Quote:
Originally Posted by bachus_anonym
thanks ;)
but I think it link to the wrong screenie, it shows 250, not 266 ;) :p:
Quote:
Originally Posted by bachus_anonym
thanks ;)
but I think it link to the wrong screenie, it shows 250, not 266 ;) :p:
This is OCZ VX3200 at 270x10, 2-2-2-6 @ 3.5 VDIMM. Completed SuperPI 32M at default VLDT and VCHIP! I picked up this 2x512 from Newegg for around $161 I believe. The sticks seem a tad slower than my XMS3500 at 267x10 though.
Board: DFI-Ultra-D
BIOS: 510-2
DIMM slots: #1/#3 orange
CPU: 3700+ San Diego
This is OCZ VX4000 at 261x11, but needs only 3.3 VDIMM. Doesn't go much higher. I have run the sticks at 260 @ 3.2 VDIMM, Memtest clean and 3D stable, but did not try a 32M run there.
abit an8 sli
mushkin pc 3500(heatspreaders intact)(bh-5)
3.5vddr 1.75 vtt
3500 clawhammer
http://members.cox.net/italygirl25/3500@268mhz.bmp
DFI LanParty SLI-D
3.4v DIMM
http://members.chello.pl/xt/BH6.JPG
FX-55
Ultra-D
2x512MB Corsair 3200C2 v1.1 BH-6
http://img.photobucket.com/albums/v6...89/270mhz2.jpg
I have BH-6....Vdimm is 3,7 without any cooling:D
http://img204.echo.cx/img204/2234/1525432m2ti.jpg
EDIT: I have read first post and i have changed this screenshot....now its 32M :)
All valid screnies have been added!
@kostek13
First of all, you have not provided any info as to what mobo and RAM are you using... Second, raise your screen resolution so you can fit 2 instances of CPU-Z (CPU and Memory tabs)...
Best I can get out of this 3200 Gold BH, 262Mhz 3.6v. Using 0704-2(Bigtoe mod).
http://members.shaw.ca/Eldonko/262-1.JPG
This is on the 7 series BIOS. I switched to the 310P after and could do it with 3.3v. (see new 270mhz below)
http://img.photobucket.com/albums/v475/musk/SP32M.png
Also just got 270mhz stable. 3.6vdimm
http://img.photobucket.com/albums/v475/musk/32M270.jpg
275.4mhz 3.6V
2x256MB BH-6 Infineon&Twinmos
http://img316.imageshack.us/img316/469/2754mhz9ia.jpg
DFI NF4 Ultra-D
Venice 3000+
:)
OCZ 3200VX, 3.55V
dfi nf3 ultra-d, 602 bios
3700+ san diego
http://www.shrani.si/pics/32m51370_resized.jpg
TMSP PC3500 BH-UTT coupled with 3000+ Venice and DFI Ultra-D.
No real burn-in yet, this is 252MHz at 3.4v.
Good work broQuote:
Originally Posted by szukalski
With a bit of burnin and some timing tweaks 260 should be possible... get into it! hehe
4x512 Twinmos SP BH-UTT 2-2-2-5-7-12-2T 245mhz@3.4v
DFI NF4 Ultra-D 0623-2
I´m happy to see this thread as a sticky, it deserves it.
Thanks for the work bachus_anonym!
I second that. The Winbond and TCCD NF3/NF4 threads have been great resources for my learning curve.Quote:
Originally Posted by KoNiaK
Big ups to Bachus! :toast:
2*256 ADATA BH5 313we 2/2/2/5/7/12/2/2/12 at 3.8v at the moment
DFI NF4 ultra D (bios 310p)
Venice 3000+
http://www.membres.lycos.fr/boblemag...uperpi32mo.JPG
4*256 ADATA BH5 313we soon test (giga k8n sli / Epox 9npa+ / DFI nf4 Ultra / venice 3000/ sd 3700+)
After a while, thread has been updated :) Thank guys :thumbsup:
I stuck this thread, together with TCCD one and Enjoy's list of 2x1GB OCs. I hope you will guys enjoy them :)
Here's some OCZ VX at 3.4v
http://suckasd.com/computer/fx57/utt32mpi.jpg
Thanks bachus :)Quote:
Originally Posted by bachus_anonym
3000+ 0517 VENICE
GSkill 1GBGH
DFI Ultra-D
My Super pi 32m
DDR540 2 2-2-5 3.5V
http://img385.imageshack.us/img385/3883/54032m1bw.jpg
Test rig:
AMD 3200+ Venice 0517 (very poor @ O/C)
2x512MB G.Skill GH
DFI SLI-DR
262 MHz, 2-2-2-5, 1T @ 3.5V (3.6V for stable Memtest86)
>>>Screen<<<
Result for entry :D
BIOS 623-2 / Yellow
331x9 : DDR540
http://img238.imageshack.us/img238/1...i32m1rf.th.jpg
Others for Interest
270x9 : DDR540
http://img238.imageshack.us/img238/3...i32m6pp.th.jpg
375x8 : DDR545
http://img238.imageshack.us/img238/4...pi329yh.th.jpg
CPUz Validation
** michael, my little suggestion:
you should check the multi. You know what I am saying.;)
4x512mb..
http://205.209.142.180/onepagebook/2...illgh2g32m.jpg
************************************************** *******
2x512mb; 32m passed , currently hold the 6th place
http://www.ocxtreme.org/onepagebook/...w/pi32mrec.jpg
Updated!
@Kevin
Always a pleasure to see 3rd fastest Spi32M on AMD ever!!!
@all
Those marked in white represent some of the FASTEST SPi32M calculations ever performed on AMD systems...
Here a old one.
Gskills GH 1GB, also memtest86++ stable.
http://xtremesystems.org/forums/atta...id=36073&stc=1
2 x 512MB Mushkin PC3500 Lvl 2 fully tweaked - 3,54V. Sry no shot for voltages, u just must believe me. ;)
http://img232.imageshack.us/img232/9374/32m24min4lb.jpg
Quote:
Originally Posted by boblemagnifique
MAJ
2*256 ADATA BH5 313we 2/2/2/5/7/13/2/2/12 at 4v
DFI NF4 ultra D (bios 309 or 702-2)
Venice 3000+
http://www.membres.lycos.fr/boblemag...5/278.1mhz.jpg
4*256 Adata BH5 (0313we) -> 3.6v :)
http://www.membres.lycos.fr/boblemag...270.2mhz2t.jpg
Here's a diced 32M for you. 2x512 redlines 2,2,2,5 Only problem is I didn't load the memory screen hope it still counts. Not sure if I will do any more dice runs till I get a 57. ;)
http://img295.imageshack.us/img295/7525/32mmod7bw.jpg
Here is Kingston hyperX KHX3000 2x256 on NF4. Soon I might give them even more volts and run again. They are 3d benchable at 270 3.6V.
:toast:
http://img212.imageshack.us/img212/4...265sp321ld.jpg
Bettered my previous run.
2x512 @ 260mhz @ 3.5v on Venice 3200+, DFI_NF4_1.00_BH&CH_030705 bios.
Omg. 2T!! What a n00b!!Quote:
Originally Posted by szukalski
Please disregard that previous post, I was testing 4 sticks just before that run and forgot to change back to 1T.
I will be back with the real deal though..
Redline XP4000.
http://img257.imageshack.us/img257/1...mresize5nc.jpg
http://members.lycos.co.uk/chaosik/m...e-265-3.5v.png
Redline HP3200 2-3-2 by default .. i managed to reach 265 with 2-2-2-5 ;]
i think that i can squeeze 2 or 3 mhz more ;] but i didn't had enough time to test it. 270 was unstable even @3.6v
i think its quite nice for ~140$ ..
Mushkin PC3500 Level 2's
http://img196.imageshack.us/img196/2...9x1332m4bc.jpg
Just a standard overclock result here. Gskill 1GB-GH
http://www.computer-tuning.nl/benchmarks/ghresult.JPG
GravediggA - 333x9=3003MHz DDR546 @ 5-2-2-2.0-1T - DFI Ultra-D (NF4 Ultra) - A64 Venice - Mushkin LvL II PC3500 :toast:
http://img372.imageshack.us/img372/5...hzkopie6kw.jpg
2x512MB Kingstone HyperX PC3200 (old BH-5)
Btw .. i don understand, why you dont write a voltage to each results.
http://dym.haluze.com/Images/Tests/memtest@270MHz.jpg
http://dym.haluze.com/Images/Tests/mem270mhz_SP32MB.jpg
Test Rig
- AMD Athlon64 San Diego 3700+
- G.Skill GH
- OCZ Powerstream 520
Never really had a chance to run 32mb SPI, and finally here it is. :)
Validation link
http://valid.x86-secret.com/show_oc?id=38651
http://myhome.hanafos.com/~onechu/ra...h_spi32mbb.jpg
http://www.xs4all.nl/~famchow/Memory...MHz_SPI32M.JPG
DFI nF4 SLI-D bios 623-3. Must flash -1 for little better performance. :)
A little more on the mem but at 11 multi instead of 10.
http://img.photobucket.com/albums/v6...2M271small.jpg
2xOCZ VX 3200
2xKingston Hyperx PC3000
http://img259.imageshack.us/img259/4...moonman1yw.jpg
Kingston 2*256MB KHX3200 277MHz@3.5v on DFI NF4 and Venice 3000+ DPMW:
http://xtremesystems.org/forums/atta...id=37253&stc=1
*** Updated ***
Waiting for more :) Thanks guys! :toast:
Hello Bachus,
Think you made some typos while updating the thread. :D
Some of the people's, including mine are updated as 2T instead of 1T.
Would be nice if you can check them out. :)
Regards,
formyfaith
Thanks for noticing that, formyfaith :)
It's now fixed! :toast:
DFI NF4 Ultra-D - Venice 3000+ - OCZ Value VX 2x 512MB
http://img.photobucket.com/albums/v4...king/pi32m.jpg
sorry if my screen looks messy
i've no idea how to show all the windows in my desktop :p:
2*512MB Twinmos Speed Premium PC3200 (UTT/CH-5 Week 03 Year 05) at 9x 262MHz@3.4v on DFI NF4 Ultra-D and Venice 3000+:
http://xtremesystems.org/forums/atta...id=37537&stc=1
my setting with 2x512 mushkin redline xp4000 3,5v bios 623-2 in DFI sli-d
http://img142.imageshack.us/img142/305/27032pi9sl.jpg
http://img142.imageshack.us/img142/2659/tweaker9mf.jpg http://img142.imageshack.us/img142/2083/prime2h6iv.jpg
the bests stable i can get until now :banana:
http://img142.imageshack.us/img142/4453/tudo2cp.jpg
all the memory setting in bios:
180
enable
1,5
02
00
02
07
16
02
02
02
02
2064
01 bus clock
enable
increase skew
0
level 5
level 2
07,0 nano segundos
fastest
05,0 nano segundos
256
disable
16x
07x
disable(4 bursts)
here is one interesting result...:)
dfi ultra-d, venice 3000+, 623-2 bios and...
1x512mb corsair pc3500c2 rev1.1 BH-5 + 1x512mb twinmos pc3200 1A4T BH-5...
<a href="http://imageshack.us"><img src="http://img288.imageshack.us/img288/6460/260httsuperpi32mbzutislotovi9l.jpg" border="0" width="1024" alt="Image Hosted by ImageShack.us" /></a>
can you guys tell me what settings effect super pi 32mb stability most...?? it seems i can't get my sp 32mb calculation finished past 260htt...maybe some other bios...??
4000 Redline & 0704-2BTA.
http://members.shaw.ca/zryan/270-2.JPG
Hello everyone. I tested my new bh5 OCZ EL DDR PC 3500 Platinum Limited Edition sticks and they managed to finish the test at 270 mhz at 3.5 volts Here are the results
Geil One BH-5, DFI NF4 Ultra-D@SLI-D, OCZ Powerstream 520W, SD 3700+
http://img377.imageshack.us/img377/4...m270mhz7fu.jpg
http://img377.imageshack.us/img377/2...tavitve2bv.jpg
http://img276.imageshack.us/img276/8...190024a2yi.jpg
:banana: :banana: :banana:
Minimum x9 multiplier required :(Quote:
Originally Posted by GUFY
Geil One BH-5, DFI NF4 Ultra-D@SLI-D, OCZ Powerstream 520W, SD 3700+
http://img228.imageshack.us/img228/6...erpi32m4si.jpg
Sory my mistake, but may ram can do even better :banana: :banana: :banana:
Bios is 623-2, tref 2592, Drive stength 7 and Data Drive stength 3.
I hope to rich 275 MHz with this ram. :)
*** Thread updated ***
Yay! 83 entries! Keep those results comming, guys! Thanks a lot :toast:
BTW, I cleaned up this thread a little...
Let's try to keep it straight up to the point - screenshots only, please :) Nice & Clean...
bachus_anonym: Thanks :)
Vdata UTT/BH-5 (Week 16 Year 05) 9*263Mhz@3.6v on DFI NF4 Ultra-D/Venice 3000+ DPMW:
http://xtremesystems.org/forums/atta...chmentid=38698
Corsair LLPT 3200 BH5 @265fsb
Trying for 270 now.
http://www.xtremesystems.org/forums/...id=38819&stc=1
A64 3500+ Winchester
DFI NF4 Ultra-D
2x256MB Kingston HyperX PC3500 BH-5
1.5-2-2-0 1T @ 271MHz
3.65V (extra voltage does very little to help)
Memtest stable for many hours
Note: CPU not totally stable at 2.71GHz, so 10x multi cant be used for 32m.. I can 3dmark fine with 2.7, so these screenies were done with 9x multi.
http://www.xtremesystems.org/forums/...chmentid=38968
OCZ VX3200, it does max 254 mhz. 32m time was 24m 43.109sec.
http://i20.photobucket.com/albums/b2.../32m_3g_vx.jpg
for now add me these freq :D
i can do better tho' :banana:
http://img450.imageshack.us/img450/6584/25018qk.jpg
http://img431.imageshack.us/img431/3130/25026ut.jpg
4x512 GSkill GBGH :woot: mobo sli-dr
here's another update from here :toast:
http://img260.imageshack.us/img260/1955/26126xi.jpg
:woot:
Corsair XMS PC3200LL REV.1.1 256mb x2
274.5 (DDR 548) Vdimm 3.6V
Venice 3200+ @ 305x9 = 2745Mhz
DFI NF4 Ultra-D (Bios 623-3)
Posted this at OCForums, hope the duplication won't hurt :)
New settings with 512 x 2 Muskin Lvl II blk PC3500-BH5
-----------------------------------------------------------------------
I'm using the 6/23-3 (still TCCD specific, but hey I'm getting good results!)
Last Updated:Oct 23, 2005
Motherboard: Lanparty Ultra-D
Bios: 6/23-3
CPU: 3200+ Venice (Rev E3)
VC: BFG 6800GT 81.85
OS: Windows XP Pro w/SP2
Ram: Mushkin lvl 2 Black PC3500 (Original BH-5) In the Yellow DIMM slots
Chipset Drivers: Revision 6.66 (w/out IDE)
DRAM Timings:
- Ram Multi 200 1:1
CPC ENABLED
Tcl 2
Trcd 02
Tras 02
Trp 02
Trc 07
Trfc 12
Trrd 02
Twr 02
Twtr 01
Trwt 02
Tref 3072
Twcl 01
Bank Inter EN
Dynamic Skew Control Increase
Skew Value 255
DRAM Drive Strength 06
DRAM Data Drive Strength 01
DRAM Response time: Fastest
Max Async 9ns
Read Preamble 5ns
Idle Cycle 128
Dynamic Counter EN
R/W Que Bypass 16X
Bypass MAx 7X
32 Bit Gran DIS
Voltages etc:
- HTT 270
LDT X2.5
Cpu Multi X10
PCE-I 100
Vcore Startup 1.525
Vcore 1.450
Vcore Special 113%
LDT V 1.4
Chipset V 1.7
Vdimm 3.6 + DRAM .03 Enabled
Extra Notes and observations:
- - If TWCL was set to 02 instead of 01, I had to reset the CMOS. TWCL always at 01
- Data Drive strength can be set to level 8, but I'd have to loosen a few timings. I can choose between 6 and 8. 6 seems t0o get me more BW.
-If Twtr was set to 01/03 instead of 02, there was no BOOT.
- I tried tREF to AUTO and then picked off 3072 from a64 tewaker.
Proof of stability and other links:-
http://valid.x86-secret.com/show_oc?id=45474
http://img360.imageshack.us/img360/8388/bh5new1zh.jpg
*** Thread updated ***
Thanks a lot for great results and participation in this little fun we have here :toast:
Here's mine.
A64 3200+ Venice, DFI NF4 SLI-DR (BIOS 623-2), 2x512 OCZ Gold VX PC3200, OCZ Powerstream 520w.
Trying to see if I can squeeze more without increasing the DRAM voltage...
http://www.xtremesystems.org/forums/...chmentid=39770
EDIT: How dumb of me. I blocked out the bit of SuperPi that shows that I ran the 32m test. I'll re do it if it's required. :)
bachus_anonym
Thanks for updated :toast:
Also,here's a new record of mine, 279mhz on the bios 623-2 . :D
Next steps will try to removed the stock heatspreader,to see if it can break the barrier of 280 mhz .
OK, had to delete my first post, but after an evening of fiddling I am at SuperPi 32 M and x9 multiplier.
This is my Opteron 146 CABYE 0540 FPAW at 1.65 Volts and 4x 512 MB Geil One BH at 3.6 Volts.
Big Typhoon and 80mm fan directly only the 4 RAM modules.
http://www.cons.org/cracauer/oc-scre..._4sticks_5.png
http://www.cons.org/cracauer/oc-scre...4sticks_5b.png
I am working on doing the same thing with a x10 multiplier as we speak. [done, this is the x10 shot]
*** Thread updated ***
It looks like the pace is a little slower this time around :D Come on guys, keep me busy here :)
Thanks a lot for sharing some nice results :up:
My Config.
A64 3000+ Venice step E6
DFI NF4-D
2x512 mb GEIL ONE W
ZALMAN CNPS 9500
Thanks to All my Friends ;)
This is for you
The Return of BH IC
http://img195.imageshack.us/img195/6...lonewok1kg.png
Here is the best I can do for now - 271 MHz @ 2-2-2-5
Geil One BH 2x 512 MB @ 3.6 V. CABYE 0540 FPAMW @ 1.6 V, DFI SLI-DR, OCZ 520 W.
http://www.cons.org/cracauer/oc-scre...perpi32m_6.png
Does prime95 at 268 MHz same settings.
EDIT: Win2k; LargeSystemCache=0 :(
See signature for details. This is not the highest I can take the memory at 2-2-2-x. Ive been able to hit 267FSB but since my CPU maxes out at around 2770 with 1.65v, my best choice is to run around FSB252x11.
http://i15.photobucket.com/albums/a3...Pi32mbEVER.png
At least with my score there will now be 3 posts for the 754 division :D
OCZ VX PC4000 2x512mb @ 265 2-2-2-5 3.5v :toast: Everything else set to auto in the BIOS. I'm sure these sticks are much capable of more, but I don't have the results ATM ;)
http://img235.imageshack.us/img235/1...535v32m7jd.jpg
EDIT: 27minutes i believe. with the CPU at 3ghz and RAM 250 2-2-2-5, i get 25.5 minutes.
i'm using the NF4X Infinity so i don't have the choice to use a 183 divider and my max v is 3.2v's. so here's my max 32M with BH-5(forgot to change tras).
http://img42.imageshack.us/img42/580...copy7mn.th.jpg
281 Mhz with a multiplier X10 ,Vdimm 3.7V
SPi 32M calculation time = 25m25.250s :woot:
and here's the ss
http://img526.imageshack.us/img526/8...z32m8zx.th.jpg
Hi
that's the Score from my sticks.
Opteron146 @ 2900Mhz Multi *10 , Twinmos pc3200 AA4T 2.2.2.5 264Mhz 3.6vD
http://img457.imageshack.us/img457/4677/26432pi4tv.jpg
PEaCE
Done ! Needed a RDX200 :)Quote:
Originally Posted by KenLau
Cpu-Z validation : http://valid.x86-secret.com/show_oc?id=57935
http://www.klokking.com/bilder/32_282.JPG
TeamGroup Xtreem BH-5
277x12, 2-2-2-5, DFI Ultra-D BIOS 703-2 Merlin Moded version
Info picture below:
http://www.ocxtreme.org/onepagebook/ddr550piset/32m.jpg
Here's some 4x512Mb action.
TMSP PC3500 BH-UTT @ 250MHz @ 2-2-2-5-7-12-2-2-1-2 @ 3.3v
The 148 won't accept lower preamble/async values running a divider at 300HTT unfortunately.
http://img478.imageshack.us/img478/8...22253pt3v2.jpg
*** Thread Updated ***
Congrats to Kevin (Onepagebook) for sweet new record of 277MHz @ 5-2-2-2.0-1T :clap:
Sorry for a bit of slack on an update :p It will happen again :lol: But don't stop submitting new entries! Thanks a lot for participating, guys :up:
Upped the MHz in a search for a better daily setup, same deal with the preamble/async though :(Quote:
Originally Posted by szukalski
TMSP PC3500 BH-UTT @ 258.5MHz @ 2-2-2-5-7-12-2-2-1-2 @ 3.5v
http://img401.imageshack.us/img401/8...mhz22256ab.jpg
2.92 GHz @ 1.425V + 4.8%
Thermalright XP-90C with Panaflo 92mm M1A
SuperPI 32M stable... :hat1:
http://img399.imageshack.us/img399/8...eron1465bx.jpg
http://img399.imageshack.us/img399/7884/ocopty2fq.jpg
Finally broke the 2800MHZ barrier thanks to the winter and moving from Texas to Utah!
Got a new best score! I am keeping my 11 multi so my CPU is holding me back for higher FSB but I am of course trying to get the highest CPU first and highest FSB second. Here is my biggest achievement yet for the 754 NC 3400 on air.
http://i15.photobucket.com/albums/a3...i32MBa2806.png
My best time has been 29min 11segs when I shut down outpost and nod32.
Mushkin + Corsair Pc3500
A64 Winchester
http://ocing3.free.fr/FTP/overclocki...s000-n%b03.png
DFI nF4 SLI-D, Opt 146, AIR cooled CPU&MEM -1'C :cool:
CORSAIR CMX256A-3500 C2
XMS3502v1.1
024704
Stick1:
Winbond
2452D
W942508BH-5
and same stepping on other side
Stick2:
Winbond
2452D
W942508BH-5
and the other side
Winbond
2462D
W942508BH-5
http://koti.mbnet.fi/dani69/DFI%20nF..._1.64V_AIR.gif
http://koti.mbnet.fi/dani69/DFI%20nF...s_1.7V_AIR.gif
Opteron 148 @ 264x11 = 2904Mhz
2x512MB OCZ PC3500 Platinum Ltd. Edition BH-5 @ 264Mhz 3.31V
Rest of info in my sig.
These bad boys definitely have some more in them, but this is about the max of my CPU with 11 multi. I'll drop it down to 10 tomorrow and see if I can't set the record :D
2x256mb Corsair PC3200LL V1.1 (303we)
283mhz DDR566 6-2-2-2-1T vdimm 3.7V
DFI Lanparty NF4 Ultra-D (Bios 623-2)
23 loop
http://img218.imageshack.us/img218/3...op234uc.th.jpg http://img218.imageshack.us/img218/2378/2830zi.th.jpg http://img218.imageshack.us/img218/3...z32m5qd.th.jpg
nice KenLau :toast:
No i`m in 3. , have to do something about that ;)
Fosco , thanks !! :toast:Quote:
Originally Posted by Fosco
For the last mhz,it spent me a lot of times on it :slapass: ,I think I need a 600W psu or a 5V rail mod and see if any help with it. As I Know Norway is very cold now ,and hoping the Mr.cool will give you a help .:D Keep on pushing it,mate !!
Small update:Quote:
Originally Posted by HiJon89
Opteron 148 at 2.7Ghz (10x270)
2x512MB OCZ PC3500 Platinum Ltd. Edition BH-5 @ 270Mhz 3.4V
Rest of info in my sig.
EDIT: Forgot to mention, Bank Interleave still enabled.
http://img.photobucket.com/albums/v6...H-5/27032M.jpg
Small Test with new DFI nF4 Ultra-D: 260Mhz 1,5-2-2-0 (all Timings tweaked) @ 3,28VDimm :p: couple of hours Prime-Blend stable... BUFFALO Value with new BH5 - that's cheeeeeeap! :woot: Sticks runnin' passive, only PWM @ 80mm Fan. PSU is an AcBel 400W :cool:
http://img75.imageshack.us/img75/2093/260mhz7af.jpg
Timings:
http://img75.imageshack.us/img75/3513/tweaker6gc.jpg
:clap:
My results are to bad to show, I thought I would ask you guys with DFI Lanparty UT NF3 to help me a little bit (guys who dont have that mobo can help me if they can to :p: ) I have 2gb of BH5 , 4x512, 3xOldschool 1x Speed Premium, 2 of the oldschool are almost identical, ~3errors in test5 DDR500 3.18v (single channel) but if I try to run them in dual channel mode they wont even do 240 with 3.2-3.6v. The CPU is a SD 3700+ running at 273x11 (for now with a 166 divider) I know that both of them are good for at least 260+ so I think ive missed something, im curious about one setting in bios (but I dont know the name of it) the values are "not reduction" "15% reduction" "30% reduction" "50% reduction" or something like that, dont know wich one of them to use since I dont know what it means. running BIOS 711 btw.
here is mine :) 2x512MB Gskill GH UnTesTed BH5, doing 255 @ 2225 with divider at 3.68v.
http://img64.imageshack.us/img64/295...ght11gl.th.jpg
by the way, uOpt, although your ram speed & cpu speed is much higher than mine, but my result seem better than you. wonder why? :confused:
2X512 Corsair PC3200C2 Rev1.1 (BH-6) @ 3.72v
DFI SLI-DR Expert
http://img369.imageshack.us/img369/7...3x1232m3oy.jpg
http://valid.x86-secret.com/show_oc?id=66085
Got 272Mhz stable. Here's a shot of 1095 passes of Test #5 with 0 errors at 272Mhz 3.47V:
http://img.photobucket.com/albums/v6...272Memtest.jpg
and here's a 32M at 272Mhz 3.52V:
http://img.photobucket.com/albums/v6...H-5/27232M.jpg
Bank Interleave still enabled.
Wow how old are your dimms? Mine have 3 months (heh) and they need 3.5v to be stable at 250 2-2-2-5.