Printable View
it didnt help :( ive tried every bios from the stock to stilts.still this 6x multi.the only way i can change it is with crystal cpuid.any other options i may need to disable/enable?im at a total stand still.:brick:Quote:
Originally Posted by JWilson
which cpu are you using on this board?Quote:
Originally Posted by Maxfly
I have been trying to help him on Guru3d, but I lack the board so all of my suggestions are general, here is a post of his detailing what is wrong
Maxfly says.
ive tried everthing from the stock pt bios to the modded deluxe bios' that were posted at xs.i cant even run this thing at stock speeds with the 6x multi.it defaults to 1600mhz.ive tried all 3 mem dividers.the retarded thing is in the bios post screen it shows the 9x but in windows it drops to 6!im gonna send this thing back if i dont find the answer soon.that p5wdh in the openbox section of the egg is starting to look pretty damn good.this is the 3rd motherboard in 3 months thats gone crazy.im going nuts man!
nope ive only got the 6600
thx for the links.ive got those two and 3 others as well lol.i guess ill work my way back thru them and see what happens.
im really wondering if this mb isnt borked.it takes like 2 full minutes to load windows and like i said b4 it reboots after i change even the simplest bios option.like it would if you oced the fsb too far.even when i disabled the cpu options it reboots!grrrr
the other thing is my voltage...in cpuz its at .988-1.088 wtf???i can adjust it with crystal cpuid but no matter what i set it to in the bios it goes back down again.
sigh
i got it lol.blindows was corrupt.reinstalled and everything is fine now. :)
Cool!:D
Sorry I havent taken the time to prune through this whole thread but I'm fed up with my damn AW9D-MAX and looking for a new board. Will this board actually pull 500+fsb out of the box? If so then I think i've found myself my next board... (tired of waiting around for the RD600 and the IN9 32X-MAX)...
It can, but the GA-965P-S3 is better and has CPU multiplier control.
Is it possible to flash the PT board with the Deluxe bios?
Thanks
yes it works.
Albatron PXP965 also works with /F switch.....
Well I have D9 chips, and it doesnt work as it should:confused:Quote:
Originally Posted by loserkids
woohoo i gota c2 motherboard to. i hit 400 now on 914 mod bios still tweaking results very soon. board doesnt like super talent t6ua512c5 memory at all 325 highest lmao going back to newegg. put in corsair cm2x512-5400c4 and got 400fsb better result soon.
edit: heres a pic no test yet just goin for raw fsb:) . this is at 1.52 vcore. my nb volts r way off i set 1.45 in bios and come back in bios after reboot and its reading 1.65 at 1.45 lol. hardly any vdrop i set 1.50 and it stays right at 1.49-1.50 always. more results soon back to tweaking lol:) :) :) :)
http://img218.imageshack.us/my.php?image=400vp6.jpg
@MaxFly
Thanks for reply:)
Hi All,
I'm currently overclocking my 965PT MB. Default Bios.
My system is a D2D 6600 CPU running 1:1 on 300FSB.
All seem ok.All mobo setting at default for overclocking.
I can run PI 32MB no problem, aswell Prime95 on both CPU cores.
Temp when running Prime95 on both CPU cores 57 Deg. Celius.
When running Prime95 on single Core 46 Deg. Celsius.
I have been running Prime on both cores for 3.5 hours no problems.
Running Prime95 on single core for 7.5 hours no problems.
Running memtest86+ for 8 hours no problems.
The actual problem I have when running 3DMark05.
Some times it benches ok the next time not.
I'm using Windows XP64.
Any help would be welcome.
Is your gfx card overclocked too much?
Hi Gas
My XFX 7800GTX 256MB is not overclocked.
I'm running 3DMark05 version 1.0.0, I see their is a later version available.
I have seen in some forums that there are some issues with XP64.
I'm using Nvidia driver "93.71_forceware_winxp64_english_whql".
I also did run into the 6x multi problem.When I enable at bios level and XP64 level. At time it does not want to kick in at 9x multi. I then have to reboot XP64.
Then it is ok again.It could be MB related or XP64 issue, not shure.
well heres a lil update on my 965pt and e6300. highest nb volts i can run is 1.45v it will not boot with 1.55v tries everything. highest fsb was 480 then a restart my settings were:vcore 1.60v, vfsb 1.4v, nb 1.45v, vddr 2.2v. the memory is good to 530mhz 5-5-5-15 at 2.2v on ddr667 divider so i dont think thats holding me back. im using the 914 mod bios. could u guys give me ur bios setup that r hittin over 500+ fsb. stock bios was 914 and cpuz read tforce 965pt deluxe.thanks for all the help this thread is great:)
well i think the e6300 has a 480 fsb wall witch really sucks. no record trying with this one. i will buy a couple new e6300 soon to play with and will have better results then i hope. all settings messed with for hours and cant get over the 480fsb. 460fsb stable at low voltage and seem to be ok on the board. thanks again for all ur help everybody
Have you tried the 533 memory divider?
ya thats the main one i ran on. i have my p4 2.8ghz in it right now and hit 4.6ghz with 1.8vcore in bios but actually 1.76vcore in pc health.
4.6Gig/7x = 657FSBQuote:
Originally Posted by natedog420
That's super!
im wondering if anyone else is having issues with cold boots?if i power down and come back a hour later the pc boots to black screen.shuts off reboots itself but doesnt display.so i have to power down.flip the ps switch and hold the chassis power switch down for a few seconds.then turn the ps switch back on to boot up.its done this with 2 dif powersupplies.a enermax noisetaker 600 and a seasonic m12 700.any ideas?thx in advance :)
Yeah, this thing is a disaster to get running, cold boots, hot restarts, takes some serious coaxing to get going. But the funny part is, once you get it running, it is rock solid.
Must be female. :lol:
Quote:
Originally Posted by Maxfly
i agree 100%.once shes up and running its a friggin rock.just wish i could get rid of this annoying cold boot crap lol.
He ran it on a P4 2.8GHz, which has a higher multiplier;)Quote:
Originally Posted by JWilson