MBM on P5B Dlx !!! Well almost, still need some help

Quote:

---

Originally Posted by Millyons

updated data files.....

i had to make couple changes to make it work right with FCG core temp plugin





ps: if anyone has a modular PSU cha you check if the +5v rail is the right one, im not too sure about that one

---

Is this the latest version of the config file?

Also Big.Wayne: which sensor did you use for SATA Port 0 and 1?

thanks

the one from here
http://www.xtremesystems.org/forums/...6&postcount=17

I've just built my 1st conroe rig, coming from AMD. I'm a graet fan of mbm & appreciate the great work Millyons, freecableguy & every1 is doing to bring it to this platform.

I've followed the following :-
1) Install MBM - mbm5370.exe
2) Install MBM5370_3 Patch
3) Install coretemp_mbm5plugin_winxp_11 - see readme for more info.
4) Install P5B Dlx config copy files to Data Dir.
5) Set Up:-
Vcore v Change to SB(Sata)V
+12v Change to SB Vcore v
??? Change to FSB Termination Volts
+3.33 change to +5v
Temps
Sensor 24 to Core1
Sensor 23 to Core2

Checking mbm to Asus Probe2 :-
http://homepages.nildram.co.uk/~chsm...s_Probe2_1.PNG
Good News:D
Have identified 3 new voltages :-
Southbridge Vcore
Southbridge Sata
& FSB termination volts
Bad News:rolleyes:
Lost
12v
3.3v
vcore
VDimm

The bottom part of the MBM Dashboard shows the unknown sensors.
Any help with finding the missing values greatly appreciated:D

Quote:

---

Originally Posted by Supershanks

Good News:D
Have identified 3 new voltages :-
Southbridge Vcore
Southbridge Sata
& FSB termination volts
Bad News:rolleyes:
Lost
12v
3.3v
vcore
VDimm

---

Hi Supershanks,

that looks promising, how did you find the new sensors? I don't believe I even have vDimm myself at the moment? that would be cool as would the others. I wouldn't wanna lose vCore though!

Big.Wayne: which sensor did you use for SATA Port 0 and 1?
thx

Quote:

---

Originally Posted by Stx

Big.Wayne: which sensor did you use for SATA Port 0 and 1?
thx

---

Hi Stx, I went 'General' settings > scrolled down and checked the two boxes next to hard drives, then apply, exit, restart. Then when you boot up again, launch MBM and go to temps and do the drop down box, you should see the actual hard-drive sensors appear. Hope this helps! :)

http://img474.imageshack.us/img474/1508/mbmdisksfc8.jpg

^ thanks for that, works fine

@Big.Wayne

Quote:

---

that looks promising, how did you find the new sensors?

---

Must admit it was more by accident than design :D.
I just did as i said in my earlier post & thern noticed that the vcore & ??? where the same values as asus probe.

Quote:

---

Vcore v Change to SB(Sata)V
+12v Change to SB Vcore v
??? Change to FSB Termination Volts

---

I have the Winbond W83627DHG chip Think there must be some info in the voltage 8~16 sensors but all i'm getting are zeros. Looking at the Voltage.ini
LM78 is configured fot std, epox & tekram, these seem to cover the 1st 7 voltage sensors, so iwhat is set up for sensors 8~16??, does the voltage.ini need editing i wonder??