Download the newer version of the program from ABIT's website... It let it up to 600mhz :rolleyes:
Printable View
Download the newer version of the program from ABIT's website... It let it up to 600mhz :rolleyes:
Just curious what the VR should be set at before start up so as not to fry anything?:eek:Quote:
Originally Posted by crotale
I'm mostly interested in the vmch mod. And if anyone knows, is the lack of vmch over 1.45v in bios a hardware limit or does abit just not want to allow anymore vmch on the AB9?
Thanks
Maximum resistance to begin with (100k).
Thanks
How much Vdimm can I get with this MOD?
And how should I set Vmch to set the voltage in the VR
Tanx
(sorry for my bad english)
any vdroop mod?
Nice vmods Crotale and Johny Brafo.
Vdroop mod would be nice, vcore read point to. I dont know if i can trust the readings from Uguru.
uGuru reads it pretty well, and my board doesn't need a droop mod in my opinion.Quote:
Originally Posted by ownage
The coils are insulated at the front, so the best way would be to solder a read out cable from the backside of the board.
http://www.nordiccrew.com/crotale/ab...e_read_out.jpg
no vdroop mod crotale??
As I wrote in my post above, I don't see the need for a droop mod.
How much does your board droop?
Normally AB9 has about 0,05v vdroop as p5b-dlx..
Max bench before vmch mod was 463fsb,just tested a little after the vmch mod,but big improvement :banana:
Got to install a new cpu and nb waterblock,then i will test for max fsb :D
Thanks alot guys :clap:
http://i94.photobucket.com/albums/l9...th_Abit002.jpg
http://i94.photobucket.com/albums/l9.../th_475fsb.jpg
463FSb just benchable right? I could only run spi 1m on 463fsb.Quote:
Originally Posted by Norz
What cooling did you use when hittings 475fsb and how stable whas it, 24/7 stable or benchable stable?
At 463fsb i did run Superpi 1M,32M 3DMark 01,03,05,06 Aquamark 03,just about every Bench i want,that was with stock nbcooler,only a extra 7cm fan on top of it. The cpu was cooled by a old Swiftech,but it has been replaced with a AC Cuplex XT,and tomorrow im goona fit a EK Wave on the cpu..lol..Quote:
Originally Posted by ownage
I have done the vmch mod and its looking grate,but i have to fit my old AC nb watercooler before i test moore,its hot mate :p: and 475fsb was just to show that there is moore to come :D
And hitting 475fsb was with the same setup,watercooled cpu,aircooled nb,stability on 475 i dont know,just my first test and i was just taking a screenshot and shut her down,dont wanna kill her before i put on the watercooler.
Heres a few pics from 463fsb benching with my E6300 and Msi 7900GTO
http://i94.photobucket.com/albums/l9...7900GTOGTX.jpg
http://i94.photobucket.com/albums/l9...E630032Ghz.jpg
No pencil mod is available yet? :(
I know it's not accurate, but it's not bad after my experience with p5b-dlx.. And more easy than soldering.. :)
@ownage,you wanna see moore :D
http://i94.photobucket.com/albums/l9...480vmch162.jpg
Just open the window in my room,+5`c outside. Now i wait for the waterblock,there is moore left,my goal is 500fsb :woot:
As promised,500fsb
Do not ask if its stable,just tested her with the nb waterblock.
Now i will find max for the hole sh##.:clap:
http://i94.photobucket.com/albums/l9...00fsbfinal.jpg
Nice results Norz, congratz.
Now if only Abit would raise the bios vmch limit :D
@ownage,hey man,you are currently in the extreme vmod forum :DQuote:
Originally Posted by ownage
Pick up that iron and solder mate :D
...man,she just wont stop overclock :banana: :banana:
Running orthos,superpi 1M.... :clap:
Just wanna say thank you :D
http://i94.photobucket.com/albums/l9..._3500valid.jpg
@crotale
my board vdroop about 0,4~0,6 when full load..
do you think it need vdroop mod?coz that droop is so annoying,
You mean 0.04-0.06v right?Quote:
Originally Posted by kutujambak
1.325v (stock) - 0.4 = 0.925v and I'm not really sure the CPU would manage.
Where do you measure vcore?
Good work Norz!
ups sorry,,:D:D ur right 0,04~0,06v
i measure it from vcore read out on shown by ur post #33
Crotale, I saw that you changed the mod a little, but can I stay using the old scheme?
And another question is: I watercool ma NB, but temps here in brazil are very high, and the ND keeps @ 33°C... How much FSB should I get with this temps, and how much voltage I can set safely?
Tanks alot!
Sorry for my bad english
Got myself some D9###,wanna do the vdimm mod also again,but where is read out on vdimm? ...have i been missing something....
----cheers----