hound if you want bh 5 mem type take a look of the new geil one W is FAST and low timmings really impressive
Printable View
hound if you want bh 5 mem type take a look of the new geil one W is FAST and low timmings really impressive
man, love your 300mhz at 2.5-4-3, that looks like the sd cure dont have any problem with a high htt.
any way very nice oc, i will get my 57 soon and check it out :toast:
Agent allready explained how to go in diagostic boot, i can explain how it works.Quote:
Originally Posted by .HoUnD.
Diagnostic boot will load al the stuff allready before booting so lets say about the half of youre memory will be used. So this will get you a more stable OS.
The second thing is that when using clockgen, you are allready in youre OS so the thoughest part is allready done.
This one will hopefully give youre awesome chip the 3.7ghz. And you will have the fastest fx57 i ever seen on a single stage. So when cooling with Dry ice or cascade this would be a killer chip.
Thanks guys for all the great comments. Im researching the clockgen now. I know it will do the 3.7ghz and I will post the ss ASAP as time permits.
But for now here is a SS of
Prime Blend Stability at 3402Mhz !!
http://www.hillbillyoc.com/3402@1.60vPrime95.JPG
Well after using clockgen I think I was about at the chips limits at 3612mhz @ 1.68V
I could only achieve the following after about 30 mins of goofing off. I think the Vapo has reached its limits as raising the VID didnt seem to help. I went up to about 1.76V trying to hit 3700mhz.
At 3709 mhz I could not complete a SuperPi 1M run. It ran windows fine but would error on 1m
But I hit a little higher at 1.68V with a 14X multi. RAM is extremely relaxed just to isolate the CPU. So the times were down from my 12x301 run.
http://www.hillbillyoc.com/3623@1.68vSuperPI1m.JPG
hiya,
wow, what a nice cpu :slobber:
better than my new cpu, not stable @ 2600mhz :@ but I think you've got a good week.
xyus
at 3.7G....try it the other way around and drop down a notch on your vcore instead of bumping it up, you'd probably overloaded your LS so keep the temperature down with slightly lower vcore if possible
I'm waiting a Vapo LS...I have bench with my FX-57(0516wpmw)watercooled(room temp 25-26°)maximum @ 3252mhz and 26.016 on SPI mod...do you think that with Vapo it's possible also for me to take the 3.6ghz?
Tks...
I would definetly say your vapo can't take it :( my Mach GT can barely handle my FX55SD @ 3.5Ghz 1.64 about 175 Watts... Your Fx57 @ 3.6Ghz 1.68 is running at just under 200 Watts of heat pouring out which is about the limit, unless yours is a Vapo LS
My Vapo it's an LS...the LS has a cooling performance of 200W @ -25 right?!Quote:
Originally Posted by LivingL@rGe81
Very nice 3.4Ghz with SP2004, man! I like it a lot, even though it's a short run ;) But you definetey need some great low-latency 1Gb kit to give it more justice! It would bring your 1M below 23 easly. Good luck!
nice clocks guys
my FX-57 is burning at 3186MHz with a temperature of 49-51C :)
I thought.. it's possible on a cascade system or LN2 (extreme cold) and a FX-57 performances aren't as good as a WC or AC at same frequencies?
just a question
.HoUnD.
I would agree with some of the recommendations made earlier. I would back off VCore a little. FX chips consume more power and generate more heat. And with single stage cooling, raising VCore can sometimes be self-defeating. Don't rely on the voltage readings from CPU-Z or SmartGuardian. Use a multimeter and measure the voltages on the board. On my DFI board, when CPU-Z reads 1.632, the actual voltage is 1.675. Big difference.
I would also look for TCCD/TCC5 that can run 2.5-3-3 timings. 2.5-4-3 will kill you in SuperPi. Or, find some low latency memory like old BH-5 or UTT.
Good luck.
G.Skill PC3200GH is sposed to easyly get 2-2-2-5 1t@250 most seem to get 260 and it aint that expensive (nobody here seams to care anyway though)
I have OCZ el pc4000gold VX and I also take easyly the 250 @ 2/2/2/5with 3.3V...difference with low cpu speed(3236mhz & OCZram),with the Vitesta 566(3252mhz & Vitesta) in super pi
of 0.3" less...low timings are better unless you run bus over 300...
sorry for my english :(
I got the same cpu it will do 300 x 12 on 2 sticks of 512 but not on 4 sticks each individual stick will do 300 lol???
http://gallery.greatestjournal.com/a.../normal_pi.jpg
http://valid.x86-secret.com/show_oc?id=32956
Very good result...what initials have your FX-57?Quote:
Originally Posted by fatty
I'll test the difference between a wc and cascade
at for example 3260MHz
on wc I do 24.9, I hope to get 24.9 too on cascade
I'll be fixed if with a cascade the scores are worse
Quote:
Originally Posted by nachthymnen
Same as hillbilly's 0522 xpmw or something
Diagnostic boot will allow you to do PI runs without anything running in the background to slow your times down. Its also a good idea to ditch the background when benching.
Looks like a great chip btw :)
Hey guys.. good to see everyones results.
I just ordered 2x512mb Mushkin Redline PC4000 !
I should receive in a couple days and I will update this thread for better SPI times + Max OC with the suggestions on Vcore given here. I will also try and find a higher SP2004 mark. I use this rig 24/7 so stability is a must for me.
Cya in a few !
With a little less VCore and a little more tweaking, you might be able to do this. ;) I'm using a stock Vapochill LS. Almost have it stable at 3660MHz.
http://img.photobucket.com/albums/v38/ds7510/FX22.jpg
That's mighty impressive Sierra!!!! Keep it up!!
I want the smileys back, damnit! My posts are lacking proper emotion!
Wow stock vapochill ls, looks like a def 4ghz chip you got there, what week is it?
Chip is week-16, just like what a lot of others have.