Printable View
Very strange I had a problem on my first Striker between 490x10 and 453x10. I have not seen any holes in the higher ranges on my new board and ran a SuperPi 1m last night at 4601 without issue. Ill play around and see if I can find some holes this weekend and then document my findings.
Not the greatest SuperPi in the world but not too far off the 975x mobos either...
http://thumbsnap.com/t/dFNQNBiw.jpg
what vdimm used for 450mhz 1T ?Quote:
Originally Posted by sdumper
too much... 2.4volts :( I have a fan blowing on it but it still makes me nervous.Quote:
Originally Posted by eva2000
I went to 2.5 for the 4.6 benches here:
http://thumbsnap.com/t/dFNQNBiw.jpg
trc = 12 and trfc = 18
And for normal use I use 2.25 to 2.3 ... depending on the timing (i used 2.3 for the orthos run just as a stability precation)
http://thumbsnap.com/t/GfWJfZpI.jpg
is that with team 6400c3 or gskill ? seems about same vdimm i need for gskill 6400 hz for 450mhz 1T
Team Xtreem: TXDD2048M800HC3DC
http://www.tankguys.biz/ddr2-3338-p-...60618fed6297ed
Note: I also have the G.Skill HZ but haven't tried them yet....
Likewise, I still haven't found my sweet spot yet so im still hopefully for a sub 10s superPi maybe at 4.65??
Are you running linked or unlinked? I am running => linked / synch mode.
I wonder If unlinked 1100/1200 5-5-5-15 2t would get me a faster time.
I just got my Evga 680i board today but I have some problems.
Bios won't boot upp with my settings, it loads default settings all the time.
2.66Ghz E6700
Any idea what can be wrong?
What are your settings?
Fsb (QDR) 1500 boots 1066.7
Mem 4-4-4-12 1T boots 4-4-4-11 1T
Vcore 1.675 boots 1.64v
Fsb 1.2v
Mem 2.2v
nForce SPP auto
nForce MCP auto
HT nForce SPP<->Mcp auto
Try changing to 2T.
Boost FSB voltage to 1.4
Found the problem I can't boot up with Fsb memory ratio on 1:1, I need to set iy on auto. Anyone know why I can't set it on any other value?
And is someone using Scythe Infinity on the board? Might as well ask what cpu coolers you are using are using.
Here is an 8x500 on the evga i680.
CPU-Z has errors opening the driver.
http://premium1.uploadit.org/skiman/bench/8x500.JPG
Here's something for you. I found that getting this fsb could only be done immediately after a bios clear/reset. Going right into 8x500 is no problem; however upon reboot POST CODE 11 happens, and into that OC Warning message.
i was using the infinity then went water as stuff were getting hot.. especially here where ambient temps are 32 to 36 degrees celcius..
@ gas try unlinked.. anyway i found the p23 bios extremely unstable for clocking.. sick of it.. went back to p21.. and got my 4ghz screen
530MHz FSB on EVGA 680i SLI (Vspp voltmodded to 1.66V) :banana:
http://valid.x86-secret.com/show_oc?id=151702
SuperPi1M @ 513 MHz:
http://img233.imageshack.us/img233/4...2duohi7.th.png
Just wondering why u guys lower the multiplier on the 6600's? is it just to get more FSB?, I think u actually waste some performance doing that on the 680IQuote:
Originally Posted by S_A_V
just a question ,dont flame me cause i kill u ok
btw this is my 680I 444x9 so far on air , going water this next week
hmm can u run the temps into the high 60s with no problems ?? im currently in the high 50s and that kinda worries me
Yes it worries me too, i only dhad it @ 4G for a few just to do the screenshot , Id like to keep it under 50 underload at that speed if i can, iam reading about watercooling at the moment so i can go water , i think my cpu need to be lapped too , one core temp is higher than the oter one, at least is better now after i applyed the artic silver , b4 that my temps were crazy with regular thermall paste (didnt have artic silver at that time) the diferents are very highQuote:
Originally Posted by jetjaguar
I lowered mine just to see if it could do a 500.Quote:
Originally Posted by Ajfina
Hey guys!
What is the HT multiplier setting?
It is set to 5X right now. Should I thouch this at any point when overclocking?
What about Linkboost?
mines at 3x
Maybe you can tell us how you did that ?Quote:
Originally Posted by S_A_V
What bios you use ?
What cooling ?
And what settings ?
i turn off linkboost when i go over 3.6 . right now im at 3.4 and linkboost is onQuote:
Originally Posted by orion23
Hi !!! got a friend that recently bought a 680i in concrete the Evga one. Problem lies on overclocking capabilities, once he set everything in BIOS and wants to save changes appears the message Checksum error.
Any thoughts on that, can some one tell me what to do to solve that .
thanks in advance!!!
I'm not sure FEEXX but I would try flashing the BIOS to the newest version? Even if he already flashed it recenlty I would do it again. It sounds like something probalby went wrong during a recent BIOS flash!
well, this afternoon i was testing a q6600 ES and was a complete failure, i dont know why i couldn't change de multiplier of the cpu in bios, well it changed but when booted doesn't change it, and i couldn't pass the 3.3ghz wall doesn't matter voltage increments. weird.
the 680i makes my q6600 and a e6600 failed in super pi, in all test, but they do past prime and other test, what do you think the problem could be.
i'm using p23 bios final. the MB is evga.
off topic but the Striker 0701 bios has vCore holes...
Testing different settings this weekend but have found 2 confirmed holes so far.