OPB's New BH-5 records(FSB) on DFI SLI-DR

Printable View

Show 100 post(s) from this thread on one page

02-07-2005, 02:24 PM
Onepagebook

Quote:

Originally Posted by HARDCORECLOCKER

:D THX OPB - You always suprise us again with something new - myself didn't know that....... :toast:

just wondering my bro,
you play those twtr and trtw setting see what happened? :D
try (twtr as 1, trtw as2 )compare with (twtr 2, trtw 3) ----> play with Sandra.;)
02-07-2005, 02:38 PM
HARDCORECLOCKER

Quote:

Originally Posted by Onepagebook

just wondering my bro,
you play those twtr and trtw setting see what happened? :D
try (twtr as 1, trtw as2 )compare with (twtr 2, trtw 3) ----> play with Sandra.;)

:D Yep - will try, not much experienced it because all my RAMs are single sided 256 MB.......... :toast:
02-07-2005, 04:04 PM
kryptobs2000

Quote:

Originally Posted by Onepagebook

If you have single side ram, go with odd numbers of level setting like 1,3,5,7
while you need to set it as even number like 2,4,6,8 if you have double side ram.:D

OPB

I got 2x512, so double sided, I always set my drive strength on my dfi 250gb to 1, so say I move it to 2, what would happen (I'm using my kv8 pro right now as my temp sensor on the dfi is crap so I can't test it). But would it allow me to clock higher or improve performance or what? Right now my max with 3.6v is 265mhz 99% stable, all timings as tight as normal tight timings go, 2-2-2-10-7-12...
02-07-2005, 07:05 PM
jll

Hi OPB, great score!!!! I'm impressed! :)

I have some doubts, nothing special.

I noticed that your Dram was 3.96v but the 3.3v line was just 3.39. When I raise my vdimm to about 3.5 I set my 3.3v line in the psu to 3.7, is this correct?

Now for example I have 3.5 on the psu and 3.3 on the ram, and the 4x256 modules dont even get warm (all Bh5)! :)

Best wishes

Jorge Lopes
02-07-2005, 07:50 PM
P_1

Quote:

Originally Posted by jll

Hi OPB, great score!!!! I'm impressed! :)

I have some doubts, nothing special.

I noticed that your Dram was 3.96v but the 3.3v line was just 3.39. When I raise my vdimm to about 3.5 I set my 3.3v line in the psu to 3.7, is this correct?

Now for example I have 3.5 on the psu and 3.3 on the ram, and the 4x256 modules dont even get warm (all Bh5)! :)

Best wishes

Jorge Lopes

err hes using the 5v jumper on the dfi board, so the power to his vdimm is comming from the 5v rail
02-07-2005, 11:30 PM
jll

ok thanks!

Didn't know that! :slobber: Always learning! :)

Bye
02-08-2005, 01:43 AM
QuadDamage

Quote:

Originally Posted by MrIcee

Quad my old friend:)

Great to see you ! And while reading this I'm glad someone remembered that run I made with OCZ PC3500 Platinum LE back in December '03. I was reluctant to toot my own horn here, but that accomplishment can be found here and here . Granted it was single channel.

Hats off to OPB for pulling this feat off in dual channel with BH-5 ! :up:

And those are right about the 1/2 multi deal, we did not know that issue at that time.

Just be careful with 4v to your memory controller, extended time spent there will have you posting to C1 on a debug card;)

Randi:D

Randi:D,

Long time no see indeed. I thought you were running at 4x multi actually. But let's not forget it was over a year ago and no one at that time could come even close to your sandra scores:) Those days i could only do 10x267 6:5 on Giga ES mobo and that was more than enough to get AMD back to the top of the ORB in '01 after like two or three years of Intel benching dominance. I was scared to think what you could've done with your OCZ ram, Shuttle mobo and a well cooled vid card....
02-08-2005, 05:40 AM
SAE

Great clocks, congrats.

I really wonder what mine can do... I will get to know when I get my FX-55 (delaysdelaysdelays... ) :D DFI 's on the way, x850xtpe as well ;)
02-08-2005, 06:00 AM
Dani

Quote:

Originally Posted by TEDY

dani you mean DFI NF3 not DFI NF2 ? :D

Nope, those mems do +270FSB with tights 1:1 on DFI nF2, DFI nF3 and hopeful on DFI nF4 too (shes coming tomorrow) :toast:
02-08-2005, 07:01 AM
amv1981

Quote:

Originally Posted by MrIcee

Just a friendly warning:) I too spent weeks at 3.8v and above, then one day you will not post, and the debug card will leave you at C1, "trying to detect memory". Believe me, I've been thru enough A64's in testing since their release to know, and the reason I discontinued buying OEM;)

Randi:D

so the Vdimm does effect the A64 chip?!!? Damn I did not now this I only thought it was hard on the actual mem only!!

What is considered safe V then for 24/7 use using air??

Currently I am running my BH-5@3.1

/A
02-08-2005, 07:10 AM
bias_hjorth

3.3v should keep you quite safe :)
02-08-2005, 07:13 AM
kryptobs2000

I run 3.5-3.6v 24/7 with a fan on the memory, but I can't testify whether it's safe, just that I do it anyways lol
02-08-2005, 07:23 AM
amv1981

Well I don't care bout the mem atm - I was just thinking about what mrIcee said about the mem controller on the actual cpu!

I know 3.1 won't hurt my mem - but what about my cpu??

cheers

/A
02-08-2005, 08:13 AM
Onepagebook

Quote:

Originally Posted by SAE

Great clocks, congrats.

I really wonder what mine can do... I will get to know when I get my FX-55 (delaysdelaysdelays... ) :D DFI 's on the way, x850xtpe as well ;)

haha I know your x850 xt pe is on the way though, I got one too.
hey, thanks to Saaya. :D :banana:
02-08-2005, 11:19 AM
killingspreez

i'd like to know, if 3,1 v would damage the cpu? i didn't notice anything till now :)

and btw! increasing the drive strength didn't change anything! i have the SAME sandra benches!

would should happen?

mfg
02-08-2005, 03:37 PM
SAE

Quote:

Originally Posted by Onepagebook

haha I know your x850 xt pe is on the way though, I got one too.
hey, thanks to Saaya. :D :banana:

On the way?! Nicccce! :D

I hope I get it soon, so I can at least weigh it in my hands dreamin' of what could be with an FX :lol:
02-08-2005, 03:38 PM
kryptobs2000

well if 3.6v dosn't hurt my memory controller, I doubt 3.1v is risking anything
02-08-2005, 04:58 PM
Onepagebook

Quote:

Originally Posted by SAE

On the way?! Nicccce! :D

I hope I get it soon, so I can at least weigh it in my hands dreamin' of what could be with an FX :lol:

same here, will have that tommorrow though,
I will try it on BH-5 as high as I can. :p:
02-08-2005, 05:17 PM
SAE

Quote:

Originally Posted by Onepagebook

same here, will have that tommorrow though,
I will try it on BH-5 as high as I can. :p:

Your 01 score will shine for sure!!! :thumbsup:
02-09-2005, 03:23 PM
Onepagebook

Quote:

Originally Posted by SAE

Your 01 score will shine for sure!!! :thumbsup:

Thanks Master:D

here is the first try with 286fsb(BH-5)x11, x850 xtpe all air-cooled with 3d2001;), how do you think? I really appreciate saaya told me that cheap x850xtpe..haha, and more importantly, it rocks.. :D
nothing tweak, it's on the win2k3
Here is the official score link:
http://service.futuremark.com/compare?2k1=8419743

http://img208.exs.cx/img208/2369/x850xtpe013rj.jpg
02-09-2005, 03:31 PM
JNav89GT

wow
02-09-2005, 03:36 PM
SAE

Great score for first run on air :thumbsup:

With a lil tweaking and higher card clocks (and higher Fx clocks under your cascade ;) ) you will definitely break 40k IMO. The hardware is able to do it as you are as well.

These fsb clocks on bh-5 make me even want my stuff more... :lol:
02-09-2005, 03:37 PM
bachus_anonym

Damn, OPB :slobber: :thumbsup:

Superb clocks there!

When you get a moment can you do me a huge favour and try to run SuperPi 16M unpatched on it, plizzzz ? I'm very curious if you can get it below 10m00s...

Thanx,

BTW, what voltage is that BH-5 at?
02-09-2005, 03:38 PM
saaya

Quote:

Originally Posted by Onepagebook

haha I know your x850 xt pe is on the way though, I got one too.
hey, thanks to Saaya. :D :banana:

yes, i helped sae to get an x850xtpe as well :D
your welcome! im glad it clock that nicely and you enjoy it!
have fun with it :) :toast:

btw SAE, i got a confirmation for the fx55 you wanted, next week ;) hit me up on msn :D

Quote:

Originally Posted by Onepagebook

I really appreciate saaya told me that cheap

your welcome :toast: get some nice numbers out of it! that memory should be able to do more, make sure you use a psu wire for it that is not plugged to any other devices to it gets a clean and interference free cable directly from the psu! maybe the card needs more fresh air? what air temp is it there? i have seen 6600gt cards with 1.6ns gddr3 from samsung that did 1340mhz totally stock with even no heatsink on the memory! :D

maybe the heatsink on this card actually makes the memory get even hotter? maybe the heat from the overclocked gpu is transfaired to the memeory by the heatsink? try to overclock the memory without overclocking the gpu and see if you can get a higher overclock! :)
02-09-2005, 03:39 PM
madgamer

Wow on that 3d mark 01 score. That and who needs your x-files ram when you have bh-5 that will do speeds like those in that shot above. 2-2-2-4 at that speed (and stable) is nuts.
02-09-2005, 03:46 PM
saaya

kevin, is 2-2-2-4 really faster than 2-2-2-5 or 10 or something else? or did you just use it because it looks good? :D
02-09-2005, 04:21 PM
Revv23

Quote:

Originally Posted by saaya

yes, i helped sae to get an x850xtpe as well :D
your welcome! im glad it clock that nicely and you enjoy it!
have fun with it :) :toast:

btw SAE, i got a confirmation for the fx55 you wanted, next week ;) hit me up on msn :D

your welcome :toast: get some nice numbers out of it! that memory should be able to do more, make sure you use a psu wire for it that is not plugged to any other devices to it gets a clean and interference free cable directly from the psu! maybe the card needs more fresh air? what air temp is it there? i have seen 6600gt cards with 1.6ns gddr3 from samsung that did 1340mhz totally stock with even no heatsink on the memory! :D

maybe the heatsink on this card actually makes the memory get even hotter? maybe the heat from the overclocked gpu is transfaired to the memeory by the heatsink? try to overclock the memory without overclocking the gpu and see if you can get a higher overclock! :)

perhaps the 6600 card has a higher stock voltage on memory?
02-09-2005, 05:04 PM
Onepagebook

Quote:

Originally Posted by bachus_anonym

Damn, OPB :slobber: :thumbsup:

Superb clocks there!

When you get a moment can you do me a huge favour and try to run SuperPi 16M unpatched on it, plizzzz ? I'm very curious if you can get it below 10m00s...

Thanx,

BTW, what voltage is that BH-5 at?

Hi dear Bachus..
If I am correct, it is 3.8v I think
I will find a time to run 16m no problem :)
02-10-2005, 07:20 AM
SAE

Quote:

Originally Posted by saaya

btw SAE, i got a confirmation for the fx55 you wanted, next week ;) hit me up on msn :D

Great! :D

I will see ya on MSN, you have not been online yet. :D (have to go to work this evening, coming back 10pm, mate).

Hmm, I am wondering about what you said about the 1.6ns mem... didn't nvidia gf5 and 6 cards always a load better on the memory than their ati opponents?

It may be a pcb layout problem. (BTW I think, he has not really started playing with it ;) )
02-10-2005, 07:28 AM
HARDCORECLOCKER

Quote:

Originally Posted by SAE

Great! :D

I will see ya on MSN, you have not been online yet. :D (have to go to work this evening, coming back 10pm, mate).

Hmm, I am wondering about what you said about the 1.6ns mem... didn't nvidia gf5 and 6 cards always a load better on the memory than their ati opponents?

It may be a pcb layout problem. (BTW I think, he has not really started playing with it ;) )

:D So at last You've been succesful with Your search - hope for a good clocker so.......... :toast:
02-10-2005, 07:29 AM
Gamer

hmm, thought you can do better than that OPB ?

http://service.futuremark.com/compare?2k1=8309330
all air too but tweaked :p
02-11-2005, 09:29 AM
saaya

Quote:

Originally Posted by Revv23

perhaps the 6600 card has a higher stock voltage on memory?

would be surprised to see... maybe its the memory controller... we all know that memory ocs different on nf2 nf3/4 and 865/875 or 915 chipsets... so maybe the memory scales higher on the 6600 memory controller...

and yeah, maybe its also a pcb thing, good idear! the 6600s only have a 128bit memory bus wich means the design is much simpler and thus probably allows the chips to clock higher, just like different pcb designs for memory sticks. since its only 128bit they had more pcb space for the traces and could isolte them better or make them shorter...

i guess its a mix of all of this :)

its really nice to see a mid end card outperforming a super ultra high end card . at least when it comes to the memory clocks :P heheheh

Quote:

Originally Posted by HARDCORECLOCKER

:D So at last You've been succesful with Your search - hope for a good clocker so.......... :toast:

in the end he decided to not cancekl the order he already made for an fx55 and wait until that shop gets fx55 chips... so we will have to wait some weeks until we see SAE pulling some insane numbers again :( :D

Quote:

Originally Posted by Gamer

hmm, thought you can do better than that OPB ?

http://service.futuremark.com/compare?2k1=8309330
all air too but tweaked :p

this was just his first test, he just checked how well the card clocked out of the box :P
02-11-2005, 10:56 PM
[G.N.U.]Fragman

anyone tried the OCZ pc4200EL (should be hynix chips) on the final DFI sli-D board?
02-12-2005, 04:25 PM
Melchior

very nice man!

i think because of you my overclock-madness will have a comeback ;)

just got to sell my 4gb of bh5 and buy some 256mb sticks and better stuff...

cya in hell :toast:
02-12-2005, 10:53 PM
linhvndiy

Hi! When you maxout your BH-5? Why dont you test with multi 11???Can not only 8k sisoft???
02-13-2005, 02:22 PM
jan

1 Attachment(s)

With this settings I booted into windows at 3.7 Volts.

I hope I can get some more mhz out of it with some more volts. :)
I am just waiting for the DFI-NF4 Ultra

http://www.xtremesystems.org/forums/...id=24575&stc=1
03-01-2005, 11:35 AM
Onepagebook

Quote:

Originally Posted by jan

With this settings I booted into windows at 3.7 Volts.

I hope I can get some more mhz out of it with some more volts. :)
I am just waiting for the DFI-NF4 Ultra

http://www.xtremesystems.org/forums/...id=24575&stc=1

Any resesult from DFI ultr-D?
03-13-2005, 03:53 PM
Ref

OPB, what's your max. screen ? And max. sandra bench ?
03-14-2005, 05:56 AM
boblemagnifique

:toast: DFI / BH5 :banana:

2*256 ADATA BH5 (0313we) 2/7/12/2/2/5/2/2/1/2 , 3.9v :)
DFI NF4 ULTRA D
3200+ CBBHD 0447 TPEW
Box AMD (tower outside)

http://www.membres.lycos.fr/boblemag...uperpi28s2.PNG
http://www.membres.lycos.fr/boblemag...we2/295mhz.PNG
http://www.membres.lycos.fr/boblemag...nf4/fsb504.png
http://www.membres.lycos.fr/boblemag...ie@3140mhz.PNG
03-14-2005, 06:02 AM
funkflix

Nice one! :toast:

Which bios do u use? U had any problems to get more then the 3,8V setting working on the DFI? I always get BSODs when i set it to 3,9V or above...
03-15-2005, 09:25 AM
boblemagnifique

Quote:

Originally Posted by GravediggA

Nice one! :toast:

Which bios do u use? U had any problems to get more then the 3,8V setting working on the DFI? I always get BSODs when i set it to 3,9V or above...

3.10 Modded -> FSB 504
2.18 -> for the remainder

my bh5 is stable 3.8/3.9v in bench but has 4v at home it is very unstable :rolleyes:
03-15-2005, 09:36 AM
HARDCORECLOCKER

Quote:

Originally Posted by boblemagnifique

3.10 Modded -> FSB 504
2.18 -> for the remainder

my bh5 is stable 3.8/3.9v in bench but has 4v at home it is very unstable :rolleyes:

:confused: Do You mean 3.10p ???

:toast:
03-15-2005, 09:46 AM
boblemagnifique

http://www.techpowerup.com/articles/other/114
03-15-2005, 10:49 AM
HARDCORECLOCKER

Quote:

Originally Posted by boblemagnifique

http://www.techpowerup.com/articles/other/114

:D THX, nice link - but again what do You mean with the mod version of 3.10, are You using the 3.10p (performance) ???

Or is it me, a little stupid....... :p:

:toast:
03-15-2005, 10:53 AM
Onepagebook

ya , I am also kinda lost, cuz what my post has 2 bios only, only 390-2 and 310-2.
03-15-2005, 07:41 PM
jinu117

Sigh... gave up trying to get to those... just got another pair of BH-5 512x2 and got it to 270 2-2-2-5 @ 3.8v... looking at how it curved, think max probably is around 275 4.0v... not going to risk it.... :P Time to work on divider and lower the volt... I am impressed at how this DFI is taking BH-5 into new startosphere. (all other settings on memory were stock other than 2225 part... I don't pretend to know all these memory settings... :P)
03-15-2005, 08:13 PM
EMC2

Hands OPB vision clarifiers

Quote:

Originally Posted by Onepagebook

ya , I am also kinda lost, cuz what my post has 2 bios only, only 390-2 and 310-2.

The 310p is on DFI's beta BIOS site ;)

Show 100 post(s) from this thread on one page

All times are GMT -8. The time now is 08:10 AM.

XtremeSystems