and PWM temps on this one. The UT with the heat pipes is definitely the way to go. I had a Xigmatec cooler on the NB which helped. I also used AS5 on the PWM to see if that would help. I finally determined that the layer of AS5 I put on the 8 PWM chips was too thin. Chips 1 and 8 showed no contact with the sink. This is basically irregardless of how hard I press on the sink. Just goes to show how useless the push pins really are. IMO they do not impart enough pressure. I am still trying to figure out what aspect of this is not flat enough and what I am going to do with the board.

When I want to update BIOS I get this like this(I'm using Logan/TMod CD):
http://img202.imageshack.us/img202/1...2009274.th.jpg

Also when I'm updateing BIOS with disk 1,44 I'm geting message that BIOS doesn't match and I have to use /nbl option. What's wrong with this MoBo :mad:

man i miss my P35...

sorry guys,is there any latest bios for super pi 32m to download for this ut p35?tq

im still rocking hard 24/7 with my lt p35. thanks to everyone on this thread for helping me out. this mobo is just awesome and the guys here incredible. thanks to all. if any require some help i can share my bios setttings for you. just hit me up. keep this thread alive!!!!!

^ Yes! I've been 24/7/365 with my UT P35 for about two years now!

What are you using for cooling your PWM, the stock cooler? You're really just running on air and getting a 3.7 overclock? Which DIMMS do you have? I got mine to boot at 3.8 but 3.0 has been my 24/7 speed on air.

I just started ordering waterblocks for mine!

What bios is good for a Q9550 E0? What are the ideal settings for performance with this processor?

Quote:

---

Originally Posted by elmysterio

What bios is good for a Q9550 E0? What are the ideal settings for performance with this processor?

---

i'm gonna play with p35 soon
but you need gigabut p45 for that cpu if you cant hit 4.0

Quote:

---

Originally Posted by zsamz_

i'm gonna play with p35 soon
but you need gigabut p45 for that cpu if you cant hit 4.0

---

I already have the motherboard and do not want to change it as it would mean to change all the platform and cost at least 1000 E. I just want to make a good quad. Currently I have an E6850 processor very good but I want to change it.

Well looks like us overclockers just know a thing or two about motherboards

Living Proof that they never die

http://i161.photobucket.com/albums/t.../Image0143.jpg

http://i161.photobucket.com/albums/t.../Image0142.jpg

http://i161.photobucket.com/albums/t.../Image0141.jpg

Thanks Soooooo much for your advice it worked...

There she is in full bloom again

Quote:

---

Originally Posted by zsamz_

i'm gonna play with p35 soon

---

So am i zsamz, only this time round i'm going to hit it with a kick ass SS that i'm in the process of building :) My E8600 hasn't been doing much on the UT P35 for some time, so it's going to get a very sharp wake up call in the not to distant future :D

glad it worked out
now show us what she can do

the ut p35 ranks #2 in my book right after the rampage extreme
but in ddr2 nothin beats it
even if gigabut p45 can clock ram higher but not faster;)

Quote:

---

Originally Posted by DoObs

Well looks like us overclockers just know a thing or two about motherboards

Living Proof that they never die


Thanks Soooooo much for your advice it worked...

There she is in full bloom again

---

Good to see this board back up here with all the others...still one of the best performing boards out there...

Zsamz...thanks so much for your help once again :D

Will get clockin sooon...this friday night weekend

What bios for DFI UT P35 t2r is good with a e6850 and what settings are best for performance in frequency: 3600mhz-3800mhz and 4000mhz with e6850? And for lower CPU voltage should be played with GTL ?

Quote:

---

Originally Posted by elmysterio

What bios for DFI UT P35 t2r is good with a e6850 and what settings are best for performance in frequency: 3600mhz-3800mhz and 4000mhz with e6850? And for lower CPU voltage should be played with GTL ?

---

i had my e6850 @ 500x8 +-1.42v 333/800 divider:up:

Quote:

---

Originally Posted by zsamz_

i had my e6850 @ 500x8 +-1.42v 333/800 divider:up:

---

What bios ? GTL voltage tweaks ? At the same voltage for my CPU 8x500fsb:D, depends on motherboard. Fpo-batch cpu ?

Quote:

---

Originally Posted by elmysterio

What bios ? GTL voltage tweaks ? At the same voltage for my CPU 8x500fsb:D, depends on motherboard. Fpo-batch cpu ?

---

:rofl: i dont know or remember
i havent touchen em in over a year

My processor is best but I want to take good memory 2x2gb

I had to choose between these memory kits:
G. SKILL F2-9600CL5D-4GBPI
or
OCZ PC2-8500 Low-Voltage Series Blade OCZ2B1066LV4GK
or
OCZ PC2-9600 Low-Voltage Series Blade OCZ2B1200LV4GK

I have a problem with the motherboard temperature (nb, pwm `48-50 full load),to change thermal paste on NB, SB and MOSFET or put another cooling them?

Quote:

---

Originally Posted by elmysterio

I have a problem with the motherboard temperature (nb, pwm `48-50 full load),to change thermal paste on NB, SB and MOSFET or put another cooling them?

---

I'm using Swiftech MCW30, temperatures about 40-45C. However actualy it's dismounted because of my GFX goes to RMA and I had to remove WC :/

On AC temp is 49C in Idle, (no OC). PWN temperature is the same.

My mobo is LT :)

Quote:

---

Originally Posted by tom256

I'm using Swiftech MCW30, temperatures about 40-45C. However actualy it's dismounted because of my GFX goes to RMA and I had to remove WC :/

On AC temp is 49C in Idle, (no OC). PWN temperature is the same.

My mobo is LT :)

---

I changed the thermal paste with MX-3 and is 48-50C on full load `OC to 3600mhz and the` 40-44C idle. The first time I open my computer temperature is 30-33C , after a few minutes increase to 40-44C. I think the temperature is high

Anyone tried tu upgrade BIOS with LANPARTY UT P45-T2RS one? Is It possible? I know that people update BIOS for DFI LP X38 with DFI LP X48 one.