LBBLE 0516CPBW OEM from monarch I picked up this past Friday afternoon. Here is what I've got so far. I will do more stability testing and report back later! :toast:
Printable View
LBBLE 0516CPBW OEM from monarch I picked up this past Friday afternoon. Here is what I've got so far. I will do more stability testing and report back later! :toast:
Here is 5+ hour Prime @2.7GHz LBBLE 0515GPBW 3200+
http://premium1.uploadit.org/WaterGu...-Sts-Small.JPG
howdy. just got my 3200 venice from monarch - two days earlier than the tracking info said - ADA3200 AA4BP
LBBLE 0516EPGW
i am just screwing around with this until my 3700 sandy retail shows up. then this will be demoted to my kid's box. just swapped out my winny for this, no other changes. this was taken on my second boot - up
http://www.flickr.com/photos/33178210@N00/12075271/
cpuz validation # 15508
notice cpu temp and vcore. using xp90 and medium speed panaflo. ambient here is around 68F. been running at this speed for around 8 hours doing light work and interweb stuff. i dont think it has much more in it on air. clocks about exactly the same as the 3200 winny. the sandra memory score seems a little shy. i will flash to a better bios for venice and do clean install, then maybe some stability stuff and 3dmark. maybe a little disappointed after big build up. see what happens after burn-in, etc.
i have never posted photos/screenies etc to forum before so if i am doing anything wrong please let me know.
very truly yours,
politenessman
3200 venice 307x9 1/1 2.5/3/3/8
xp90 medium speed panaflo
ultra d
x850xt
2x256 g.skill la 440
550 trucontrol
2xraptor raid 0
2xmaxtor 300gb 16mb buffer sata raid0
How about 32M SPi @2.8GHz? This LBBLE 0515GPBW 3200+ seems to be a very good chip.
http://premium1.uploadit.org/WaterGu...v-SPi32M-s.JPG
got my 3500 today :)
LBBLE 0515 FPAW
testing in a DFI Ultra-D (BIOS 3/10p) with 1 Gig of OCZ PC5000 (DFI "special" TCCD) OCZ PS600 PSU with a TT HSF...XP-90C should be here tomorrow ;) (good thing too since its hittn 56C :eek: )
this is only about 1.5 hours of testing but...its P95ing @ 285x10 @ 1.648V (according to CPU-Z)
this set-up couldnt get a 3200 CBBID Winnie stable @ 2.4GHz and now its running @ 2.85GHz (on AIR!!)
-----------------------------------------------------------------------
ran 1 hour of P95 @ above settings...no errors....
right now im testing 320x9 (2880MHz)....seems stable (3-4-4-10)
BSOD @ 300x10 (didnt think it would go but had to try)
id thro more Volts @ her, but the temps are too high. we'll see how the XP-90C and a Nado help that ;)
--------------------------------------------------------------------------
i dont have this thing networked so no screen shots (youll have to trust me)Quote:
Originally Posted by Sucka
285x10 ... 1.6V core ... 2.9V mem ... 1:1 ... 2.5-4-3-10 (too many others...but well just say loose) x850-XT @ 570/594 (mild OC)
S-Pi 1M: 30
Everest:
read: 6349
write: 3440
Lat: 38.0
SANDRA:
Mem band-W: 7611/7529
CPU: 12,378 ... 4673/6073
MM: 27,145 / 29,303
3D 01:
31,463
PS working on tightening the timings since sticks are rated @ 312x 3-4-4-10
probly over the weekend, ill thro in some UTT and "clasic" BH-5 and see how they go
got a screenshot: :fact:
http://img124.echo.cx/img124/2427/2850mhz5sf.jpg
Just received my OEM 3200 Venice from Monarch today :D
ADA3200DAA4BP
LLBLE 0516 EPGW
Z639006D50906
I'm using the XP-90 heatsink with a relatively quiet 90mm fan, and very thin layer of AS5 only, flashed the 414-3 Bios on my DFI Ultra D motherboard and it picked up the Venice on the fly, no time for messing around so I jumped straight to 290 x10 @2.9Ghz with 1.50v, can run a bunch of benchmarks and SuperPI 1M for fun but won't bother to take any screen shots because they mean absolutely nothing to me because it's not 100% stable, so scratch that, load into the BIOS again and lay the hammer down on the vcore and settle on 1.66v, but SuperPI 32M crapped out at "21 finished" then BSOD.
OK, something gotta give right? so I Back it down to 285 x10 (2850) and boost the vcore up to 1.71v, temperature was looking unbelievably good in the BIOS, so I ran the Memtest #5 and #8 for about 30 error-free passes again, then boot into Windows XP, room temperature was around 22'C and cpu temperature idle at 27'C....sweet!!! Fired up the SuperPI 32M and crunch away.......Bingo!! I hit the jackpot :D :D under load temperature is surprisingly low at only 42'C!! :slobber: Unlike the Winchester I had before...this Venice thrives on higher vcore, since 1.71v hasn't put a dent on the under load temperature I'll shoot for 2.9Ghz again with higher vcore, maybe 1.75~1.80v. I can't help but wonder how good is the 3700 San Diego that I'm going to receive from Monarch in a week or so. :D For now I'll settle on a rock solid 2850Ghz @1.71v AIR COOLED!!! and going to watch a movie...this chip rocks!!!!
:banana: :banana: :banana:
http://www.xtremesystems.org/forums/...chmentid=29723
Edit: I think I better off running 317 x9 @2.853Ghz, this is about as far as I'm willing to run 24/7 till I get my 3700 SD :D :D
http://www.xtremesystems.org/forums/...chmentid=29734
Another shot at 2.862Ghz:
http://www.xtremesystems.org/forums/...chmentid=29779
This might be what we considered the 'Sweet Spot', only required 1.58v to hit 2.808Ghz on air.
http://www.xtremesystems.org/forums/...chmentid=29786
Keep on torturing the chip LBBLE 0515GPBW 3200+. SuperPI 32M @2.9GHz here.
http://www.anti-x.org/bbs/attachment...v-SPi32M-s.jpg
Here is my 3000 with XP-120. On air that is.
I can actually go higher with more voltage but this is good enough for me.
here is my 3000+ on air...... still not broken in yet..... I hope there's more left in the tank...:D
2900MHZ stable so far. Love this chip!
Now stable at 2.7Ghz and climbing.....
http://www.xtremesystems.org/forums/...chmentid=29819
SuperPI 1M @3GHz from a watercooled LBBLE 0515GPBW 3200+ here.
http://premium1.uploadit.org/WaterGu...6v-SPi1M-s.JPG
use the latest 24.11 version of Prime95 for real stability (v24.11 is optimized for Athlon64 and therefore tortures the CPU much more than any 23.x code).
Prime95 v24.11
http://mitglied.lycos.de/xxmartin99/...2825@1.650.png
SuperPI 32M (mod 1.4)
http://mitglied.lycos.de/xxmartin99/...i_2820_32m.png
SSE3 gives a nice boost
SuperPI 32M (SSE3 Patch)
http://mitglied.lycos.de/xxmartin99/...0_32m_sse3.png
Almost 0.1V difference between SuperPI 32M and Prime95 with passive watercooling.
Quote:
Originally Posted by TheMeatFrog
Damn, TMF! You got a really nice 3000+ :toast:
i wish mine could do that.
Here's the same oem from Monarch. It just came today. Here are preliminary results using a Zalman CNPS7000B-ALCU. Ambient air is around 23.88c. (do you like that precision?)
1.425 x 126% DFI nf4 ut-D won't go far on stock volts.
I need to work on her a bit more... BRB
http://www.xtremesystems.org/forums/...id=29874&stc=1
http://www.xtremesystems.org/forums/...id=29877&stc=1
Had some store credits with Ncix.com and decided to spend it. Got a week 516 3000+ Venice and first boot 2.7GHz no sweat. Prime stable too.
http://members.shaw.ca/spicy/blah.jpg
E3 3500+ @1.6 @ 2.86ghz
DFI NF4 SLI-DR
VX500 2-2-2-5 @ 3.3
It won't run stable at 265fsb and I'm positive its the ram So I might just lower the timings to avoid voiding my warrantee
OEM 3200+ LBBLE 0516EPGW from Monarch
9x316 Memory running 1:1 DDR632
Air cooled by the XP-90 in my sig :)
SuperPI 1MB
http://img170.echo.cx/img170/5999/superpi1mb9ts.jpg
SuperPI 32MB
http://img170.echo.cx/img170/9503/superpi32mb2gk.jpg
Here's my very first OC screenie. This is by no means the limit, just something to get started. Once I leave it Priming all night tonight, I'll keep going tomorrow. Keep in mind this is at 1.4v:
http://img.photobucket.com/albums/v428/Tibu/2.jpg
I got my 3500+ Venice today :banana:
Quick try 2835Mhz 1.7v
Water temperatures +27C but the processor was +50C in test. I've to check the touch of core.
Still not fast enough! :eek:
my 3800+ bench in AC ,XP90+Papst 90mm
Venice Step
O/C Venice
After fighthing with my vid card I was able to overclock the new VENICE
I hand picked the cpu at the local store
ADA3000DAA4BP
LBBLE 0515FPMW
My first 2.8ghz bench on air. I know it can do it at lower voltage, I just upped to 1.6v for curiosity's sake. Theres still much more in this chip, will go higher later. And ignore the low 3d01 score, I changed driver to 76.50 and lost 5000 points go figure. Ima get the XG 76.45 drivers and see if 3d01 is better.
http://img.photobucket.com/albums/v4...sbbenchies.jpg