Quote:
Originally Posted by trans am
That's why you guys never seen I did that 3-4-4-8 relax timing.. I am always do at lease CL=2.5;)
Bear with me a while, you guys will know how far LA can go! :D
Printable View
Quote:
Originally Posted by trans am
That's why you guys never seen I did that 3-4-4-8 relax timing.. I am always do at lease CL=2.5;)
Bear with me a while, you guys will know how far LA can go! :D
Will try today on a volt-modded EPoX 9NDA3+. Will post results. :D I know the AV8 is not the best choice for overclocking... but still... it's not as bad a board as one might think.Quote:
Originally Posted by IvanAndreevich
How about 3-3-3-x?
could care less about cas latency, its TRCD and TRP that matter..
to varzmaster:
As the VIA chipset,Your testing report is very nice :)
to STEvil:
I will do the testing later.Thanks for your opinion :)
The limits of p revious Testing report is located 600.And it can pass memtest86.This is just testing in the MHZ.
I have no tested the extreme performance and best-optimized –parameter. If I have more time, I will do this testing parameter-value.
thanks :)
DDR600 1T 2.5 3-3-5 :p:
http://hkp2p.shopping7.org/~hardware...200511/335.jpg
DDR600 1t 2.5-3-3-5?..too easy..:p
hahahahaQuote:
Originally Posted by Onepagebook
it is ok
DDR650 1T cl2.5 4-3-5
http://hkp2p.shopping7.org/~hardware...200511/650.jpg
ok...next..:D
DDR625 1g(512x2) "1t cmd"2.5-3-3-5
not photoshop..:D took it from digital camera..;)
http://www.devilsword.com/ms7125/ddr6251t.jpg
Hey, your monitor is almost as big as mine ;) :D
Corsair rev 4.1 do better than my G.Skill sorry :(http://img.photobucket.com/albums/v5...M/a2a89da7.jpg
You guys are just tearing t up.
I really would like to see some 2-2-2 at 300.
Well...I'm impressed.
I have a P4 2.4C that I run at ~282fsb. So I am looking for a 1GB set (512x2) of RAM to run at tight timings at 282 1:1.
I'm about to pull the trigger on the GSkill PC4400. However, there are so many variations (i.e.: LA, LC, LD, LE).
Based on GSkill's specs, I would think the LE would be best. But I saw a post somewhere that indicated that the LA is preferable for highest overclocking speeds at tightest timings. I'm confused.
Which one is best for my situation? :confused: Thanks for any help!
Who doesn't? :DQuote:
Originally Posted by althes
Still DDR 625 with 2,5-3-3-5 timings ain't bad at all for 2x512mb with 1T CMD.
300 2-2-2 isn't going to happen with anyting other than some xtreme BH-5 and some ugly voltage.
And then again, not with 2x512mb. :(
so great :p:Quote:
Originally Posted by Onepagebook
[QUOTE=Zanr Zij]Corsair rev 4.1 do better than my G.Skill sorry :([QUOTE]
haha dude, did you see mine is [color=red] "1g dual channel DDR625 2.5-3-3-6"...not 256x2?
:p:
Stevil...my monitor?lol it's apple 23" LCD :D
yeah, all i've got is a 22" flatscreen CRT :P
Stunning results. Timings are not on the strong side but those ras-cas 3 results are pretty remarkable :toast:
And yes OPB that is a biga$$ monitor - It really dwarf´s my 19" tft :( :hehe:
:ROTF: :lol: :rotf:Quote:
Originally Posted by Kanavit
dmn, well.. since FX-55 has a good int. mem. controller and the board is NF4.. this is still impressive.. :slobber:Quote:
Originally Posted by Onepagebook
I hope, that in Q1 of 2005 new A64 CPUs, which would have SSE3, less TDP (+DSL) & a better/improved/rev. mem controller would score something like the same on a DFI NF4-Ultra.. :D :D
Quote:
Originally Posted by trans am
LA DDR400 2 2-2-5&DDR600 2.5 4-4-8 256MBX2
LC DDR400 2 2-2-5&DDR550 2.5 4-4-8 256&512MBX2
Sell in newegg...
http://www.newegg.com/app/ViewProduc...231-007&depa=1
thanks wwme. I have a set of 2x256 LC. I haven't played with them yet, but we'll see. Been too busy with the twinmos. I think I'll put the gskill in now. BRB.
Quote:
Originally Posted by trans am
TA..fire them all the way over 300.. :D
OPB
Quote:
Originally Posted by Onepagebook
oH BOY. It was not a pleasant overclocking experience. :(. THese wouldn't do the rated timings and speed of ddr550 at 2.5-4-4-8 2.8-3.3v. I just got these last week. I am going to call newegg and see if they will take them back, hopefully they will let me upgrade to pc4800 LA. Those look pretty good! the dates on these are kinda old too. week 31. most of my tccd from 31 we're not very good. I think I'll keep the VX in for now. oh well. :shrug:
http://www.xtremesystems.org/forums/...id=22263&stc=1
Quote:
Originally Posted by trans am
what is your MOTHERBOARD?
Overclocking is not the AMD.Motherboard ,promise cpec.
CPU&Motherboard can access 200MHZ,RAM access 300MHZ
Like Msi_NEO2, 2/3 can pass 300MHZ.
1/3 can not pass 300 MHZ If we make the RAM of pass DDR600,it will be error situation in this Motherboard.
my test
neo2 2.85v
http://hkp2p.shopping7.org/~hardware/TEST/DDR/M670.jpg
9nda3+ 2.8v
http://hkp2p.shopping7.org/~hardware/TEST/9NDA3/670.jpg
neo4 2.85v DDR682 1T CL3 4-4-8
http://hkp2p.shopping7.org/~hardware/TEST/LA/M1T.JPG
In this high MHZ, It must depend the CPU,MOTHERBOARD,RAM.
[QUOTE=windwithme]what is your MOTHERBOARD?
Overclocking is not the AMD.Motherboard ,promise cpec.
CPU&Motherboard can access 200MHZ,RAM access 300MHZ
Like Msi_NEO2, 2/3 can pass 300MHZ.
1/3 can not pass 300 MHZ If we make the RAM of pass DDR600,it will be error situation in this Motherboard.
thanks wwme, but I have many sets of tccd and I've tested them in the same board with the same tried and true settings. I attached an error log from memtest86 so you and OPB can see they are POS sticks. I'm really surprised these sticks couldn't even pass at rated speeds and they are just 2x256. THese should have no problem with this rig. I think I just got sticks that are bad. Maybe shipping damage or ESD damage. THis is my first run with Gskill but I am not giving up. A friend of mine(klisp) just got the same sticks and he also had problems. :shrug:
here's pdp tccd on same board....
I didn't bother with ras-cas 4.
Yes, it's stable.
Like tony mentioned earlier.
the ras-cas 4 on k8 is really a ball buster.
It's the equivalent to bringing sand to the beach.
http://xtremesystems.org/forums/atta...chmentid=19631