ahhhh attack of the animals..... even master of the puppets changed his icon..... btw good job :thumbsup:
Printable View
ahhhh attack of the animals..... even master of the puppets changed his icon..... btw good job :thumbsup:
Don't worry, I got my old avatar saved on my HDD. The cat in the pic is a bengal cat. I got 2 bengal cats but I havent got any good pics of them :(
Didn't hipro modify his prom to R410???
I think I remember him saying that...
IMO he got pretty good temps, but dunno if he's using 100% of R410.
Good job, Chilly :thumbsup:
Wish I would live in the states. I have an empty Mach1 here and cannot fix it here in Germany. :( That would be a mod I would appreciate to have ;)
there is a guy in holland who makes and fixes proms and other P-C stuff!Quote:
Originally posted by SAE
Didn't hipro modify his prom to R410???
I have an empty Mach1 here and cannot fix it here in Germany. :( That would be a mod I would appreciate to have ;)
Haeg koeling :toast:
it's only 550km away from magdeburg :D
It depends on the ambient, Hipro's room temperature might be a lot colder over in Greece giving him a lower condensing pressure. If I do it to my Prommy over here in Singapore with usual ambient of 30C, I think it will be dancing on its feet :)
i really wish i knew more about this stuff:confused: I may be forced to have you do this to me mach1 :D
-52c at 150W is plain enough for even me tho:D What ambient temp is that at?
When I was on the phone with Chilly I belive he told me he had it set up in his garage and it was 80 deg and was holding that temp 4 a 24hr period.Quote:
Originally posted by Mongoose420
[B
-52c at 150W is plain enough for even me tho:D What ambient temp is that at? [/B]
nice, im in good old PA where it rarely gets above 90F outside. I could easily hold that indoor temp year round.....:rocker:
Sorry, too much coffee for me today...
I didnt monitor it too closley but it was aroungd -51 to -52 every time I looked I ran it for a day..
no updates? or did you decide on the 80/20 507/410 mix?
Just got in from a busy day tried a 40% 410 blend too much head pressure, I have another blend I am going to try, Working on the modifications now more tomorrow evening.
ah, this should be very exciting. -60 on single stage at 150w load.
I've moded my Mach1 unit with pure R410 gas with the same condenser and with two Delta 12x12 cm 190 cfm working push-pull (one in front of the condencer and one in back of it)......I also have changed the capillary tube with a No4 one (2.5mm outside diameter)......ALSO afterwords I changed the Compressor with a SC12CL one for 404 gas......My room temp is about 27*C and I get -22*C max on Promie's head on a P4 3.4GHz EE CPU at 4600MHz with 2.1VCore......That's about 230 to 240Watts heat......No matter what , niether R404 nor R507 couldn't hold the wattage of the CPU and the temps where rising and rising......Only the R410 could and can handle that wattage with the default Promie's head........Another head needed for more power consuption....... ;)
http://www.thelab.gr/images/Hipro5/T...ressor_jpg.jpg
nice job, i would love to do a mod like this on my prommy, but i already get -50, maybe the extra 12 degrees wouldnt do much
The R410/blend mod with stock compressor will do better temps and loads but it is also more susceptible to ambient fluctuations. -25 to 30C in bios is about the limit head temp loaded around -45 to -50C. All in all the 507 mod is the best for the prommie.
Agree........Quote:
Originally Posted by chilly1
Hey Chilly, whilst your in the mood for some extreme prommy mods try some R1270 (propylene). The PT chart is very similar to R404a/R507 but this gas is way more efficient. Could possibly be used at low suction pressures (10" Hg)and still maintain the good capacity (eg 200W).
Will do I can get that tomorrow... I will also load test it and see what happens.. I got a 300w dummy load.
A modded mach II with new cap tube and a blend of r404a (90%) and R410a (10%).
Would it be possible to do this with the stock condenser ?
YES :)Quote:
Originally Posted by Mima
I did it too Fosco's mach2 and it works realy good. But i dont know how good it is for the kompressor. ....too run 24/7
Hi,
Very nice chilly!
Just one question, what load ya using....reason i ask is , that doin the math, i cant see how on earth you get anything below -50c evap temps with a 150 watt load (overclocked FX/EE sorta cpu loads) with the 1/3rd (almost) HP prommy compressors....unless thats the prommy nonsense temp reading!
very facinateing work Chilly, quite impressive. I wonder what you could do on a single stage with say a 1/2 or 3/4th HP compressor.
Good luck man
I have a pretty good handle on how to tune single gas mixtures ie.
Any tips or shortcuts for tuning these multi-gas single stage coolers guys?Quote:
Originally Posted by MaZeR