yeah looks like ima have to solder one to
Printable View
yeah looks like ima have to solder one to
anyone can give me VMHC mod??? i need more than +0.7v :D
Johnny would prolly be the best candidate for that as he is the vmod guru round here. I'm trying to find a vdram mod myself. but it's a definate pita
anyone have the actual resistors for the vcore mod or pics of the vcore mod? seriously .5 jumps are a little rediculouse and on a wolfdale that could be thediff between the safe zone and non safe zone for water and air cooling.
Still no vcore mod???
philbrown23, measure resistance FB->GND and multiply it with 20x, so You now which VR to use ;) I'll do the mod in next few days and report back.
sweet!
looks like I need to get my soldering iron out... LN2 on the tpower soon for me...
I am also very interested in the vMCH mod if there is one.
I am reading 2.17k on that resistor for the pencil mod. why is it different? what should I pencil it down to?Quote:
Originally Posted by philbrown23
well yeah pencil it down worst case scenario you'll have to erase it.Quote:
Originally Posted by DiscoTech
Ceemic you get the mod done yet? when I X the measurement by 20 I get 56kohms so looks like a 100kohm resistor
philbrown23, if so, I'd recommend 50k VR. It has "smoother" end. You need to adjust 100k too far and can't adjust Vcore so well...
I haven't had time yet (yesterday I moded a HD4850); probably I'll do it on Friday and report ASAP.
Can someone confirm that Vcore mod?
http://www012.upp.so-net.ne.jp/ohij2/vcore-mod.jpg
I can't atm look, which PWM pin it's connected with.
philbrown23, maybe You have time to do the quick measurement? I'd like to know the resistance from that point to GND. Thanks!
Macro from that place: http://ceemic.pri.ee/hardware/tpower/tpower20.JPG
measurement from that point to ground= 44.6kohms I think it'd connected to the same pwn but iunno
EDIT: I CAN confirm that pencil mod, it actually works better than the other one in the beggining of this thread, before I still had .1 vdroop now I have a mere .003 vdroop ;)
~45kohm? Have You disconnected all stuff, including CPU, from board?
This resistance should be around 5-10kohm, so 50-100k VR would work.
well I mis typed the resistance was 4.46kohm not 44.6 rofl, I was in a hurry, cuz I had to head to work. but yeah just under 5kohm
Then 50k should work. Is that point directly connected to FB pin or which?
Quote:
Originally Posted by ceemic
yeah I'm pretty sure it is, not 100% but pretty sure. I'm still kinda new to this hard modding stuff.
Quote:
Originally Posted by philbrown23
Quote:
Originally Posted by ceemic
Are these the pencil vdroop mods you are talking about? So the top recent one works better?Quote:
Originally Posted by Pt1t
Do you pencil both of those resistors shown? do you know the values to aim for?
Is there a vcore pencil mod?
Thanks.
DiscoTech, I'm talking about hard-mod. I don't ever use pencil mods ;)
Not trying it thread-jack but anyone have measure points for this board? Vcore, VTT and Vmch most importantly
Thanks
if you read up a few posts you'll see the measure point ;)Quote:
Originally Posted by Deux
Deux, Vcore - otherside mobo: coil legs nearest to socket ;)
http://www012.upp.so-net.ne.jp/ohij2/vcore-mod.jpg
http://www012.upp.so-net.ne.jp/ohij2/vnb-mod.jpg
http://www012.upp.so-net.ne.jp/ohij2/bio-vddr-mod.jpg
http://www012.upp.so-net.ne.jp/ohij2/vfsb-mod.jpg
http://www012.upp.so-net.ne.jp/ohij2/vfsb-measure.jpg
Appreciate it :)Quote:
Originally Posted by ceemic
well CEEMIC I tryed that hardmod and I got no post no matter how low I set the resistor. I may have done it wrong but I dont think so. your still welcom to try it as you seem to be better at hardmods than me.:welcome:Quote:
Originally Posted by ceemic