Looking for "Fatbody" D9DQW 1GB stick dumps.

Printable View

Show 100 post(s) from this thread on one page

12-26-2006, 09:56 AM
heikis

Quote:

Originally Posted by The Stilt

Finally I found some time to write a custom SPD for you guys.

If your modules match these specs, you are good to go:

Type: DDR-II SDRAM
Capacity: 1024MB
Configuration: 64M x 8
Ranks / Banks: 2 (Double sided)
Data Width: 64

Frequency / Timing Table

DDR-533MHz @ 3-3-3-10-15 (tCL-tRP-tRCD-tRAS-tRC)
DDR-667MHz @ 4-4-4-13-19 (tCL-tRP-tRCD-tRAS-tRC)
DDR-800MHz @ 5-4-4-15-22 (tCL-tRP-tRCD-tRAS-tRC)

Target IC

D9DQT, D9DQW, D9DRD, D9DQZ, D9DQR, D9DQP

Click here to download.

Load it to Thaiphoon Burner and fully rewrite the desired sticks with this SPD file.

http://www.armada.fi/Rhino/Rhino_Cus...body_CPU-Z.jpg

does your custom SPD give any other advatnages than just tighter and higher memory settings? i mean the same things i can do just confuguring my mem settings in bios?
12-28-2006, 03:42 AM
skootyloops

Quote:

Originally Posted by heikis

does your custom SPD give any other advatnages than just tighter and higher memory settings? i mean the same things i can do just confuguring my mem settings in bios?

I think its more used for when your motherboard supports a minimum speed of PC4200 yet your rams default speed is PC3200

This way after flashing them it will work to the required speeds :)

The Stilt, is there any chance you could make some 512mb versions of those? I'm getting some ram in tomorrow which has a slight error that the spd file is screwed and calls the ram PC3600.

Im 99% certain they are D9DQT. I will check when I get them, but they are the OCZ PC4200 EB Rev 2 which is meant to be that :D
12-30-2006, 09:17 AM
irev210

Here, if you are still having problems, try mine-

This is for 1 gig sticks ONLY!

Enjoy, nice easy timings of 4-4-4-12 @ 533

Fatbody spd link
12-30-2006, 11:19 PM
geforce man

asus boards dont boot these sticks for the reason of they are shorting in the dimm slots, they need to be opened up a bit, i think dino's had a guide showing this. It only affects Asus, and ASrock boards (my asrock needed it to be done) basically, the gist of it is you have to put the sticks in, then open the tabs up on both sides SLIGHTLY, and boot. no problems :)
01-03-2007, 04:12 AM
skootyloops

Quote:

Originally Posted by geforce man

asus boards dont boot these sticks for the reason of they are shorting in the dimm slots, they need to be opened up a bit, i think dino's had a guide showing this. It only affects Asus, and ASrock boards (my asrock needed it to be done) basically, the gist of it is you have to put the sticks in, then open the tabs up on both sides SLIGHTLY, and boot. no problems :)

Here is the picture stolen from Dinos22's thread on OCAU

Quote:

Originally Posted by Dinos22

http://img89.imageshack.us/img89/4456/trickau6.jpg

Hope that helps people :)
01-03-2007, 04:24 AM
dinos22

Quote:

Originally Posted by skootyloops

Here is the picture stolen from Dinos22's thread on OCAU

Hope that helps people :)

thief :p: hehehe

pls be careful with that people....i don't want anyone killing any RAM because of my little suggestion there hehe
02-03-2007, 05:33 PM
INFECTED

Hi guys,
I too have bought a couple of these 1gb D9DQW and I've flashed TheStilt's SPD on them succesfully, but is it useless right? I mean to change SPD, timings etc cause they don't boot on Asus boards the same, isn't it?
Then I'd like to know from TheStilt which SPD he used and then modified to have final SPD "Rhino Custom Fatbody 1GB"
Tnx :)
02-03-2007, 05:39 PM
alexio

Quote:

Originally Posted by INFECTED

Hi guys,
I too have bought a couple of these 1gb D9DQW and I've flashed TheStilt's SPD on them succesfully, but is it useless right? I mean to change SPD, timings etc cause they don't boot on Asus boards the same, isn't it?
Then I'd like to know from TheStilt which SPD he used and then modified to have final SPD "Rhino Custom Fatbody 1GB"
Tnx :)

http://img89.imageshack.us/img89/4456/trickau6.jpg

2 posts up :rolleyes:
02-03-2007, 05:45 PM
INFECTED

Quote:

Originally Posted by alexio

http://img89.imageshack.us/img89/4456/trickau6.jpg
2 posts up :rolleyes:

Yes, I've read whole thread and that post too but I'm not sure this tweak works on all Asus and Asrock boards, for this reason I asked to know if anyone had found another 100% working alternative solution... ;)
02-03-2007, 06:02 PM
alexio

Quote:

Originally Posted by INFECTED

Yes, I've read whole thread and that post too but I'm not sure this tweak works on all Asus and Asrock boards, for this reason I asked to know if anyone had found another 100% working alternative solution... ;)

It works on all boards. Micron original DDR2 dimms have too short gold pins and the picture shows how to fix this. It's not a compatibility issue on the technical level. All Micron DDR2 ICs are perfectly compatible with DDR2 Asus motherboards.
02-05-2007, 09:53 AM
INFECTED

Quote:

Originally Posted by alexio

It works on all boards. Micron original DDR2 dimms have too short gold pins and the picture shows how to fix this. It's not a compatibility issue on the technical level. All Micron DDR2 ICs are perfectly compatible with DDR2 Asus motherboards.

Thanks Alexio ;)
I thought there was some kind of technical incompatibility...
02-17-2007, 02:19 PM
heikis

Quote:

Originally Posted by irev210

Here, if you are still having problems, try mine-

This is for 1 gig sticks ONLY!

Enjoy, nice easy timings of 4-4-4-12 @ 533

Fatbody spd link

this works well on d9dqw 1gb sticks?

Show 100 post(s) from this thread on one page