Need help pushing Opteron 146 > 3Ghz

Printable View

Show 100 post(s) from this thread on one page

02-20-2006, 07:01 AM
kiwi

2 Attachment(s)

I just removed IHS off my opteron 146. Temps dropped from 50C load to 38C. I will post pics later because this time I cut my finger a bit and it is still bleeding :caution: :eek: :p:
Lol similar results were with all my venices without ihs but luckily I didnt cut finger then. I might reinstall IHS because it will only up temps a bit (comparing to naaked chip), at least that was the case with venice.

EDIT:
Pics as promised, notice that vcore is higher when IHS is off. Not the best chip but 3Ghz is ok at 1.65V with IHS or 1.6V without.

http://www.xtremesystems.org/forums/...1&d=1140449254

http://www.xtremesystems.org/forums/...1&d=1140449254
02-20-2006, 09:29 AM
b1tterman

goes better now but not very healthy without IHS:slobber:
02-20-2006, 12:35 PM
AP0ll0UK

Quote:

Originally Posted by kiwi

I just removed IHS off my opteron 146. Temps dropped from 50C load to 38C. I will post pics later because this time I cut my finger a bit and it is still bleeding :caution: :eek: :p:
Lol similar results were with all my venices without ihs but luckily I didnt cut finger then. I might reinstall IHS because it will only up temps a bit (comparing to naaked chip), at least that was the case with venice.

Your very brave I'll give you that. How did you find the removal of the heatsink and what did you use to get it off? Also, what cooler are you using?
02-20-2006, 02:17 PM
kiwi

Well, I would not take IHS off FX cpu :)
I am using razor made by Gillette :D I am also using rubber gloves to hold that razor. Cooler is either TT BT or custom watercooling.
02-20-2006, 02:27 PM
Big.Wayne

Great to see people showing stability screen shots, keep it up :)
02-20-2006, 02:28 PM
HARDCORECLOCKER

:D Well, after collecting some experience I'd rip it off from any CPU:

http://img377.imageshack.us/img377/5...w5220068lx.jpg

http://img355.imageshack.us/img355/8767/15527wn.jpg

:woot: :woot: :woot:

:toast:
02-20-2006, 03:22 PM
AP0ll0UK

Quote:

Originally Posted by kiwi

Well, I would not take IHS off FX cpu :)
I am using razor made by Gillette :D I am also using rubber gloves to hold that razor. Cooler is either TT BT or custom watercooling.

Were you wearing those rubber gloves when you sliced your finger open :D Was it the old Gillette Mach 3 Turbo that you had on the job? Cracking razors lol

Which cooler were you using from the screen shot of the awesome 3Ghz that you had it running at? Was it water of the TT BT?

Also, if your running it at 3Ghz at 1.65v, are you going to leave it at that or run it slightly slower at lower volts?

Quote:

Originally Posted by HARDCORECLOCKER

Well, after collecting some experience I'd rip it off from any CPU:

That looks like a neat job Hardcoreclocker and a nice speed and volts you've got your chip at but I notice you got the MachII on the job as well....lovely :D
02-20-2006, 03:26 PM
dinos22

Quote:

Originally Posted by AP0ll0UK

That looks like a neat job Hardcoreclocker and a nice speed and volts you've got your chip at but I notice you got the MachII on the job as well....lovely :D

i don't think that shot was with phase as the temps look too high for MachII....he's probably got it on water or air........my air idles at about 26-27C with 3.1GHz 1.63v
02-20-2006, 03:43 PM
HARDCORECLOCKER

:D Look any closer to my SIG - see the word "PREVIOUS".........

Promy sold long time ago - this is done on water (not chilled) and room temp of ~20°C.

:toast:
02-20-2006, 03:45 PM
dinos22

Quote:

Originally Posted by HARDCORECLOCKER

:D Look any closer to my SIG - see the word "PREVIOUS".........

Promy sold long time ago - this is done on water (not chilled) and room temp of ~20°C.

:toast:

heheheh kinda cold in that factory....do they crank the air con like that all the time or what :p: :D
02-20-2006, 03:52 PM
003

I have a 146 that does 3GHz ... at 1.675v
02-20-2006, 04:08 PM
HARDCORECLOCKER

Quote:

Originally Posted by 003

I have a 146 that does 3GHz ... at 1.675v

:D On air? Would be perfect for a bacon & eggs breakfast.........;)

@dinos22 :

:stick: We have W_I_N_T_E_R here in Europe................;)

:toast:
02-20-2006, 04:29 PM
dinos22

Quote:

Originally Posted by HARDCORECLOCKER

:D On air? Would be perfect for a bacon & eggs breakfast.........;)

@dinos22 :

:stick: We have W_I_N_T_E_R here in Europe................;)

:toast:

heheh i thought you were from AMD Factory literally heheheh....Penang Malaysia is the closest one to me :)
02-20-2006, 04:30 PM
003

Quote:

Originally Posted by HARDCORECLOCKER

:D On air? Would be perfect for a bacon & eggs breakfast.........;)

@dinos22 :

:stick: We have W_I_N_T_E_R here in Europe................;)

:toast:

Yep, on air. Of course I don't run it at that speed, but technically it IS stable. I keep it at 2.9GHz.
02-20-2006, 06:14 PM
AP0ll0UK

Quote:

Originally Posted by dinos22

i don't think that shot was with phase as the temps look too high for MachII....he's probably got it on water or air........my air idles at about 26-27C with 3.1GHz 1.63v

Which air cooler were you using for that dinos22? Also, did you see my reply to your post on page 1 after you mentioned keeping the 1/2 divider? What do you reckon?
02-20-2006, 06:19 PM
dinos22

Quote:

Originally Posted by AP0ll0UK

Which air cooler were you using for that dinos22? Also, did you see my reply to your post on page 1 after you mentioned keeping the 1/2 divider? What do you reckon?

Just read your post..........yeap dividers are funny buggers...sometimes they work and sometimes they don't especially odd ones like 150/183 that sort of thing

in terms of my air cooler = Thermaltake Sonic Tower pictured in my thread http://www.xtremesystems.org/forums/...ad.php?t=88876

http://img224.imageshack.us/img224/1369/setup9ze.jpg
02-20-2006, 11:55 PM
mursaat

Quote:

Originally Posted by HARDCORECLOCKER

Well, after collecting some experience I'd rip it off from any CPU:

After a lot of reading, I'm willing to remove the IHS. I use TT BT. When mounting, do I have to put anything between the BT and the chip? I read somewhere some old Tbird rubber pins, but I don't have any. Is that absolutely necesary? Also, the amount of AS5 should be much less than with IHS (I assume because the are is way smaller) Thanks!
02-21-2006, 12:26 AM
HARDCORECLOCKER

:D After removing the IHS I prepare the chip with 4 small pieces of Armaflex - only that large to fit to the 4 corners without hitting any IC on the PCB.

U can cut them easily out of those Armaflex rolls with a skalpell.

I get them to the PCB with 4 small drops of Arctic Ceramique - doesn't do any harm to the PCB, keeps the Armaflex pieces in position and is easy to remove with some Acetone.

When U get the cooler to the DIE now it will always connect in the right angel without cracking the core.

Straight pressure never is a problem - I gave so much pressure to the naked DIE caused in bending my aluminia made holding clip for the cooler !!!:eek:

Had to use a hammer and a wooden block to get it right again.

So in my opinion pressure is no problem to the naked DIE - as long as it takes place in the right angle.

:toast:
02-21-2006, 05:09 AM
kiwi

If you think what you are doing and if you are careful then there should be no problem

AP0ll0UK:

I am still testing my cpu. We will see :)
02-21-2006, 06:31 AM
HARDCORECLOCKER

Quote:

Originally Posted by kiwi

If you think what you are doing and if you are careful then there should be no problem

AP0ll0UK:

I am still testing my cpu. We will see :)

:D lol - I don't only "think" what I'm doin' - I also do it:p: :p: :p:

Funny word salad here - f...ing english language......... :slapass:

:toast:
02-21-2006, 07:02 AM
mursaat

Quote:

Originally Posted by HARDCORECLOCKER

:D After removing the IHS I prepare the chip with 4 small pieces of Armaflex - only that large to fit to the 4 corners without hitting any IC on the PCB.

U can cut them easily out of those Armaflex rolls with a skalpell.

I get them to the PCB with 4 small drops of Arctic Ceramique - doesn't do any harm to the PCB, keeps the Armaflex pieces in position and is easy to remove with some Acetone.

When U get the cooler to the DIE now it will always connect in the right angel without cracking the core.

Straight pressure never is a problem - I gave so much pressure to the naked DIE caused in bending my aluminia made holding clip for the cooler !!!:eek:

Had to use a hammer and a wooden block to get it right again.

So in my opinion pressure is no problem to the naked DIE - as long as it takes place in the right angle.

:toast:

Thanks a lot for the help :) but.. sorry I have no idea what Armaflex is so I'm researching (googling) now :D. I also need the correct blade (have some tajima cutter ones, but I'm afraid those are very thick).

Anyway could you send me any photos? Thanks again!
02-21-2006, 07:12 AM
HARDCORECLOCKER

Quote:

Originally Posted by mursaat

Thanks a lot for the help :) but.. sorry I have no idea what Armaflex is so I'm researching (googling) now :D. I also need the correct blade (have some tajima cutter ones, but I'm afraid those are very thick).

Anyway could you send me any photos? Thanks again!

http://img226.imageshack.us/img226/6172/ihstool2yt.jpg

:D This is the right tool - do NOT use anything else. Only a razor blade is thin enough to do the job and the plastic case of the ceranfield cleaner prevents the blade from cutting to deep - U can't damage the ICs so.

I replaced the blade on the pic with a newer one before I started.

ARMAFLEX is insulation stuff for tubes to keep 'em cool or hot.

:toast:
02-21-2006, 09:43 AM
mursaat

Again, thank you very much HARDCORECLOCKER :)

Now I'm gathering the nuts to try that first on a 3200+ Venice that "only" does 2600 and I've found is impossible to sell.
02-21-2006, 01:11 PM
HARDCORECLOCKER

Quote:

Originally Posted by mursaat

Again, thank you very much HARDCORECLOCKER :)

Now I'm gathering the nuts to try that first on a 3200+ Venice that "only" does 2600 and I've found is impossible to sell.

:D Good luck - I love to make ppl happy........:)

Kind regards to Spain, my favourite country in Europe...;)

:toast:
02-21-2006, 02:19 PM
mursaat

Quote:

Originally Posted by HARDCORECLOCKER

:D Good luck - I love to make ppl happy........:)

Kind regards to Spain, my favourite country in Europe...;)

:toast:

Mine too :p:

Show 100 post(s) from this thread on one page