DFI Lanparty JR P45T2RS (56k warning)

Printable View

Show 100 post(s) from this thread on one page

10-01-2008, 09:49 PM
grasskicker509

sweet board!
10-02-2008, 11:48 AM
ryboto

I had this board. At 375mhz FSB, the system was completely unstable, random BSODs, or hard locks, or it just would restart when it tried to load windows.
10-02-2008, 02:35 PM
Eldonko

Yeah it seems these things are very inconsistent.
10-05-2008, 11:43 AM
ZoLKoRn

4 Attachment(s)

This bios setting for 580FSB on E8600 :)
10-05-2008, 11:53 AM
Lestat

my board is very unstable also.
i do not like it
its a Rev A3 P45 (per cpu-z)

Quote:

I had this board. At 375mhz FSB, the system was completely unstable, random BSODs, or hard locks, or it just would restart when it tried to load windows.

stop running 4 sticks of ram for starters.
next stop going up in so little fsb steps.
just slam the fSB to 400 then 450, them after that with a quad its really hard, you need to do alot of tweaking.
set vcore accordingly. maybe +.250mv (just to try it, then lower or raise it if you need to)
Just to start with try these settings.
set Nb to 1.45 and CPU VTT to 1.33v (those are bios settings. the actual reading will be a little lower but thats ok)
All 3 GTL voltage settings just leave at .67x (just to get your system running.)

set ram divider to 333/667 or 333/800
you can use 400/800 also as its a really loose setting and lets quads clock higher.

also the bios is supposed to let you use the Home button on your keybaord as a last known good boot setting incase the system doesnt want to boot, and
Insert as a Clear CMOS,
has anyone gotten those to work, i have never been able to make those work for me...
10-06-2008, 09:20 AM
ZoLKoRn

Some tried playing with QX9650 on it :)

Max FSB @485MHz http://valid.x86-secret.com/show_oc.php?id=428019
http://valid.x86-secret.com/ccpuz.ph...8019&nocache=1

Spi 1M@460fsb
http://img58.imageshack.us/img58/249...650jpgmwk8.jpg

Everest Mem-BW
http://img376.imageshack.us/img376/5...rqx9650ol3.jpg

Aquamark
http://img410.imageshack.us/img410/8...650jpgmns5.jpg
10-07-2008, 07:30 AM
ryboto

Quote:

Originally Posted by Lestat

stop running 4 sticks of ram for starters.
next stop going up in so little fsb steps.
just slam the fSB to 400 then 450, them after that with a quad its really hard, you need to do alot of tweaking.
set vcore accordingly. maybe +.250mv (just to try it, then lower or raise it if you need to)
Just to start with try these settings.
set Nb to 1.45 and CPU VTT to 1.33v (those are bios settings. the actual reading will be a little lower but thats ok)
All 3 GTL voltage settings just leave at .67x (just to get your system running.)

set ram divider to 333/667 or 333/800
you can use 400/800 also as its a really loose setting and lets quads clock higher.

I already returned the board. Also, I had been using the EXACT settings you're referring to. When I was testing, I only had 2 sticks installed, so it shouldn't have been a RAM limitation. I might have only been using 1.4v on the NB, but still, 375mhz should have given me a problem because it was too small a step up?
10-12-2008, 06:03 AM
mecho_gruh

DFI JR P45 T2RS x8

Hello I am new in the Xtreme Forum.
I've bought this mobo recently and I'm very happy with it. Q6600 G0 @3,2GHz at stock voltage and 3,6GHz at 1,4V 24/7. I've been using Matrox 4MB, and its time to move up to some 4870 CF or 4870x2 due to the limitted space between the cards. Is the x8 PCI-E slow for such cards? Have you made some tests between x16x16 and x8x8?
10-12-2008, 06:18 AM
Jamesrt2004

Quote:

Originally Posted by mecho_gruh

Hello I am new in the Xtreme Forum.
I've bought this mobo recently and I'm very happy with it. Q6600 G0 @3,2GHz at stock voltage and 3,6GHz at 1,4V 24/7. I've been using Matrox 4MB, and its time to move up to some 4870 CF or 4870x2 due to the limitted space between the cards. Is the x8 PCI-E slow for such cards? Have you made some tests between x16x16 and x8x8?

shouldn't be too bas to be honest as its pcie Gen2 so pcie 2 x8 = pcie 1 x16

so wont be too much of a hit if atall
10-21-2008, 04:23 AM
xixo_12

anyone use sunbeam core-contact freezer as cooling with this board?
how? can fit nicely?
10-21-2008, 04:30 AM
s e t h

thanks for those bios settings ZoLKoRn - i'll give them a try and see what i can get out of it
10-21-2008, 06:19 AM
ZoLKoRn

Quote:

Originally Posted by xixo_12

anyone use sunbeam core-contact freezer as cooling with this board?
how? can fit nicely?

Yep i tried too and meet problem same as you sure for can't install mounting kit :) but if you need to used it you should change top NB heatsink to TR-HR05 or Noctua NC-6 ;)

btw. i'll take photo for you later :)
10-21-2008, 08:15 AM
xixo_12

Quote:

Originally Posted by ZoLKoRn

Yep i tried too and meet problem same as you sure for can't install mounting kit :) but if you need to used it you should change top NB heatsink to TR-HR05 or Noctua NC-6 ;)

btw. i'll take photo for you later :)

i'm waiting for your picture, i just wonder it will fit or not, because currently i'm not own it, but in future i might grab one..

that mean with the caps at PWM are will not have any problem, so it's just NB height is the problem, am i right?:)
10-23-2008, 01:15 PM
ZoLKoRn

2 Attachment(s)

Well after i tried to install Core-Contact Freezer on JR-P45 after replace stock NB heatsink so it can't install same time for place to HR-05 or Noctua :( but if place to some zalman NB heatsink it work! and you can see from picture but it need some saw little fin about two row :D

btw. i think if change to HR-05 SLI it'll can install Core-Contact Freezer maybe :)
10-23-2008, 04:19 PM
xixo_12

Thanks man for the picture, look cool..:D
cutting the heatsink.. but it still work perfectly.:clap:
10-25-2008, 09:09 AM
Cornelious0_0

Thanks for the bios screens, I'm trying to hit 500x8 with my E8400/DFI Jr and was having some issues.

I'll give these settings a shot.
10-30-2008, 09:17 PM
panuza

oho!!!! ZoLKoRn ^^
11-05-2008, 06:37 PM
Praz

LP JR P45-T2R, E8600, 500x8, 2x2GB Memory 1000MHz, Post 1 of 3

DFI LP JR P45-T2R, 10/07 BIOS
500x8, Memory 1000MHz
E8600
2x2GB G.Skill F2-8000CL5-2GBPQ 1000MHz 5-5-5-15
SAPPHIRE 4870
OCZ Core SSD
Orange Slots Used For Memory

click for larger image
http://www.edgeofstability.com/image...ios/main_s.jpg http://www.edgeofstability.com/image...ios/volt_s.jpg

click for larger image
http://www.edgeofstability.com/image...os/dram1_s.jpg http://www.edgeofstability.com/image...os/dram2_s.jpg

click for larger image
http://www.edgeofstability.com/image...s/clock1_s.jpg http://www.edgeofstability.com/image...s/clock2_s.jpg

click for larger image
http://www.edgeofstability.com/image...os/phase_s.jpg http://www.edgeofstability.com/image.../feature_s.jpg

Code:

CPU Feature Page Thermal Management Control................Enabled PPM(EIST) Mode............................Enabled Limit CPUID MaxVal........................Disabled CIE Function..............................Auto Execute Disable Bit.......................Enabled Virtualization Technology.................Enabled Core Multi-Processing.....................Enabled Main BIOS Page Exist Setup Shutdown......................Mode 2 Shutdown after AC loss....................Enabled AC Shutdown free..........................Enabled O.C. Fail Retry Counter...................1 O.C. Fail CMOS Reload.....................Disabled CPU Clock Ratio........................... 8x CPU N/2 Ratio.............................Disabled CPU Clock.................................500 MHz Boot Up Clock.............................Auto CPU Clock Amplitude....................... 800mV CPU Clock0 Skew........................... 100ps CPU Clock0 Skew........................... 0ps DRAM Speed................................333/667 PCIE Clock................................100MHz CPU Spread Spectrum.......................Disabled PCIE Spread Spectrum......................Disabled Voltage Setting Page CPU VID Special Add.......................Auto DRAM Voltage Control......................1.908V SB Core/CPU PLL Voltage...................1.55V NB Core Voltage...........................1.3075 CPU VTT Voltage...........................1.10V VCore Droop Control.......................Disabled Clockgen Voltage Control..................3.45V CPU GTL 0/2 REF Volt......................0.67X CPU GTL 1/3 REF Volt......................0.67X North Bridge GTL REF Volt ................0.61X FSB Vref.................................. 2A DRAM Timing Page Enhance Data Transmitting.................Fast Enhance Addressing........................Fast T2 Dispatch...............................Auto Clock Setting Fine Delay..................Listed Below Flex Memory Mode..........................Auto CAS Latency Time (tCL)....................5 RAS# to CAS# Delay (tRCD).................5 RAS# Precharge (tRP)......................5 Precharge Delay (tRAS)....................15 All Precharge to Act......................5 REF to ACT Delay (tRFC)...................48 Performance Level.........................9 Read Delay Phase Adjust...................Listed Below MCH ODT Latency...........................Auto Write to PRE Delay (tWR)..................14 Rank Write to Read (tWTR).................11 ACT to ACT Delay (tRRD)...................3 Read to Write Delay (tRDWR)...............8 Ranks Write to Write (tWRWR)..............Auto Ranks Write to Read (tWRRD)...............Auto Read CAS# Precharge (tRTP)................3 ALL PRE to Refresh........................5 Read Delay Phase Adjust Page Channel 1 Phase 0 Pull-In.................Auto Channel 1 Phase 1 Pull-In.................Auto Channel 1 Phase 2 Pull-In.................Auto Channel 1 Phase 3 Pull-In.................Auto Channel 1 Phase 4 Pull-In.................Auto Channel 2 Phase 0 Pull-In.................Auto Channel 2 Phase 1 Pull-In.................Auto Channel 2 Phase 2 Pull-In.................Auto Channel 2 Phase 3 Pull-In.................Auto Channel 2 Phase 4 Pull-In.................Auto Clock Setting Fine Delay Page DLL and RCOMP Settings .................Auto Ch1 DRAM Default Skew.....................Model 3 Ch2 DRAM Default Skew.....................Model 3 RCOMP Setting.............................Model 1 Fine Delay Step Degree....................70ps Ch1 Clock Crossing Setting................Auto DIMM 1 Clock fine delay...................Current 2396ps DIMM 2 Clock fine delay...................Current 2396ps Ch 1 Control0 fine delay..................Current 268ps Ch 1 Control1 fine delay..................Current 268ps Ch 1 Control2 fine delay..................Current 268ps Ch 1 Control3 fine delay..................Current 268ps Ch 1 Command fine delay...................Current 394ps Ch2 Clock Crossing Setting................Auto DIMM 3 Clock fine delay...................Current 2066ps DIMM 4 Clock fine delay...................Current 2066ps Ch 2 Control0 fine delay..................Current 48ps Ch 2 Control1 fine delay..................Current 48ps Ch 2 Control2 fine delay..................Current 48ps Ch 2 Control3 fine delay..................Current 48ps Ch 2 Command fine delay...................Current 393ps Ch1Ch2 CommonClock Setting................Auto Ch1 RDCAS GNT-Chip Delay..................Auto Ch1 WRCAS GNT-Chip Delay..................Auto Ch1 Command to CS Delay...................Auto Ch2 RDCAS GNT-Chip Delay..................Auto Ch2 WRCAS GNT-Chip Delay..................Auto Ch2 Command to CS Delay...................Auto

click for larger image
http://www.edgeofstability.com/image...g_lin_64_s.jpg
11-05-2008, 06:39 PM
Praz

LP JR P45-T2R, E8600, 500x8, 2x2GB Memory 1000MHz, Post 2 of 3

XP SP3

click for larger image
http://www.edgeofstability.com/image..._occt_xp_s.jpg

click for larger image
http://www.edgeofstability.com/image..._3d06_xp_s.jpg

http://www.edgeofstability.com/image..._crysis_xp.jpg http://www.edgeofstability.com/image...00g_ut3_xp.jpg

3dx Max w/V-ray
Time to render: 14min 05sec

click for larger image
http://www.edgeofstability.com/image...chmark_680.jpg

click for larger image
http://www.edgeofstability.com/image...erest_xp_s.jpg
11-05-2008, 06:40 PM
Praz

LP JR P45-T2R, E8600, 500x8, 2x2GB Memory 1000MHz, Post 3 of 3

Vista 64 Bit SP1

click for larger image
http://www.edgeofstability.com/image..._occt_64_s.jpg

click for larger image
http://www.edgeofstability.com/image..._3d06_64_s.jpg

click for larger image
http://www.edgeofstability.com/image...3dvan_64_s.jpg

click for larger image
http://www.edgeofstability.com/image...pcvan_64_s.jpg

http://www.edgeofstability.com/image..._crysis_64.jpg http://www.edgeofstability.com/image...00g_ut3_64.jpg

3dx Max w/V-ray
Time to render: 15min 15sec

click for larger image
http://www.edgeofstability.com/image...chmark_680.jpg

click for larger image
http://www.edgeofstability.com/image...erest_64_s.jpg
11-05-2008, 11:20 PM
twwen2

Awesome Praz!

I didn't have much luck over 440FSB on my JR, so i'll give these settings a shot. :up:
11-06-2008, 03:27 AM
jcool

Try lowering GTLs if you run into trouble early on. The E8400 I put in there didn't like 445*9 at first, but when I set GTLs to 0,63x instead of 0,67x while leaving the VTT at 1,1V it worked like a charm. Also running 2x2GB@1066 with only 1,34V NB set in bios.
I really like the board, just 1 issue: You MUST disable EIST (speedstep) it's buggered.. if you enable it, the DFI will substantially raise the Vcore if loaded (like 1,2V bios setting, load >1,3V). Really annoying.
11-06-2008, 03:36 AM
emoners

@ZoLKoRn: try using the Xigmatek Porter, maybe it will work.

@Praz: thanks for the bios settings! :up:
11-06-2008, 04:41 AM
Praz

Quote:

Originally Posted by twwen2

Awesome Praz!

I didn't have much luck over 440FSB on my JR, so i'll give these settings a shot. :up:

Good luck. Hope the settings are of some help.

Quote:

Originally Posted by jcool

You MUST disable EIST (speedstep) it's buggered.. if you enable it, the DFI will substantially raise the Vcore if loaded (like 1,2V bios setting, load >1,3V). Really annoying.

As the screenshots show I had no issue with SpeedStep.

Quote:

Originally Posted by emoners

@Praz: thanks for the bios settings! :up:

You're welcome.
11-06-2008, 05:04 AM
jcool

I tried with 2 CPUs, E8400 E0 and E7300 M0. Both showed the same strange behaviour (load Vcore 0,1-0,15V above bios setting!) with EIST enabled. C1E enabled gives no problems.
Bios used was shipping bios, which seemed to be newer than the one offered on DFis own website. After I flashed to the bios on the DFI page, the Vdroop control feature was gone, so I re-flashed the other bios (09 something).

Show 100 post(s) from this thread on one page