ASUS Maximus Formula SE

Quote:

---

Originally Posted by ReZ_

what bios are you running?

my temps warped from while changing versions.

---

Hi,

wrong post of Value.

NB: 55/54°C
SB: 54/50°C

this temps are while my ambient temp in case are 42°C. at moment i have deinstalled all casefans. (build a new enviroment)

now i have found in the X38 chipset information a bit about the thermal specification. highest working temperature are 85°C, but the MCH works up to 92°C without a failure. Reboot's are strictly needed under "catastrophal condition" (without hardware damage of MCH) at 105°C.

Quote:

---

Originally Posted by Cumulonimbus

now i have found in the X38 chipset information a bit about the thermal specification. highest working temperature are 85°C, but the MCH works up to 92°C without a failure. Reboot's are strictly needed under "catastrophal condition" (without hardware damage of MCH) at 115°C.

---

Die or IHS temperatures ? How is the temp measured by the board ? W/o knowing that the info is pretty much worthless..

Quote:

---

Originally Posted by Grendel66

Die or IHS temperatures ? How is the temp measured by the board ? W/o knowing that the info is pretty much worthless..

---

on the top in middle position of the IHS

Quote:

---

Originally Posted by Cumulonimbus

on the top in middle position of the IHS

---

Yes, found the specs here. That's most definately not where ASUS placed the NB temp sensor :P Does anyone know where it is ?

Quote:

---

Originally Posted by Grendel66

Yes, found the specs here. That's most definately not where ASUS placed the NB temp sensor :P Does anyone know where it is ?

---

hehe, ASUS cut the IHS, put his Sensor on the Die (with UHU) and put the IHS on the MCH again. Now, this is the reason how expansive the maximus is. :-)

Quote:

---

Originally Posted by Grnfinger

ummm its ctrl+print screen then paste in paint

---

Actually, it's ALT+PrtScrn.

Quote:

---

Originally Posted by devilhood

Yeah, I was talking about the CPU not the NB haha.

I just edited my post to make things a little bit more clear :p:

Alright, well I've ordered a heatsink lapping kit, so I will give that a try on monday.

---

Quote:

---

Originally Posted by Grnfinger

Just orderd a lapping kit myself, hope it will drop temps 5 degrees or so.
I made a few changes to my water loop, setup a push pull and that made a nice 3-5 degree drop in temps, I also added a Corsair ram cooler and I must say what a huge piece of :banana::banana::banana::banana: , you would think from Corsair it would be better quality. It's comming out today.

---

I ordered one as well about a week ago, expecting it this weekend. If one of you guys don't start a thread first I'll start one with detailed pics and tests. Are you guys lapping experts or is this your first?

Is OCCT buggy or not ( 1.1.0) after a day tweaking I decided to to disable everything (transaction booster/dram static) now it isnt even stable with all off and even downclocked to 1:1 ( 425 fsb) 850 5-5-5-15 , what the heck is going on. The ram was memtest86+ stable for 13-14 hours. I havent prime yet, but from my experience if it is memtest86+ stable it would be prime95 stable. and this ram was tested @ my P5K deluxe...... So am I good as long it is prime blend stable for say 12 hours+? It could be while testing during OCCT it corrupted my OS, maybe thats why it will error with any clocks? Because during tests I had a view times My whole screen went black or Pink or White...

Quote:

---

Originally Posted by mc2k

Is OCCT buggy or not ( 1.1.0) after a day tweaking I decided to to disable everything (transaction booster/dram static) now it isnt even stable with all off and even downclocked to 1:1 ( 425 fsb) 850 5-5-5-15 , what the heck is going on. The ram was memtest86+ stable for 13-14 hours. I havent prime yet, but from my experience if it is memtest86+ stable it would be prime95 stable. and this ram was tested @ my P5K deluxe...... So am I good as long it is prime blend stable for say 12 hours+? It could be while testing during OCCT it corrupted my OS, maybe thats why it will error with any clocks? Because during tests I had a view times My whole screen went black or Pink or White...

---

That's because Memtest86 is worthless....use OCCT, Prime blended, or HCI memtest....I posted a link on the previous page or two to HCI Memtest.

i have to know about the vid of the cpu is it good or bad to have lower.
and if there is way to know wich cpu better for oc?
i have vid-1.2875v q6600 and i cant go up to 4ghz(now i'm with 3900 1.6v 40c ide 74c load)

Quote:

---

Originally Posted by doronav02

i have to know about the vid of the cpu is it good or bad to have lower.
and if there is way to know wich cpu better for oc?
i have vid-1.2875v q6600 and i cant go up to 4ghz(now i'm with 3900 1.6v 40c ide 74c load)

---

Sounds like you've peaked with load temps like that. Most Q6600s I've seen don't go past 4GHz with your typical water cooling. I can get close to 4.1 but just idling. It's not stable.

Quote:

---

Originally Posted by doronav02

i have to know about the vid of the cpu is it good or bad to have lower.
and if there is way to know wich cpu better for oc?
i have vid-1.2875v q6600 and i cant go up to 4ghz(now i'm with 3900 1.6v 40c ide 74c load)

---

Why din't you use the CPU block that came with your cace. When I saw the size of it, I thaught yea this one is nice. My temps are as follows, With the case WC fan control on normal:

Core 0: 34c
Core 1: 35c
Core 2: 33c
Core 3: 34c

Quote:

---

Originally Posted by ElEctric_EyE

I ordered one as well about a week ago, expecting it this weekend. If one of you guys don't start a thread first I'll start one with detailed pics and tests. Are you guys lapping experts or is this your first?

---

First timer on lapping, I have been reading alot tho and it's dosent seem overly complicated.
I do alot of die grinding and polishing die's at work so this cant be much different.
I would however look forward to you starting a thread, tips pics and ect.. would be very helpful, I'm not looking for any new shiny paper wieghts;)

Quote:

---

Originally Posted by ElEctric_EyE

Sounds like you've peaked with load temps like that. Most Q6600s I've seen don't go past 4GHz with your typical water cooling. I can get close to 4.1 but just idling. It's not stable.

---

i was able to ide 4.2 but not stable.
i'm waiting for the next bios,maybe more mhz.
do you know about vid?lower better oc?

Quote:

---

Originally Posted by jorgito05

Why din't you use the CPU block that came with your cace. When I saw the size of it, I thaught yea this one is nice. My temps are as follows, With the case WC fan control on normal:

Core 0: 34c
Core 1: 35c
Core 2: 33c
Core 3: 34c

---

my case without the wc,yours looking nice.
i'l try dry ice or ln2,
by the way did you notice that with the profile you get stable and if you change it and return it's not the same you'l have to play again?

can i get 500+ with maximus ?
if so, i try vtt,nb,gtl and didnt go even 470+,i see (not here) with 100$ mb
goes 500+
thanks

for lapping anything i use a true flat thick piece of glass or metal (checked with a straight edge) then tape some wet dry auto paper on it and go to town. 500,1000,1500,2000. i make sure i keep it clean, no zippers, little granulars in the paper or under it. you will feel them if they are there. i use a straight edge on whatever i am lapping against light to check for flatness. if it has any highs or lows light will shine through..

Where is the intel hyperthreading option in the bios??

i remember seeing it in my bios, but now i can't find it! :rofl:

I'm having audio latency issues with reason 4.0, and i want to toy with HTT to see what it does

thanks

I have the following problem.Prime 95 Small FFt's im am rock stable.But when i run the Blend i always get an error at 47-48 min.And i mean no matter what bios settings i have (PLL volt-NB volt-RAM volt-SB Volt) i always get an error at exactly 47-48 min.Not 46 neither 49.Do u have any ideas what to pay attention at.I have run out of ideas :confused:

And by the way i have lowered the mem timings @ 5-5-5-15 an increased Ram volt at 2.1.Still nothing.

Hey ChaosAD, I got the same probleme like u......... but Mine is even worse Same RAM, I cant GET this ram at Any speed Prime passed/ OCCT passed within a hour...... it worked @ my P5K deluxe flawless, on the P5K it was stable 24/7 1167mhz 5-5-4-9 @ 2.05v and 1200mhz 5-5-5-12 @ 2.05v..... On the maximus I tried to get 1133 mhz @ 5-5-4-9 running disabled even all transaction/twister/dram ... still no go , upped the volts up to 2.21 actual... still cant pass...... and then I downclocked the mem to 850 mhz 5-5-5-15 @ 2.10 actual, still cant pass LOL, what the :banana::banana::banana::banana: is going on:X and eventually it corrupted my OS LOL.

however I just tested 14 hours memtest86+ no errors before I tried to run P95 Blend/OCCT, so the ram is not faulty, it seems that this board + my Ballistix doesnt like eachother :X , Tried bios: 0802/0903/0907 all the same. I think I am finally gonna swap tomorrow in My 2x2 G.Skills in and see how it works.

Quote:

---

Originally Posted by ChaosAD

I have the following problem.Prime 95 Small FFt's im am rock stable.But when i run the Blend i always get an error at 47-48 min.And i mean no matter what bios settings i have (PLL volt-NB volt-RAM volt-SB Volt) i always get an error at exactly 47-48 min.Not 46 neither 49.Do u have any ideas what to pay attention at.I have run out of ideas :confused:

And by the way i have lowered the mem timings @ 5-5-5-15 an increased Ram volt at 2.1.Still nothing.

---

I had the same problem. My Q6600 is Small FFT stable 3.6GHz@1.32v. BUT for blend I have to increase the voltage to 1.34v to get it stable and dont error at 47-48min into the test.

So I passed the memtest 760 percent coverage @ 1.55nb, 1.35cpu, 1.48fsbvtt, ddr2 @ 2.28v.. but try doing the blend test and am failing within 15 minutes now?

What is the problem? I am trying to mess with settings... it passed the blend test before with 1.47nb, 1.42fsbvtt, 1.35cpu ddr@2.28v but I needed to up the volts to pass the prime blend/geoforms at the same time because it would crash my cpu.

Also, I was wondering why a lot of people here with q6600 oc to 3.6ghz use much lower voltage than the anandtech review of the maximus. They recommended 1.61-1.7nb for anything past 440fsb, and 1.5-1.6fsbvtt for anything past 440fsb. Did they get it totally wrong or does the newer bios play a role? I can't seem to get my cpu stable enough to pass all tests. Always seems to pass 2 out of 3. (OCCT, Prime, Memtest)

Another thing, should I enable or disable CPU TM Function and Vanderpool Tech. in bios?

Anyone post some good settings for 3.4ghz, my room is hot so want it at 3.4 till i get more fans,

Please help using the step up to qx6850 @ 3ghz at the mo.

Check my sig for my system details. thanks

ok, you guys suffering from the ~47 minute crash in prime95 blend :
try running a custom test with whatever k size is not passing.

At some point, I was always crashing at prime95 blend at about 47min. Turns out the 896k test always failed. So I ran 896k tests only and upped my vcore until stable. I had to up it a few notches to pass :shrug:

there ya go :up:



Krav : what bios are you using?? I have stable settings at 3.4 on 0903 bios.

BTW, i'm still looking for that iNTEL HTT option in the BIOS.... does anyone have that in their BIOSes or am i HigH?