Yes of course, but since UD9 using XL-ATX form factor, you need the chasis with minimum 8 explansion slot bracket, so i think no problem.Quote:
Originally Posted by Musho
Printable View
Yes of course, but since UD9 using XL-ATX form factor, you need the chasis with minimum 8 explansion slot bracket, so i think no problem.Quote:
Originally Posted by Musho
qft :)Quote:
Originally Posted by Dainas
9! You need a case with nine brackets minimum, 10 for quad dual slot GPU action.Quote:
Originally Posted by Benny Lodewijk
Anyway to me both current XL-ATX enthusiast boards equal lazy PCB engineering. Only 7 slots, yet taking up 9 PCI brackets worth of space? It's entirely possible to make these features work on an EATX board like ASUS demonstrated a couple of times now (P6T7, RIIIE). If trace routing is such an issue I'd personally rather pay for a 10 or even 12 layer PCB and a fully copper active chipset cooling solution (two NF200 = ~40 Watts extra to shed) than a new big ass, ugly case.:down:
Quoted for truth. But then again, people that have enough money to buy these kind of systems usually don't mind spending a bit more on a new case. So they aren't losing that many sales by cheaping out on the design. Why do you need 10 brackets for quad GPU though? 1 for the hybrid silent pipe plus 2 per GPU ends up requiring 9 for quad GPU, right? :confused:Quote:
Originally Posted by sholvaco
^
You need 10 because both boards skip the first two PCI brackets in order to fit all their junk there (one of the two NF200, NB, uncore PWM...). The first PCI slot lines up with the third PCI bracket on a case while the last, seventh slot lines up with the ninth bracket. A dual-slot GPU in the last slot overhangs the motherboard therefore you need 10 brackets.
Just a personal opinion, but all of the cases able to fit these so far are dead ugly to me (yes even the Lian Li). So even if I had all the money in the world... :p:
which cases can hold this monster? thanks.
Corsair 800D does with a minor mod :DQuote:
Originally Posted by HelixPC
copper mate..........GIGABYTE's had copper on their borads for a loooong time... :)Quote:
Originally Posted by Bodkin
http://www.gigabyte.com.tw/FileList/...off-charge.htmQuote:
Originally Posted by kromosto
Quote:
Originally Posted by DuraN
Quote:
Originally Posted by M.Beier
:rofl::rofl::rofl::rofl::rofl::rofl:Quote:
Originally Posted by DuraN
first shipments went out end of last week so they will appear in shops next week or week afterQuote:
Originally Posted by systemviper
Street price in Australia is ~AUD$650 (roughly high US$500 price tag for us but we are always more expensive than places like US so i guess just see what they will sell for locally in your country)Quote:
Originally Posted by tajoh111
yeah agreed thereQuote:
Originally Posted by Benny Lodewijk
http://www.gigabyte.com.tw/FileList/...9_caselist.pdfQuote:
Originally Posted by HelixPC
Wouldnt need a 10 slot case if manuf started making single slot brackets for the watercooling crowd....Quote:
Originally Posted by sholvaco
gigabyte said 24phase of UD9 is more advance than 24phase of UD7 ???
Hard to say, the old design seemed to be a 6 phase controller and MUX. Not sure what they are doing with this one. The UD5 VRM actually 'looks' better in the article Dino linked than the UD7.Quote:
Originally Posted by PatRaceTin
They should've just used digital PWM.Quote:
Originally Posted by raju
Maybe gig engineers know something that we don't? :D Who knows... :confused:Quote:
Originally Posted by zalbard
Anyway it's nice looking board, I doubt it would lack some nice performance. For someone that can afford additional PCI-e cards this is really nice board to go with....otherwise..
X58A-UD9 new 24phase DesignQuote:
Originally Posted by PatRaceTin
http://sphotos.ak.fbcdn.net/hphotos-..._1289816_n.jpg
708a vcore output pretty easy to handle gulftown, also the new VRM design has complicate and very smart switch dynamic phase let motherboard more durable and strong.
if you not extreme user, but more focus on engery saver, this VRM design has new techlonlogy, each tiime boot will rotale first pahse to turn on machine, such as first time boot using first phase to turn on, 2nd turn on with 3rd phase automatically, this will reduce RMA risk, give VRM more longer life time, and reduce very boot hit on the same phase.
DES2 with new design
on tranditional dynamic VRM design offers CPU phase depened on loading which
cpu needed. but every time boot the system will from first phase. with engery saver
tool, system might could change the phase for cpu using, like 1 phase or 2 phase when
cpu is idle, so think about this, each time you boot the system and idle system, most of time
power is attacking the first phase, first phase always be use 100%. means if first phase
die then you need to RMA to board.
so take down this,
1. first phase always be used 100%, if die then need to RMA board
with new VRM and energy saving design, system will chose random phase to boot(
yes this is the new technology!), when cpu boot or idle , first phase won't be aways 100%
and not be the only one be attack, so if first phase die, 2nd phase replace to boot system
automatically, if 2nd die , 3rd phase will instead to do this job.
so take down this.
2. first phase won't be hit 100%, lift more longer life span of VRM
if first phase die, the board still work well, casue 2nd phase will replace to do the job.
3. reduce the heater of VRM, if system is idle or light loading, the heater won't be always
on the same phase. system boot to choose each phase to be the master phase.
with DES 2 software, system will auotmatically choose which phase to boot, also provide
dynamic phase change. make a exmaple, when cpu light loading needs 2 phase to work
system choose 1st and 3rd, so 2nd phase won't be use, this function also balance the heater from whole VRM design.
system is under DES2 controlled, and compatible with easytune6, you could do overclocking aslo do the DES2, here is the defination when VRM will use full 24phase
, when cpu is under heavy loading, current over than 80amps of vcore, normally
if you install a 980x processor do a full core task, VRM will run 24phase.
X58A-UD9 is based on this new technology of VRM design, but more complicate
sorry i can't tell whole story, but hope my explaination will help you to understand
gigabyte's new VRM design.
the attached picture like a simple explanation, and comparison with trandition
engery saving VRM design.
X58A-UD9 new VRM energy saving design benefit.
1. balance and reduce the heat of VRM
2. more effiency offer power with dynamic phase change
3. offer more long life span, reducing power attacking the same phase
4. reduce RMA case ( attached picture use 4phase to explain, with tranditional design
if first phase die, then you need RMA, with new design, if you loose phase 1,3,4 board
still alive.)
5. new 24phase VRM and DES2 design, combined with best effiency and powerful
current for cpu using.
backup* if you not install DES2, VRM do full 24 phase all the time.
http://sphotos.ak.fbcdn.net/hphotos-..._4568567_n.jpg
hicookie
It's Available at Newegg for $699.99. 23 are in stock.
http://www.newegg.com/Product/Produc...pk=ga-x58a-ud9
Not sure if it warrants that type of a premium price.
WTH Gigabyte is thinking :rofl:? even EVGA SR-2 is $100 less cheaper than that...damn I was looking forward for UD9, but for at that price I could get a RE3 + memory at least...Quote:
Originally Posted by Kensek
hicookie
can you switch off the ocp in the bios?
I am wondering, where can you buy SR-2 ??? Thing is; someone actually asked me on MSN, and I simply couldnt answer.... It seems to be a not released product...???? A 5-10 sample ultra rare edition???Quote:
Originally Posted by Blacky
BIOS do automatically recently, also we can open a option in BIOS,Quote:
Originally Posted by Hondacity
which one you prefer?
hicookie
Thank you hicookie
new design is very good!!!
So there is difference between ud7 and ud9 24 phase operation after all?
Dual Power Switching is not present with ud7, thus new re-engineered 24 phase power design rotates phases with each initial boot.
Nice reading, thanks hicookie! :)
3. Will switching boot phase make a difference for most of the people that buys these premium boards which will be replaces within a year?Quote:
Originally Posted by hicookie
4. If say one VRM phase dies, wouldn't you want to RMA the board anyway? Even if you could boot and back up your files, and use it while your RMA is being approved, which is the only thing I see a use for this technology.
Also, without the motherboard dieing, how do you know how many phases has died? Does the software report it?
recently saw your 3d05 @ 6.7ghz!!! very very nice world record:up:Quote:
Originally Posted by hicookie
is there a coldbug adjustment possible? were you able to adjust something software wise or hardware wise to adjust coldbug?
is the cpu you used for 6.7ghz es or retail? is this another batch from your previous results?