I updated @ startpost :)
Printable View
I updated @ startpost :)
if someone could send me a dump for a pc2100 bh-75 stick, i would greatly appreciate it. please pm me letting me know that you posted it though, chances are that i won't notice it here.
You could write the SPD from a PC2700 BH-6 stick, i'm sure it could take it. After all, BH-7.5, BH-6 and BH-5 are the same stuff differently rated.
And some more dumps :)
Quote:
Originally Posted by omga14
Old Winbond BH5 = 0.175µm
New Infineon/UTT BH5 = 0.15µm
U have done something wrong ;)Quote:
Originally Posted by Waus-mod
My Mushkin Special 2-2-2 BH6 are 512 MB Sticks!
U have listed them under 256 MB Sticks :D
All edited/changed!
There is something wrong with OCZ PC3200 Gold (new BH) dump.
SPD says model number ocz4001024DCGE and timings 2.5-3-3-7. But there is no such model and there should not be such SPD timings if RAM has BH chips.
Could the author of this dump specify what model number is it? It could be OCZ Gold EL but default spd should be 2-2-2 or smth like that.
It's correct, the 3200 Gold with new BH-5 is rated 2-2-2-5 at 2.8V, so 2.5-3-3-7 is written in the SPD to make it able to boot and work at 2.6V, what most mobos default to. Check here, RyderOCZ explains it:
Quote:
As Nuke says..the SPD (what the motherboard reads off the ram to set timings when things are at auto) is set "looser" so that all motherboard will boot with the ram installed the first time.
Manually set the bios to 2-2-2-5 timings (CAS-tRCD-tRP-tRAS) and 2.8-2.85V for the ram and things should be peachy.
OK thanks, that is a bit strange though because I have OCZ gold EL and SPD timings are 2.5-2-2-7. I bought them used, who knows maybe previous owner rewrote it?
Waus-mod:
I linked my dump to a site that is kind of unstable, so here is the same dump but attached to XS...(didnt know I could attache files this way :D)
just to be sure it will stay here forever ;)
only edit the link on the first post and its all good.
I've managed to get this spd reflash to achieve alot more than just repair RAM :) I was sold two "matched" sticked of BH-5 but it turns out are different sticks of Corsair RAM. P4GD1 refused to boot at 1:1 ratio fro some reason so reflashed both sticks with the Mushkin Level II Black 3500 dump. Result, first try 273MHz @ 2-2-2-4 timings ! I may play about and see which of the dumps performs best with my sticks :D Anyone any recomendations, what information is stored in the spds, is it just the timings for various bus speeds or is there more?
Yes this tool is just amazing ;) I have done some "editing" to my Infineon 6-A sticks, and this way the never ever again will detected as poor DDR333 with 2,5/3/3/7 from my Board ;) U can have a lot of fun with this tool.
Will try some other settings too :D
If you load dump and then press F12 you will see what information is stored. The main problem with 2 different sticks is that main timings and/or subtimings are not similar. If you flash same SPD then basically it should solve timings problem.
Thank you very much. My G.skill TCCD works again. :banana:
Hello, I am new to these forums, I referred to this post by someone at DFI Street for help with some performance loss on my OCZ sticsk. I searched this post and was unable to find dump info for my Memory, perhaps someone could help?
I am running OCZ El Rev 2 Platinum (2 * 512) sticks in a DFI based 939 system. Do any of you have the dump info for these sticks?
Thank you.
heh.
it's becoming Memory BIOS Section :D
maybe someone wise could "mod" some of these spd's?? ;)
Does anyone have a dump for a 256Mb stick of Mushkin Level II PC3500 (old bh5, with pink heatspreaders)?
Thanks!
Way ahead of you mate, but it doesn't help too much :)Quote:
Originally Posted by myrddin669
Check it out.
Mansquatch, i used the SPD off of my better performing stick and wrote that to the other. i was having a performance issue with the 2 sticks in together and this helped me get back on track. maybe this will help you regain your performance if the 2 sticks have the exact SPD written. it's something you could try until someone could post a dump for you ram here.
Nope i dont have on, and on the first page of this Topic there is only a 512 SPD Dumpfile.Quote:
Originally Posted by Ratax
BUT ;) I have edited the 512MB Dumpfile to become a 256MB Dump file. Very izi and normaly the SPD files shouldnt differ cause thee 512/256 Infineon 6-A dumpfiles dont differ in any way, too. Checked some 512/256 Dumps of same sticks to proof this. Check the attachment.
Edit: Checksum Fixed!
Thanks!Quote:
Originally Posted by Giana
I think I'll try that...
Look my post #19, the mushkin dump in the link is a "pink" version (see the *.html report, it's 256MB stick).Quote:
Originally Posted by Ratax
Address 05 in the hex map defines the number of Dimm Banks, set "01" for 256MB stick and "02" for 512MB stick.
You need to fix the checksum, after editing the sdp file.Quote:
Originally Posted by Giana
^^ For what? Have done this for my Infineon 6-A Sticks without Checksumfix too. Works fine. Hm maybe Everest will not show SPD Infos without Checksumfix?
hmmm I have a pair of BH-5 that can't seem to be reprogrammed. They work fine if a little slow and can be accessed via Thaiphoon and apparently written to but when you reboot they just have their original SPD information on them. Anyone any ideas?
Everest will not show the mudule with the bad checksum and some others.Quote:
Originally Posted by Giana
For fixing the checksum:
after the hex "editing" load the sdp file edited with Thaiphoon Burner, go to: EEPROM => fix checksum or (ctrl+F) and save the spd file .
^Sure ;) Know this Feature, but i dindt know why i should use it. But thx will Update the Attachment.
Either you didn't follow the steps correctly as described in the first post, or it has write protection and the software doesn't detect that. Hardware write protect can be disabled by unsoldering pin7 of the SPD chip (WP) from the PCB and connecting it to GND.Quote:
Originally Posted by Johnny Bravo
I used dump for G.Skill F1-3200DSU2-1GBLE (TCCD), memory runs OK again,
but cpu-z detect me speed timings:
200Mhz 8-4-4-2.5
and
277 11-6-6-3
but memory are certificated 277 7-3-3-2.5.
Where is problem? Wrong dump?
THe HW write protect isn't on but I suspect the SPD may be at fault. RAM was touch and go in duel-channel now it has black SPD syndrome :( I fear the SPD itself it a little faulty and the PCB too, Vcc line works intermittently, perhaps it's ben flexed in its lifetime and broken internal traces.Quote:
Originally Posted by Micutzu
Replace the SPD.... only way if the original spd is write protected.
Waus-mod, the write protection is activated externally of the SPD chip, trough pin 7 (WP). If pin 7 is grounded, WP is off, if pin 7 is connected to VDD then WP is on and the SPD cannot be rewritten.
How have you determined that WP is off ? I'd suggest inserting the module in the slot, and with the system powered off measure the resistance between pin 7 of the SPD chip and GND; if it's 0 ohms or close to it, WP is off, otherwise it's on and you can't rewrite the SPD unless you do what i've described in the previous post.Quote:
Originally Posted by Johnny Bravo
Just read through this thread and just wanted to double check before trying this. I have a stick of Redline that has issues booting, seems like cold boot but happens all the time. When I can occasionally get the stick to boot it works fine and has 0 errors. Does this sound like symptoms of SPD being screwed up? If so can someone explain why it will boot some of the time still? Thx.
Quote:
Originally Posted by Krimi 2000
It's the same thing with the OCZ PC3200 Gold that i've described on a previous page; the manufacturer puts looser timings in the SPD to ensure compatibility and safe booting on any system. All the SPD's i've posted are correct and double-checked, it's safe to use them.
Holy damm , i had 2X512 ocz rev3 winbond bh5 sticks that does 225-230 2-2-2-5 2.8~2.9vdimm unburned and the one after one day dead [thousand errors even at defaults ,,the max vdimm that i have used 4 this stick was 2.9~3vdiim] .
i sent it back 4 rma ... :(
I think it was fixable :(
Awesome thread by the waY @ Bravo Waus-mod
Ok learned that also :P So when SPD is WP, you have to solder a ground to pin7?Quote:
Originally Posted by Micutzu
Is there somebody, who has dump for corsair TwinX2048-3500LLPRO?
Thanks.
yeah WP is off, turns out it was supply line was at fault, have repaired it and now runs SuperPi 32M @ 260MHz 2-2-2-4. :) Still the programming seems intermittant, when a full rewrite takes place, timing data is passed over but lower section of hex is lost (manufacturer module details etc) strange indeed. How do you detect a software WP btw?
EDIT - inc pic of fixed SPD and marked on the read point for WP for reference for other people
http://img400.imageshack.us/img400/4...drepair2sm.jpg
I don't think there is such thing as a software write potection for the SPD. I don't know what may cause that problem on your system (incomplete reprogramming), maybe the mobo is at fault. What mobo are you using ? Can you try another one ?
When the SPD is write protected you have to unsolder pin 7 of the chip from the PCB and connect it to GND (black wire of the PSU, one of the Vss pins of the DIMM, anything that is GND basically).Quote:
Originally Posted by Waus-mod
<center><font size="5"><font color="red"><b>Warning!</b></font></font><br />
Please read the latest part in the startpost, as someone also told me the same thing i allready thought about it. S7e9h3n said i had to post this as it is very dangerous. So please keep this im mind... and not to blame others when having "really" dead ram!
Fair eough Waus-mod tho I didn't realsie the controller was also at risk ! I'm pretty happy with my mem now anyway so I thik I'll stop pushing my luck :)
Micutzu it's a P4GD1, I have a few other boards lying around but to be honest I'm happy it's back to normal so I think I'll leave it where it is for the time being :D
Here's a dump from "Crucial Ballistix pc3200" 512 mb.
Yay first post here :D
heres mine dump for anyone who might need it.
Micron Chips it is though , wonder if i could upload any dump from gskill ZX or balistx...
http://img356.imageshack.us/my.php?image=back3bg.jpg
I've modded my dump from bh-6 relabeled kingston kvr333 with the same settings of the mushkin special.. I see the same, stick won't really run higher than 177mhz 2.2.2.5.1t... But wait, the stick does run 263mhz 2.2.2.5.2t
I'll update with v-data relabeled utt sticks dump.
that's very interesting as i have the same issue with my UTT BH-5's from Twinmos. before i matched the SPD's i couldn't even get them to run without errors together at low speeds and 2T. i can get 245-250mhz 2-2-2-5 @3.2v's 2T though.
Source?Quote:
Originally Posted by audiojunk66
According to Alonso (a TwinMOS tech) BH-UTT is the exact same chip as original BH-die (175nm).
MorueM and omga14,
If command rate 2T helps your clocks there is only one part to blame: the memory controller.
Command rate is actually not a memory timing. It affects only the memory controller.
I finally got my 2x512 ballistix pc3200 to boot in my sisters comp, it didn't work on my own P4P800SE. thx to Waus and ofcourse the creator(s) of taiphoon i have my ballistix back and saved from rma :D.
Well, my 512mb corsair 3502v1.1 does run 263mhz 2.2.2.5.1t, and my 2x512mb v-data relabeled utt runs dual channel 245mhz 2.2.2.5.1t..Quote:
Originally Posted by largon
But when the 512mb bh-6 is there, then whoops, needs 2t to go past 175mhz..
So my mem.controller is defective? It's my winnie running it, I could try my venice too, but I doubt it'd change something. Anything more enlighting? I'm ready to try things..
MorueM,
Since you can run 1T with other dimms there must be something really wrong with the underperforming dimm. Command rate is a mem ctrl timing, thus results can not vary that much considering your Corsair stick has identical (but higher rated) chips.
Does your "defective" stick run DDR400 at any timings?
The fact that this has saved at least 1 person's RAM is enough to praise Waus, let alone the many many people that now have working kick arse modules again!!
- OCZ PC4000 Gold Edition VX (OCZ500512ELGEVX)
i'd like to see MorueM try the other core to see what the end result is. i won't have my other cpu back from RMA for a while and that one is a Clawhammer so i don't think things will get better for me than the current E6 core i have running.Quote:
Originally Posted by largon
Ouaou I was looking for a magic program like that when I had the Asus A8V mobo with an A64 3500+, the rams simply didn't run over 200 mhz propably because of the DDR333 SPD.
Here's my spd dump file for Kingston Valueram PC2700(DDR333) 256MB BH-6.
:toast:
I found it here on Xtreme but i think it was wrong too after i look a bit further.Quote:
Originally Posted by largon
But it's strange that the new BH-5 won't run very well on a Asus P4C800(-E) and a Dothan if the chips are the same:mad:
anyone got the dump for Buffalo PC3700 (old bh5) 512mb sticks
There you go, the 256MB file modded to 512MB.
I lose geil ultra X (tccd) 1 stick 512m ... only me with tccd dead ?
no Vmods ... just restart como and no boot :eek:
Well yoto,
Follow the Tutorial and it works again :D
I'll try ;)Quote:
Originally Posted by Waus-mod
Waus-mod, I have a problem :Quote:
Originally Posted by Waus-mod
http://img79.imageshack.us/img79/6259/thaip0ls.jpg
why there are greyed options and there is no "Read device" like in the tutorial ? :)
Maybe the chipset is not supported, what mobo are you using ?
HydroX:
What motherboard/chipset?
This is true, I tested that program on nForce 410/Geforce6100 and it didn't work at all no matter what modules. On KT266 (the best so far :D) or i915 no problems.Quote:
Originally Posted by Micutzu
nah, I'm using DFI LP UT NF3 250gb, and they said at their website, this program support NF2/NF3/NF4 chipset. :)
makes me feel very bad, because atm I have one stick of my teamxtreem dead :(
Well test it on a other pc.. :D
wow im pumped.
going to try this out on my dead 256 mushkin LvII 3200 stick... that was killed by an ocz booster though so odds are it really is dead. On the other hand it dies at 3.2v, i always felt like i got some bad luck maybe the spd just went bad when i was loading cpu-z.
Tried on a dead BH-6 (SPD) I have.........I'm convinced that SPD chip IS deffinatelly dead now....:D
Flashed 4 x Kingston Value Rams 256MB, into Corsair ......Starting by SPD = Cas 2-2-2-6.......:D :toast:
Please be carefull hipro.. and to take a look into the startpost (latest part) As it its very important to read it.
I flashed my Corsair BH6 2x512 to Mushkin BH-6 but they didn't perform any better so i flashed them back.Quote:
Originally Posted by hipro5
Memtest gives no errors at 233Mhz 2-2-2-5 (3,3V)with all runs for 3 houres but in XP they only will do 200Mhz 2-3-2(2,85V) 2-2-2 gives a error with SuperPi:mad: this is with a Asus P4C800-E and Intel M740.
dear friend, my crucial ballistix(micron 5B-D) not dead but if I run superpi32M @200(SPD 200 2-3-2-8) it failed.
I tested with memtest can pass until HTT260, can anyone tell me why/ what is the problem and how to fix it(if can), in this thread I can't find the dumb file for my crucial BL6464Z402 (512MB), anyone have it ?
thanks
Ok guys, i managed to resurrect my dead khx512 bh5 stick. It booted in other pc i tried and though windows wouldn`t recognize it, typhoon could see it and rewrite, it turned out that the checksum was corrupted.
Although it works now, the motherboard of the pc (i865 made by intel) i was using to rewrite, says that the SPD information is inconclusive and refuses to boot at higher speed than 266 (on northwood 533fsb).
In everest it can be seen that the SPD of the module is found only for 400mhz (2-2-2-6) and no other speeds. Can someone confirm this for 512 kingston bh5 sticks? What speeds do you see? I don`t have the other stick with me right now unfortunately
I will try it in the evening in my own motherboard.
What speed is the stick rated at (PC3000, PC3200, PC3500) ?
KHX3200k2/1g
So it`s PC3200. Also a friend confirmed, there is only one spd mode for these.
Yes, KHX3200 BH-5 has only one rating, DDR400 2-2-2-6. Here's the SPD you need for your 512MB stick, try to overwrite once again using this dump.
Already done, thx. I will post back when @ home.
So if my system doesn't run with the dead stick in, and I can't do hot swap, and I haven't any sdp programmer... This means i can't do anything more, doesn't it?Quote:
Originally Posted by Victorshen
Is everything ok here with my TwinMOS 512mb old BH-5 309WE
It give me sudden bluescreen etc.
What BH-5 dump is suitable for this stick:confused:
http://koti.mbnet.fi/dani69/Muut/Tha...roken_BH-5.gif
..and here is unhurt 512mn BH5Quote:
Originally Posted by Dani
http://koti.mbnet.fi/dani69/Muut/Tha...broken_BH5.gif
What BH-5 dump is suitable for this stick:slapass: :slapass:
I see you can write, so the logical assumption would be that you can read as well. :rolleyes:Quote:
Originally Posted by Dani
Why don't you do it then? There's a link to the right dump file on page number one.
Here is the link:
http://xtremesystems.org/forums/atta...5&d=1136726926
:D
Dani, take a dump from youre working stick.. and load it it the "damaged" spd. :)
Waus-Mod, why didn't you add my Twinmos Speed Premium PC3200 512mb UTT BH-5 dump? do you recommend using the "old BH-5" dumps for all the Twinmos BH-5's?
No as the warning says :) its better to load the "original" dump is the right sticks!
You Are A Legend :clap: :clap: just fixed my dead stick of ram.Quote:
Originally Posted by Waus-mod
I have 3 sticks of corsair XMS3500 BH-5, two with a hologram (one of which was dead) and a non hologram one
the non hologram has different spd in cpu-Z strange....
Anyway thank again your a legend :toast: i now have 3 sticks to find the best two from :)
Edit i also have two sticks of ballistix that dont seem to run right since i used them in the dothan rig, i am going to try this on them too
Just like to mention that I just fixed my dead BH-6 with a hot swap. It wouldn't boot in either of my rigs and I'm kinda in the middle of nowhere. I tried with the tape and that didn't work, so I waited till the screen came on and jammed him in.Quote:
Originally Posted by Victorshen
Not very clever I know but it did work. :woot:
@ Stigggeh and snatchmonkey... great guys :D love it
Does someone have dump for this stick.
Corsair tccd.
CMX512-3200C2 XMS3202v4.2
XMS3200 512mb 400mhz CL2
hmm, looks like the VX that died in my ultra-d is back again. thx guys :up:Quote:
Originally Posted by T_M
np khan :D just give them the old love again ;)
Excellent find:clap:. If anyone needs Twinmos SP 3500 512 MB 1A4T new BH-5 dump, here it is. :toast:
gonna try this on mine. they're only PC3200's though so i know i'm taking a chance. if things don't show an improvement i'll go back to the original SPD dumps for them. gonna try the old BH-5 dump for the TMSP's to see what happens there. if they go kaput then i'll have a reason to get new ram:D
What happens if i dump my kreton BH-5 (6) into my Twinmos CH stick ?
They dont want to run 2-2-2-x togheter =(
*Update* i was bored.
Updated the Twinmos CH stick with Kreton SPD.
It booted just fine =)
On to testing..
I do see myself bying LOTS of unbootable sticks in the future...
Another one down......My BEST 256MB BH-6.....:(
Hipro :D follow the tut m8 ;) they will come back tust me !
No go.....I HAVE to replace the SPD chip and reflash it again as I did to my other one.......:(Quote:
Originally Posted by Waus-mod
Really strange there hipro succes with replacing!... pm me for something special ;)
Hello guys, someone have something for this model of OCZ VX ?
- OCZ PC4000 Dual Channel Gold Edition VX
OCZ5001024DCGEVX-K
- OCZ PC4000 Enhached Latency Dual Channel Gold EditionVX
OCZ5001024ELDCGEVX-K
thank you !!!:)
signed
me too....:toast:Quote:
Originally Posted by giorgioprimo
Quote:
Originally Posted by Langley
who are you?:p:
ciao Langley !!:rotf:
Anyone have the dump file for GEIL ONE ES and S version?
Tx!!!....:D
I never used it and it has just told me trial is expired... why?
I can't use it...