look more carefully ;]
there is a jumper there ;]
but its soldered do the PCB ... just check it out ..
im sure that there is a connection between 4th leg of regulator and this "new jumper"
its large place to solder .. so its also easy ...
its the same PCB as the "new" one ..
galaxy just cuts the cost of the cards. They took away jumpers for voltage (useless any way .. 0.05 increse) and bios change. Theres also no buzzer (but i never used him and never heard a sound from it :P ) ...
p.s: when making vgpu mod you can solder to a jumper that changes voltage of the card (the yellow one) ... no soldering on the card needed ..
middle pin is connected to 4th leg od the controler
the yellow it ground?
can use for vgpu and vmem?
Kind of a lame but i wanned to ask how can i do that delta thingy on my VGA?
I just did a pencil mod on R451 and it wokred lika a charm running on a 720MHz core but havent mesured the resistence and voltaje but a little more then 729 got a crush(in the first mod i was able to run a 750MHz and more but card was too hot(GPU 96c 1min Load) soo i did the mod again from the start). Now most of the time its runing Idle-56c and load-85c with a sink on the Vgpu mossfet and the stock cooling... a 93c Load in NFS MW but its only there i think most of the time the temps are like i sad before.
http://www.nvworld.ru/downloads/BIOSModifier_33.zip
Here it is, my friend. Go out and play :) .
I tried it a while ago, but didn't make any difference (had driver problems <- this is lame :p: ). Try something like 70-90 delta. Here's a start - in the attachment. Just remove the .zip. BEWARE - THE FANSPEEDS ARE SET TO 0% !!! Change them!
I'm gonna test it these days too.
Успех, братле.
delta must be a negative number (i mean below ZERO)
i use almost the max value .. -125 :) :D
and afaik its only for gf 7xxx series
Nice of you to add this info. :)Quote:
Originally Posted by Chaos-PL
Ok thats cool! ;) im gonna try it tomorrow after work, im working at night :(
Just woundering will the use of a delta help me OC more, my max now is 729Core and can i use a third party overclocking tools like RivaTuner or ATiTool and still have the delta or it has to be no change at all after the flash like a registry tweak in the driver ?!
The delata is permanent. It's written in the card's bios. So you overclock the GPU and the delta is aways the same MHz less. Are you cooling the card with a Zalman?
Nop im cooling it with the referent cooler Full load - 89C and Idle - 56C.
OK i got the point ;) Flashed my vga but dident liked the artefacts soo im not using deltas for now ;).
got the 7600GS Xpertvision/Palit
here for example is the 7600GT Backside. it looks like mine but i doesn't have the GT version:
http://www.ixbt.com/video2/images/pa...-scan-back.jpg
my question is, what voltage mods are working with my card and which do not? :(
the attached file"delta.rom.zip" is corrupted ;\ (can't open the file)
Anyway, i've got the "old" pcb 7600gs with 1.2 ns and Zalman changed to VF700Al-Cu @5V , without any mods (well only changed the yellow jumper + 10mhz on the core ;] ) Core @ 630Mhz and DDR3@ 1700Mhz ( 2x850Mhz) rock stable, now the core is undervolted ;] need either a bios volt mod or hard v-mod.
my vga :
http://img205.imageshack.us/img205/9...0666ht7.th.jpg
:cool:
also board rev. p456h1
hello there,
I have a 7600GT Z which looks like the galaxy with the 3 jumpers and board rev p456h1 which overclocks to 650/1515 without mods. I volt mod the bios using nibitor but did not work but I leave it cos I changed the default speed to 620/1460 in 3D and fan speed to 100%. I changed the volts jumper position and gained 10 MHZ overclock using my modified bios (haven't tried the jumper with original bios, shall I?).
I am a bit dissapointed with the memory speed (max 1515. Any way to increase the speed with a pencil mod?
thanks
got the 7600GS Xpertvision/Palit
here are two links, the first one is probably the one i got. the second one is the sonic edition, but i don`t think, that i got that one...
the third picture is how my cards looking like.
http://www.palit.com.tw/en/products/nv_pcie_7600GS.html
http://www.palit.com.tw/en/products/...00GS-Sonic.htm
http://www.palit.com.tw/en/products/...c_nv7600GS.jpg
so, my question, is this refference or non-refference?
and: what voltage mods are working with my card and which do not?
my best guess is that this card is non "standard" layout or to be exact alternated reference layout :|Quote:
Originally Posted by ProfNuke
How much ohm is resistor on v-mod for 7600gs 256mb ddr3?Thanks,sorry for bad english
You are wrong..Quote:
Originally Posted by Bl4ck^!
You have NEW PCB .. not old
@Filip
50ohm
basicly it's the "new old" design, it has jumpers and "old" Zalman VF700Al, so it's "old" ;] (there are 3 layouts now so mine 2nd is old now ;F)Quote:
Originally Posted by Chaos-PL
Quote:
Originally Posted by Bl4ck^!
naaahh ..
we are talking about PCB .. "newest" pcb is the same as the "new" but it doesn't have jumpers .. but pcb's are the same..
I have new revision,without jumper.Yellow jumper(actually there isnīt jumper) is connected to 1-2(solder),can i just connect with 3,or i must disconected first conection and connect 2-3.You know what i mean?
Sorry for bad english :)
Hey there is this topic alive ?:)
I just wanna ask whats the rezistance of ur vmem rezistor after pencil mod with which u can make 1800MHz stable, here it is an site of mine with the pencil mods for that carb but im having trouble clocking my mems, but other people say they are doing 900MHz DDR or eaven more !
www.pencilmod.hit.bg