Printable View
Just got an E0 E8500 with 1.175 VID. So far seems to do 4.6ghz 1.408V.....temps are really high on this one though (78C under watercooling). Shame as this seems like a really good chip, with some proper LN2 or osmething I think it could be very successful :)
yeh its weird gurusan some chips require very low volts at high clocks but once you apply over a certain voltage they get very hot i have a q822a435 and mine only needs 1.24 volts to run at 4.34ghz but once over about 1.375 volts it gets very hot, other chips need a much higher voltage to run at same clocks but run cooler even though they are taking more volts
Hey gurusan-Quote:
Originally Posted by gurusan
This is a little off topic but I was going to post my E8400 on this thread and I saw the overclock on this chip (E8600) and I thought you would find it interesting... high overclock :eek: with low volts and low temps. http://www.ocforums.com/showpost.php...0&postcount=45
Thanks for that, but 1.2125 is not really low VID....most are 1.25, some 1.225, others 1.2125.
1.175 is really quite low for an e8500 in my experience and it does run burning hot. At the same settings this chip is almost 20C hotter than my other 1.25 vid e8500
yep. my e8400 w/vid of 1.23 runs about 15c hoter than my e8500 w/vid of 1.25
I agree with you about it not being low VID... but that is still one of the best E0 chips (air cooled too) that I've seen.Quote:
Originally Posted by gurusan
hmm, just took a look at the clocks.
wow! that's pretty amazing. i almost don't believe it! 4.7ghz on those voltages........craziness I tell you! What stepping is it?
I was curious about that too. He posted a couple of weeks back and didn't mention fpo/batch#... I saw it last night. I'm going to post my new E8400 to that thread and I'll ask him. I'll PM the info to you if he responds.Quote:
Originally Posted by gurusan
thanks.
just tuned down voltage and put in 450fsb.....so far so good
http://img228.imageshack.us/img228/730/72715454tw3.png
got a replacement board for my P5Q-E, and its a rev 3 instead of rev 2, and lower temps with better OC:
http://i44.photobucket.com/albums/f3...ghze8400OC.jpg
What P45 revision is it using? It's listed on mainboard tab on cpuz.Quote:
Originally Posted by ssabripo
well if its a3 then hopefully it will clock like the new a3 UD3P's good luck mate
finally got 4400.it just took a little more vcore,and running1:1 http://i36.tinypic.com/ej75f4.jpg http://i33.tinypic.com/5oy3wl.jpg
rev A3Quote:
Originally Posted by JoeBar
what are the UD3P's clocking at? I think my bottleneck is my RAM... it's an older crucial ballistix PC6400, 4-4-4-12, but running it at 5-5-5-18 right now :confused:Quote:
Originally Posted by radaja
ok....running 13 min of orthos and counting! so far so good, so if it stays stable, I'm keeping this!! this A3 board rocks and so does the E0 Stepping e8400!!!!
http://i44.photobucket.com/albums/f3...ghze8400OC.jpg
@ssabripo,they are clocking very well,and clocking memory to world records
http://i161.photobucket.com/albums/t...l_018/8875.jpg
http://i161.photobucket.com/albums/t...0FSB12812s.jpg
Got this a while back....Motherboard is dead now though...:(
just got my 8500 in yesterday, what ive got so far..
http://img514.imageshack.us/img514/8135/41979292ld6.png
pushed alittle further...
http://img82.imageshack.us/img82/5456/26904517ze0.png
looks good.
played with my e8500 a bit more....aint a bad cpu :)
http://img529.imageshack.us/img529/4989/40502093qf1.png
where are you guys getting E0 E8500's from?
i get them fromt he bay
Batch: Q827A354
S-Spec: SLB9K
Here's my highest stable clock of 4.3 ghz.
http://i37.tinypic.com/e13hbc.jpg
This is my highest OC.
http://i38.tinypic.com/2qx3x1k.jpg
^5ghz, nice job by-tor :)
here's my update:
http://img407.imageshack.us/img407/9340/4500dm9.png