Really heavy clocking, man! :up:
I guess this is a cpu bonus and does not directly depend on the board's capabilities (leaving out that ASUS crap ;) ^^ j/k).
Printable View
Really heavy clocking, man! :up:
I guess this is a cpu bonus and does not directly depend on the board's capabilities (leaving out that ASUS crap ;) ^^ j/k).
Great bclk Hazzan :clap:
I think you will run better with subzero cooling cpu:D
hopefully Hazzan posts his bios settings for us :D
I ordered mine from the 'Egg last night for $299.99!! :up:Quote:
Originally Posted by tripgood
thanks All Guys......:):):):)
I dont have any special setting on bios:):):) think maybe I just lucky...this my setting :
Quote:
DRAM Timing
Memory Control Setting: AUTO
Memory LowGap: 1024
DRAM Command Rate: AUTO/1N/2N : 1N
CAS Latency Time (tCL): 8
RAS# to CAS# Delay (tRCD): 8
RAS# Precharge (tRP): 8
Precharge Delay (tRAS): 18
REF to ACT Delay (tRFC): AUTO
Write to PRE Delay (tWR): AUTO
Rank Write to Read (tWTR): AUTO
ACT to ACT Delay (tRRD): AUTO
Row Cycle Time (tRC): AUTO
Read CAS# Precharge (tRTP): AUTO
Four ACT WIN Time (tFAW): AUTO
Voltage Setting
O.C. Shut Down Free: Disable O.C.S.D.F
CPU VID Control: 1.4250=================with my Processor
CPU VID Special Add Limit: Enabled
CPU VID Special Add: Auto
Vcore Droop Control: Enabled
DRAM Bus Voltage: 1.78 =============== with my Memory
DRAM PWM Switch Frequency: Reduction 15%
DRAM PWM Phase Control: 2 Phase Operation
CPU VTT Special Add: AUTO
CPU VTT Voltage: 1.55 Volt
VTT PWM Switch Frequency: Reduction 15%
VTT PWM Phase Control: 2 Phase Operation
CPU PLL Voltage: 1.80v
IOH/ICH 1.1V Voltage: 1.21v
IOH Analog Voltage: 1.20v
ICH 1.5 Voltage: 1.7v
ICH 1.05V Voltage: 1.05v
DIMM 1/2 DQ/DQSTB Bus VREF: -00.0%
DIMM 3/4 DQ/DQSTB Bus VREF: -00.0%
DIMM 5/6 DQ/DQSTB Bus VREF: -00.0%
ADDR/CMD VREF Control: Disabled
x DIMM 1/2 ADDR/CMD Bus VREF: 110
x DIMM 3/4 ADDR/CMD Bus VREF: 110
x DIMM 5/6 ADDR/CMD Bus VREF: 110
CPU QPI Drive Strength: Normal
IOH QPI Drive Strength: Normal
Exit Setup Shut down: Mode 2
O.C. Fail Retry Counter: Enabled
O.C. Fail CMOS Reload: Disabled
PPM Function: Disable
Turbo Mode Function: Disabled
1 core Max Turbo Ratio: 26x
2 core Max Turbo Ratio: 25x
3 core Max Turbo Ratio: 25x
4 core Max Turbo Ratio: 25x
CPU Non-Turbo Clock Ratio: 18x
* BCLK/UCLK/QPI Controller Settings *
QPI Control Settings: Enabled
QPI Link Fast Mode: Enabled
QPI Frequency: 4.8GT
CPU Base Clock (BCLK): 223 Mhz
Boot Up CPU Base Clock: AUTO
PCIE Clock: 103 Mhz
DRAM Frequency: 1067Mhz
UnCore Frequency: 1600
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
I will start with BCLK 223 from bios and raise with higher BCLK ...if have some BSOD raise your CPU VTT/QPI Voltage.... step by step..better running with SPI every time you raise BCLK on OS...that my point..:):)
@eva2000 : George..... thanks for your template :)
Thanks Hazzan, the only things I haven't tried much of are
IOH/ICH 1.1V Voltage: 1.21v
IOH Analog Voltage: 1.20v
ICH 1.5 Voltage: 1.7v
PCIE Clock: 103 Mhz
and pushing uncore frequency above 2x dram frequency
so will test and see :D
G'luck!^^ :up:
Keep up the good work ... I want to see some fantastic clocks ... better than ASUS R.E. II ... :rofl:
Thanks all my freind ........:):):)
Nice.... but you can get BCLK on 226 with NB Frek 3600 .......mine BCLk 227 with NB frek 4100 :D:D .......any way nice you BCLK you get there....:up::up:Quote:
Originally Posted by Bootsy