Printable View
Nice setup!
Kind of OT, but, How hifg are you getting on your redlines?
I have a problem with my rig, my venice can run prime stable at 3200mhz, but, I cant go higher than 250mhz on the redlines no matter what rail I use, 3 or 5v, no way.
The only way I can go up to 3250 stable is using 2xhtt and 1/2 divisor (100mhz) on the memory.
I tried 4 3200 venice and tccd or redlines, and no go.
I'm using 702/2 bios, and revision of my motherboard is AB0...
enb-2-2-5-2-7-16-2-2-2-2-2556-1-enb-increase-0-7-3-7-Fastest-4-16-enb-16-7-enb
<a href="http://img376.imageshack.us/my.php?image=2729oz.jpg" target="_blank"><img src="http://img376.imageshack.us/img376/1144/2729oz.th.jpg" border="0" alt="Free Image Hosting at www.ImageShack.us" /></a>
Thanks, I will try it
Here are some new results.. :)
<a href="http://img183.imageshack.us/my.php?image=54415154wi.jpg" target="_blank"><img src="http://img183.imageshack.us/img183/5745/54415154wi.th.jpg" border="0" alt="Free Image Hosting at www.ImageShack.us" /></a>
<a href="http://img121.imageshack.us/my.php?image=img01417ab.jpg" target="_blank"><img src="http://img121.imageshack.us/img121/5161/img01417ab.th.jpg" border="0" alt="Free Image Hosting at www.ImageShack.us" /></a>
Very Nice :) and Clean Job also .
Temps under full load 3132Mhz 1.776V
http://www.shrani.si/pics/img_0007110220_thumb.jpg
Idle temps
http://www.shrani.si/pics/img_0023110221_thumb.jpg
That's a nice result for temps. :)
I used the same compressor on my big single, and funny enough I got virtually the same temps under load. That's a really nice compressor, the MP14FB.
Your unit looks great, and is doing a really nice job :)
Gray
New better temperatures...
http://www.shrani.si/pics/-64150637.jpg
wow, nice! What did you change? :slobber:
Very nice!
Two questions :
-What fitting do you use to plug the flexible to your comp? Conversion?
-Is the comp noisy?
Keep it up :)
Its ss hose with 2 connectors.On one side its 5/8 unf male connector,which came connected to flared copper pipe.
http://www.shrani.si/pics/dsc01653155078.jpg
On the other side its 5/8 unf female and its connected to evap.
http://www.shrani.si/pics/dsc01111155077.jpg
looking sharp man.
Thx :)
:D
Very nice unit btw :toast:
Nice :slobber:Quote:
Originally Posted by sharp
I plan to find to female 1/4 connector, than solder them on a hose on which I will cut both ends. Think it's safe? Possible?
This hose is 15 mm large?
Coming along nicely Bro :woot:
Cold ice can you give the Best.-Nr.-Suche:of that sleeving?
tnx
This phase-change looks tidy and cery cold;)
Quote:
I need sleevings for flexibile tube
http://www.rs-components.at/cgi-bin/...id=-1637639964
Woo :woot:Quote:
Originally Posted by LitleDevil
How much loaded ?
Regards
Peter
What did you change from the first time you ran it? You were in the -50's at first now you are in the -60's
nice unit :)
You mean to braze male connectors on both end of hose and connect it with flared copper pipe?That is what i will start to do from now on.Female connectorsQuote:
Originally Posted by Shinuza
is hard to find.
Hose id is 10mm.
Bestell-Nr.: 544532 - 62 on conrad.atQuote:
Originally Posted by Jort
Any news ice?
Amazing... last time I saw below -60c on single stage of mine was I didn't quite finishing charging it up for load and forgot left it running for a while while on the phone :P If that is for load tuned system idle temp... phew... impressive to say the least.
maybe its winter there and he just took it outside :p: jkQuote:
Originally Posted by epion2985