I think it will not fit. I cant slap it on the board because some other block are already on it. But you can see in the pictures. Probably need to mod it.Quote:
Originally Posted by Grnfinger
SB doenst need any WC. Passive or 40mm fan is ok. It just barely warm.
NB get hot and need proper cooling. Finish installing xp with eveything on stock and it already hot.
Mosfet also need proper cooling. It getting hot when priming.
Attachment 88293
Attachment 88294
Hmm let us know if you figure something out. It sure sucks we dont have temp sensors on the NB. I'd really like to know what its runnin.Quote:
Originally Posted by Sparda
What water-block will work on this NB? I have a Danger Den Universal and an EK NB/SB EK6 ... so you think either will fit?
Anyway of putting an external sensor near the chip? If I were to use a water-block on it, would a inline temp sensor give an accurate reading of the temp of the NB?Quote:
Originally Posted by nugzo
Gigabyte is pulling away even farther from Asus's $200-$300 Intel P45 boards.
With the ASUS, we all know pl10 is as low as you can go 1:1.
These UD3's are doing fairly nice for a p45.
Here is my Everest ss 490-530 fsb with 4gb (2x2) Gskill.
These are pretty crappy timings.
I cant wait for my cas4 pi's to get here. Should help a ton.
540 was as high as i could go. Well i made it to windows at 545 and completed the everest benchmark then it froze while saving ss.
Anyone here tried populating all of their memory slots with DIMMS? If so, has that affected how well the system overclocks? I want to eventually get my system to 8GB of RAM instead of the current 4GB with my 2x2GB setup.
I'll be able to try 8gb today. I'll let you know....Quote:
Originally Posted by Sgt_Strider
Any comments on your 8GB setup?Quote:
Originally Posted by nugzo
yeah. all 8gb (4gb gskill 9600 and 4gb gskil 8800) are now bad. Motherboard is toast to. Others are running 8gb fine. I dont know what happend with my setup. I installed 8gb at 500 fsb 1:1 no post. then posted but went into bios recovery. Recovered and posted again. Then no post at all. pulled the board and put in my Maximus 2 formula, used gskill 9600 and hung at detecting ram. tried all sticks 1 at a time and it booted into memtest to get errors. None would boot together in dual channel. Grabbed my 8gb of gskill 8500 and installed into asus and all was good. Yanked asus and reinstalled UD3 with the good 8500 and still no post. Just turns on for a few seconds then shuts down. does this over and over with no output to display. I now have 3 RMA numbers from new egg.Quote:
Originally Posted by Sgt_Strider
thats pretty scary to hear, I just had to RMA my board, due to it just stuck in a quick reboot cycle, and no display. It would turn on and 1 sec later reboot, over and over.Quote:
Originally Posted by nugzo
Thank you for Nuzgo and NapalmV5 for sharing your settings. It's Prime stable but I forgot to save a screenie. I ran a quick OCCT test and a few benchies for a pic. This is what I got 24/7:
http://img170.imageshack.us/img170/980/desktoplf0.gif
mine did that & all i did was hold a screw driver in the Clear cmos leds/pins for 15 seconds & it reset it self to defaults . then it booted just fine .....Quote:
Originally Posted by The Viper
Awesome Golfjam. Your Welcome.
I tried that. Well not with a screwdriver, but same result. I have a switch wired to the clr cmos pins.Quote:
Originally Posted by bigslappy
Mine got stuck in that cycle a bit and all I did was kill power via PSU for a few, then it would start up fine.Quote:
Originally Posted by The Viper
I thought I was doing all good and shiz then I go and see this thread... BAH, you guys are killing me!!!
That's what I've done so far.
I've been running stable at 490x7.5 since the last post in that thread there.
Max I was able to get before going through here was 500x7.5.
Looks like I'm going to have to do some more playing around....
Bastages... lol
You can doooo it. I see 515 in your near future. :p:Quote:
Originally Posted by IFMU
Does any E-tailers have this board in stock? I can't seem to find it. Could someone post a link to a E-tailer in the USA. Thanks :)
Thanks a lot man:)Quote:
Originally Posted by bigslappy
Quote:
Originally Posted by bigslappy
So CHEAP it hurts! :yepp:
At this price, everyone should try one. :yepp::clap:Quote:
Originally Posted by Jor3lBR
And it's even cheaper until 11/20. Just use code EMCBBBEBJ (must be subscribed to their special emails) and get it for $99.99 after AR and you still get a 2Gb flash drive for free.Quote:
Originally Posted by Jor3lBR
My new one came in today. That DFI is comin out fast as it can. Couldn't get past 475 FSB with it (UT P45 T2RS)