Asus P5B Vanilla (non dlx!) vcore+dimm needed

Printable View

Show 100 post(s) from this thread on one page

09-17-2006, 07:20 AM
remorema

Quote:

Originally Posted by Thallid

I tried, but I'm not really sure about the measuring points :confused:

Anyway, this is what I came up with, if this is wrong, I'll try again:
http://img205.imageshack.us/img205/5812/namnlosea6.jpg

tkx mate.

if you have some doubts i can help you out in MSN.

remorema(at)gmail(dot)com
09-18-2006, 06:59 AM
wittekakker

Report back: Vdimm worked for me too, thanks to you Persivore.
09-18-2006, 07:52 AM
LenniZ

Okey, so I have decided to order some VR's and get this board vcore modded (by me).

So, if I understand right it should be like this:
Point -> 100k VR -> Ground ?
09-18-2006, 08:00 AM
Pyr0

Thallid, the red line is right, but the blue line needs to measure the resistance from that leg to the opposite side of the little SMD capacitor :up:
09-18-2006, 08:54 AM
remorema

Quote:

Originally Posted by LenniZ

Okey, so I have decided to order some VR's and get this board vcore modded (by me).

So, if I understand right it should be like this:
Point -> 100k VR -> Ground ?

50k is fine for the job.

i did mine with a 50k and it works like a charm.

to bad that droops 0.04 under dual orthos.

Quote:

Originally Posted by Pyr0

Thallid, the red line is right, but the blue line needs to measure the resistance from that leg to the opposite side of the little SMD capacitor :up:

tkx mate.

i tought persivore was talking about the capacitors around the cpu chip.

lets see if we can make this work. :toast:
09-18-2006, 09:18 AM
LenniZ

Did you gain any better results after the vcore mod?
09-18-2006, 09:25 AM
wittekakker

For Vdimm I took a 10k VR. Around 10k regulating the Vdimm goes very slowly. 20k should take even longer, so I think it's better to stick with 10k VR for Vdimm. With a 10k resistor Vdimm is less then 0,1 above Bios setting, should be no problem.

Been testing my Mushkins up to 2,5V, there seem to be no problems.
09-18-2006, 09:28 AM
remorema

Quote:

Originally Posted by LenniZ

Did you gain any better results after the vcore mod?

before the mod i wasn't able to hit 3.8ghz on my allendale 6400, because max vcore on bios only gave-me 1.53, wich wasn't enough to clock the chip at that speed. i need 1.575 to boot to windows with that clocks.
09-18-2006, 09:45 AM
LenniZ

Sounds very good, ordering some 50k VR's right away.
09-18-2006, 12:23 PM
wittekakker

Persivore,

what about this FET controlling the MCH voltage.
http://home.scarlet.be/wittekakker/P5Bmods/vmch.jpg
09-19-2006, 01:09 PM
wittekakker

Persivore,

Or could Vmch be this one?
http://home.scarlet.be/wittekakker/P5Bmods/vmch2.jpg

Here are my Vdroop measurements:
[OLD PICTURE DELETED]
09-19-2006, 01:20 PM
persivore

1 Attachment(s)

Can you do the same with the 2 capacitors I've circled. It looks like they might be connected between the 2 pins from the photo.

For the Vmch mod, could someone try to get a high res picture of the entire board.
09-19-2006, 01:23 PM
wittekakker

I'll continue my research tomorrow, thanks for having a look at it allready.
Good night ;)
09-20-2006, 06:40 AM
wittekakker

Persivore,

It seems I've made a mistake yesterday. The restistor was not connected to Pin16 but to Pin15. My better method of measuring proved that today.
My new measurements:
http://home.scarlet.be/wittekakker/P5Bmods/vdroop.jpg

R is just how I named them. It's not ment to point out that they are Resistors or Capacitors or whatever.

For pictures of the mobo look here:
Mobo full: http://home.scarlet.be/wittekakker/P5Bmods/IMG_1437.JPG
Mobo south: http://home.scarlet.be/wittekakker/P5Bmods/IMG_1445.JPG
Mobo north: http://home.scarlet.be/wittekakker/P5Bmods/IMG_1446.JPG

Chip ID's are not very clear, my digicam is a cheap one. Just ask when you need to know a chip ID.
09-20-2006, 07:18 AM
remorema

Quote:

Originally Posted by wittekakker

Persivore,

It seems I've made a mistake yesterday. The restistor was not connected to Pin16 but to Pin15. My better method of measuring proved that today.
My new measurements:
http://home.scarlet.be/wittekakker/P5Bmods/vdroop.jpg

R is just how I named them. It's not ment to point out that they are Resistors or Capacitors or whatever.

For pictures of the mobo look here:
Mobo full: http://home.scarlet.be/wittekakker/P5Bmods/IMG_1437.JPG
Mobo south: http://home.scarlet.be/wittekakker/P5Bmods/IMG_1445.JPG
Mobo north: http://home.scarlet.be/wittekakker/P5Bmods/IMG_1446.JPG

Chip ID's are not very clear, my digicam is a cheap one. Just ask when you need to know a chip ID.

tkx mate, you really doing a nice job. lets wait for persivore, and see if he can pull this off.
09-20-2006, 07:32 AM
wittekakker

This is how it should be in the datasheet:
http://home.scarlet.be/wittekakker/P5Bmods/sheet.jpg
09-20-2006, 07:42 AM
persivore

For the Vdroop mod, connect a 50k variable resistor accross either 'R2' or 'R3'. Decrease resistance to decrease droop.
09-20-2006, 08:03 AM
wittekakker

After the last pictures I posted I thought you were going to post that. Have to go eat and do some stuff, I'll report back within 2 hours.

Thx Persi
09-20-2006, 08:20 AM
remorema

Quote:

Originally Posted by persivore

For the Vdroop mod, connect a 50k variable resistor accross either 'R2' or 'R3'. Decrease resistance to decrease droop.

excuse me for my bad english. when you mean across, does it mean this ??

http://img150.imageshack.us/img150/4345/vdroopul1.jpg
09-20-2006, 09:01 AM
persivore

Quote:

Originally Posted by remorema

excuse me for my bad english. when you mean across, does it mean this ??

http://img150.imageshack.us/img150/4345/vdroopul1.jpg

yea, thats fine :)
09-20-2006, 09:06 AM
remorema

Quote:

Originally Posted by persivore

yea, thats fine :)

tkx mate. :toast:
09-20-2006, 12:12 PM
wittekakker

Got a little retarded. I solderded that 50k VR.
Now, when I set in BIOS 1.6V, I get idle 1,6V, and loaded 1,6V. The weird thing is that I did not had to turn the VR, it's sitting @ 50k. When I turn the pot it get's up 0.01V, didn't try further. I don't know if I had any problems with Vdroop in the past, I didn't really meassure Vcore on my board then.
I think I'm going to replace that VR with a normal resistor.

SO... it works with me, can others try it also and report back how this mod worked for them.

Big kiss for our Vmod mod :)
09-20-2006, 12:49 PM
remorema

Quote:

Originally Posted by wittekakker

Got a little retarded. I solderded that 50k VR.
Now, when I set in BIOS 1.6V, I get idle 1,6V, and loaded 1,6V. The weird thing is that I did not had to turn the VR, it's sitting @ 50k. When I turn the pot it get's up 0.01V, didn't try further. I don't know if I had any problems with Vdroop in the past, I didn't really meassure Vcore on my board then.
I think I'm going to replace that VR with a normal resistor.

SO... it works with me, can others try it also and report back how this mod worked for them.

Big kiss for our Vmod mod :)

did you did it the way i marked it on the picture ??

please post how you did it.

i'll do mime tomorow and report ASAP.
09-20-2006, 12:52 PM
wittekakker

Yes, just like that.
09-20-2006, 12:55 PM
remorema

Quote:

Originally Posted by wittekakker

Yes, just like that.

and i tought that i was going to take a lot of time in order to tune the POT.

if it is like you say so, its pretty simple :D

Show 100 post(s) from this thread on one page