Mine 270Mhz 3-4-3-6 1T 2.6v pass Memtest86+ on Bios more than 8 times :p:
271Mhz no go, 10 errors on Test 5.
272Mhz no go, 40 errors on test 5.
Printable View
Mine 270Mhz 3-4-3-6 1T 2.6v pass Memtest86+ on Bios more than 8 times :p:
271Mhz no go, 10 errors on Test 5.
272Mhz no go, 40 errors on test 5.
so now i will try it with 2x80mm fans in front
of them :D
Lets hope :rolleyes:
yea, i love my UCCC because they require such low voltage for sweet performance. nice to see some regular results and not hand picked ones. they are always so misleading.
Relax it a bit and it should handle even more. How far it goes 3-4-4-8?Quote:
Originally Posted by Counter CS
what i want to know is how to get it to run 3-3-3-6. im stable @ 290 3-4-4-8.
Time to tweak my ocz sticks some more. right now thier at 275 3-4-4-8 2.6v, at around 277 they start to error, so im hopeing for 280. :D
Is it not normal that my sticks need 2.75~2.8V for a stable 32M run ??? They're GSkill HZ.
UCCC usually likes low volts, around 2.6-2.7.
OPB? what does MEM CLK 2 and MEM CLK 3 do exactly? Just wondering cause mine is enabled by default and yours is disabled.
I love my GSkill UCCC "0603" I am able to get 282 mhz out of them at 3-4-4-8 and 280 X 10 works great with my CPU/RAM at 1:1 :D
This is with NO TWEAKING with A64. Simply stock settings and timings.
http://www.strippoli.com/gskill282.JPG
http://www.strippoli.com/gskill280maxcpu.JPG
GSkill HZ, 0601, 260MHz MAX. later teamgroup I had was good to about 285
Quote:
Originally Posted by Delirious
mine does around 265 with 2.5v
mem clk 2 and 3 are dimm slots
0 and 1 are yellow slots and 3 and 4 are orange slots
they're disabled to get a slightly better superpi time (assuming you dont have ram in those slots)
barely noticeable though...maybe a couple seconds difference in 32mb superpi
Thnx for sharing your thought OPB....hope to test some UCCC again then
:)
Hello guys, I'm having HARD time stabilizing my Gskill HZ. They are 32M Stable, 2 hours of Prime95 Blend Test stable, [b]but not over 80% in memtest nor in memtest86, (2 errors per loop, sometimes 4).
What could it be? here's a screeny.
Im using 702-1 BIOS, 702-3 did not work for me.
http://balandra.uabcs.mx/aleman/extr...32M_stable.jpg
Yup. Actually A64tweaker reads in that way in DFI Expert/Venus, appear disabled by default. In Ultra-D/SLI-D/SLI-DR the four CLKs are enabled.Quote:
Originally Posted by chinkgai
Quote:
Originally Posted by corvus_corax
yeah, my sli-d used to have all four enabled by default...but recently only mem clk 1 is enabled while the other three are disabled!
only thing i can tell that i've changed is the bios, which ive flashed to a recent release (3/29/06)
guess the bios eff'ed things up?